Dell S5000 Series User manual

Dell S5000 Series Servers for SAP HANA
Installation Guide
Regulatory Model: M3S2G8, M3UX16
September 2022
Rev. A01

Copyright
© 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc.
or its subsidiaries. Other trademarks may be trademarks of their respective owners.

WARNING: Please read carefully the safety instructions in the Multilingual Safety Notices Guide before you
perform the procedures described in this document.
Intended audience
This document is intended for use by administrators and operators.
Related documents
For the most recent product information, documentation, firmware updates, software fixes, and service offers, see the Dell
Technologies Support Site.
Preface
Preface 3

Contents i
Table of Contents
Chapter 1. Checking the Delivery Contents 1-1.....................................
1.1. Unpacking the Server 1-1..................................................
1.2. Identifying the Server 1-2.................................................
1.2.1. Identifying the Server Model 1-2..................................
1.2.2. Identifying Server Modules 1-2....................................
1.3. Checking Safety Labels 1-4................................................
1.3.1. Server Module Labels 1-4.........................................
1.3.2. UBox Labels 1-7..................................................
Chapter 2. Installing the Server in the Rack Cabinet 2-1...........................
2.1. Installing a S5408 Server 2-1..............................................
2.2. Installing a S5416 Server 2-8..............................................
2.2.1. Installing the Rails for the S5408 Server Assemblies 2-8...........
2.2.2. Installing the Rails for the Ubox(es) 2-14............................
2.2.3. Installing all the Chassis 2-18......................................
2.2.4. Installing the 8-Module Connecting Box 2-26........................
2.2.5. Installing the UBox Components 2-33...............................
Appendix A. Installing a Lightened Server A-1.......................................
A.1. Removing all the Components from the Compute Box A-1...................
A.2. Installing the Compute Box in the Rack Cabinet A-5.........................
A.3. Installing the Components into the Compute Box A-6.......................
Appendix B. Nuts, screws and washers B-1..........................................

Chapter 1. Checking the Delivery Contents 1-1
Chapter 1. Checking the Delivery Contents
D049 DANGER
D049:
The product must not be used in life support system or other
applications where failure could threaten injury or life, and any such
use voids the limited warranty associated to the product.
Important ATTENTION: Please read carefully the safety instructions
before you perform the procedures described in this
manual.
Multilingual Safety Notices Guide
1.1. Unpacking the Server
Important Before unpacking the server inspect the server packaging
for damage.
W020 WARNING
W020:
The server drawer must not be unpacked before it has reached the
room temperature (24 hours in the computer room).
According to the server configuration, the following items are included:
•Compute Box fully populated
•Empty Ubox(es)
•UBox components
•8-module connecting box
•Rack-mounting kits
•Screws and washers

1-2 Installation Guide
1.2. Identifying the Server
1.2.1. Identifying the Server Model
The server model is provided on the safety label on the side of the server.
Model Name Commercial Name
M3S2G8 S5408 server
M3XU16 UBox
1.2.2. Identifying Server Modules
Server modules are identified by an identification label.
The label gives the MAC address of the BMC embedded management controller.
Rear view
The label is located inside a little drawer.
Primary Label Example

Chapter 1. Checking the Delivery Contents 1-3
Secondary Label Example
Front view
A label is also available at the front, behind the bezel.

1-4 Installation Guide
1.3. Checking Safety Labels
Safety warning labels, including safety notices and graphic symbols, are visible
on the server. Check that the electrical installation in place complies with the
label details.
1.3.1. Server Module Labels
Server Identification Label
The label is located on the side of the server.
Mark Description
ACertification information
BRecycling symbol: it is mandatory to reuse and recycle
electronic and electrical equipment properly
CElectric hazard symbol: Caution! Risk of electric shock
DMultiple power sources symbol: Caution! The system has
more than one power source which must all be disconnected
before servicing to avoid shock hazard
EProtectivE conductor symbol: Caution! The system has a high
protective conductor current. The protective conductor (PE)
should be connected first to main protective earthing
terminal before connecting the line and neutral to avoid
shock hazard, and a PE connection to the main PE terminal is
essential before connecting the mains to avoid electric shock
FAltitude symbol: the system must not be operated at an
altitude higher than 2000 meters
GTropicalization symbol: the system must be operated within
the adequate limits of temperature and humidity