Dell EMC PowerStore User manual

PowerStore Quick Start Guide
Quick Start
Copyright © 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, Dell EMC and other trademarks are
trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.
P/N 300-015-650 Rev 01
Before you begin
□Plan your installation: Read the
PowerStore Planning Guide at
https://dell.com/powerstoredocs.
□
Create a support account at
https://dell.com/support.You
need this account later in the
configuration process to activate
software licenses and configure
Dell EMC SupportAssist.
□
Download the
PowerStore
Discovery Tool for Windows
and/ or Linux
from the Drivers &
Downloads Tab on the
PowerStore Product Support
Page at
https://dell.com/support. This
tool helps you discover your
appliances within your network if
you are remote.
□
Get lift assistance:
Obtain the help of a second
person to install the enclosure
into the rack or use a mechanical
lift.
□Install hardware: if installing
PowerStore with expansion
enclosures, read the Installation and
Service Guide for PowerStore 1000,
1200, 3000, 3200, 5000, 5200,
7000, 9000, and 9200 or the
Installation and Service Guide for
PowerStore 500T
https://dell.com/powerstoredocs .
□Configure network: Depending on
the model of your system, read the
PowerStore Networking Guide for
PowerStore X Models or the
PowerStore Networking Guide for
PowerStore T Models at
https://dell.com/powerstoredocs .
□Record network addresses:
Download the networking guide for
your model from
https://dell.com/powerstoredocs,
and work with your network
administrator to complete the Initial
Configuration Worksheet section.
Note: If your appliance arrived pre-racked, begin installation at Step 5 of this guide.
Installation workflow
Record
Dell Serv ice
Ta g

Dell EMC PowerStore Quick Start Guide Page 2of 8
1. Unpack your system
Verify that you have the following:
Base enclosure:
2U base enclosure (1)
Network cables (4)
Rails (2)
Electrostatic discharge clip (1)
Power cables (6, only 2 required per enclosure)
1
Bezel, with key (1)
1Only 4 included for PowerStore 500T
Decide where to install the base enclosure
- Install your base enclosure in the lowest possible space, leaving 2U of space open at the bottom of your cabinet for
serviceability.
- If installing an expansion enclosure, install the expansion enclosure in the next available 2U space, directly above the base
enclosure or the last expansion enclosure in the system.
- Leave 4U at the top of the rack for network switches.
- It is recommended that you also leave 36 inches of clearance in front of and behind the rack for serviceability.
2. Install the rails into your cabinet
When installing the rails, ensure that the rail pins are lined up correctly:
•For the front end of the rail, the bottom pin of the rail goes through the middle hole of the lower U, and the top pin goes through
the top hole of the upper U.
•For the rear end of the rail, the bottom pin of the rail goes through the bottom hole of the lower U, and the top pin goes through
the top hole of the upper U.
1. Position the rail so the label FRONT is located at the front of the rack and facing towards the inside of the rack, while
orienting the rear of the rail to align level with the holes on the rear of the rack.
2. From the rear of the rack, pull the rail straight back until the latch is locked.
3. To install the front-end piece of the rail, press the blue latch release button until the latch rotates open.
Note: The pins on the back of the rails are in different locations than the front of the rails.
4. Pull the rail forward until the pins slide into the holes on the front of the rack, then release the latch to secure the rail in
place.
5. Repeat for the other rail.
Note: Racks are shown with square holes. The installation instructions are the same for racks with round holes. For
racks with threaded holes, remove the guide pin on the rails before installation.

Dell EMC PowerStore Quick Start Guide Page 3of 8
3. Install the base enclosure onto the rails
The base enclosure is heavy and should be installed into or removed from a rack by two people. To avoid personal injury
and/or damage to the equipment, do not attempt to lift and install the base enclosure into a rack without a mechanical
lift and/or help from another person.
1. From the front of the rack, slide the base enclosure onto the rails.
Ensure that the base enclosure is flush with the front of the rack, fully seated in the cabinet, and does not easily slide out.
2. (Optional) If securing the system for shipment in the cabinet or for other unstable environments:
Locate the captive screw under each latch and tighten to the front of the cabinet using a #1 Phillips screwdriver.

Dell EMC PowerStore Quick Start Guide Page 4of 8
4. Record the Dell Service Tag
Locate and record the number from the black Dell Service Tag on the front of the base enclosure.
5. Install optional expansion enclosures
If you are not installing an expansion enclosure, continue to step 7.
If installing an expansion enclosure, determine which type of expansion enclosure you are installing:
25 Drive 2.5 Inch SAS (ESS25) Expansion Enclosure
For each additional expansion enclosure, repeat steps 2 and 3 to install the rails and expansion enclosure onto the rails.
24 Drive 2.5 Inch NVMe (ENS24) Expansion Enclosure
See the Installation and Service Guide for PowerStore 500T or the Installation and Service Guide for PowerStore 1000, 1200,
3000, 3200,5000, 5200, 7000, 9000, and 9200 at https://dell.com/powerstoredocs to install the expansion enclosure into the
cabinet.
6. Connect the expansion enclosure to the base enclosure
See the Label Sheets included with the expansion enclosure for cabling details.
7. Connect the base enclosure to your switches
1. Identify which type of PowerStore model you are deploying: either a PowerStore T model appliance or a PowerStore X
model appliance
2. Choose the cabling instructions for the PowerStore model you are deploying:
Dell Service Tag

Dell EMC PowerStore Quick Start Guide Page 5of 8
Option A
If you are using the PowerStore T Model appliance:
Cable the management interface on both nodes to a management switch or network.
Note: You will require two additional network cables to complete this step.
Note: For more detailed instructions on recommended networking configurations, including how to
configure PowerStore T with top-of-rack switches, see the PowerStore Networking Guide for
PowerStore T Models at https://dell.com/powerstoredocs. Check with your network administrator to
determine which ports on your switches to use.
Option B
If you are using the PowerStore X Model appliance:
Using the supplied cables:
Connect the network cables on node A:
a. Port 0 of the embedded module connects to switch 1.
b. Port 1 of the embedded module connects to switch 2.
Connect the network cables on node B:
a. Port 0 of the embedded module connects to switch 2.
b. Port 1 of the embedded module connects to switch 1.
Note: These instructions show a minimum cabling configuration. For more detailed instructions on
recommended networking configurations, see the PowerStore Networking Guide for PowerStore X Models
at https://dell.com/powerstoredocs. Check with your network administrator to determine which ports on
your switches to use.

Dell EMC PowerStore Quick Start Guide Page 6of 8
8. Power up
a. Expansion enclosure
If installing PowerStore with an expansion enclosure, the order in which you power up the enclosures may differ. See
Installation and Service Guide for PowerStore 500T or the Installation and Service Guide for PowerStore 1000, 1200,
3000, 3200,5000, 5200, 7000, 9000, and 9200 at https://dell.com/powerstoredocs for power up details.
b. Base enclosure
Plug each power cable into the base enclosure power supply unit and close the retention bail over the base of the
power cable. Connect the other end of each power cable to PDU A and PDU B. After you connect the power cables,
the base enclosure automatically starts up.
9. Attach the bezel
1. Align the bezel with the expansion enclosure.
2. Gently push the bezel into place on the cabinet until it latches.
3. Lock the bezel with the provided key.
a. Base enclosure
b. Expansion enclosure
If installing PowerStore with an expansion enclosure, see the Installation and Service Guide for PowerStore 500T or
the Installation and Service Guide for PowerStore 1000, 1200, 3000, 3200,5000, 5200, 7000, 9000, and 9200 at
https://dell.com/powerstoredocs for instructions.
2
1

Dell EMC PowerStore Quick Start Guide Page 7of 8
10. Discover your system
Next, discover your newly installed base enclosure, and then create a cluster.
Note: The procedure in this section only applies if you are physically present within the datacenter. If you do not have access
to the base enclosure, download and run the PowerStore Discovery Utility on a remote system or virtual machine to discover
your system. Refer to the networking guide for your model for more information on setting up your workstation and using the
PowerStore Discovery Utility.
Before you begin:
•(Optional) Download and run the PowerStore Network Validation Tool (NVT) to validate that your networks are
correctly configured. The NVT can be downloaded from Dell EMC Central Solutions at
https://central.dell.com/central/home.
•Ensure that your workstation’s network adapter is configured as follows:
oConnected directly to the PowerStore service port on Node B
oConfigured with a static IP address on the service LAN network (128.221.1.0/24) with no gateway address
defined (128.221.1.249; 255.255.255.0; no gateway)
oAble to ping the IP address of Node B’s service LAN port (128.221.1.251)
1. Connect your workstation or laptop to the service port on Node B of the base enclosure.
B
A
2. In a web browser, go to https://128.221.1.251.
Log on to PowerStore Manager and begin the initial configuration process using the following default credentials:
Username: admin
Default password: Password123#
Note: You must change this default password during initial configuration.
You can disconnect the workstation or laptop from the service port after the initial configuration process is complete.
What’s next?
Use the information from the Initial Configuration Worksheet in the networking guide to configure your cluster for use.

Dell EMC PowerStore Quick Start Guide Page 8of 8
Other languages
You can access localized versions of this and other documents at https://dell.com/support.
您可以在 https://dell.com/support 上访问本文及其他文档的本地化版本。
Локализованные версии этого идругих документов можно найти на веб-сайте https://dell.com/support.
Você pode acessar versões localizadas deste e de outros documentos em https://dell.com/support.
본문서 및기타 문서의 한국어 버전은 https://dell.com/support 에서 이용할 수있습니다.
このドキュメントおよびその他のドキュメントの日本語版は、https://dell.com/support からご覧いただけます。
Des versions traduites du présent document et d’autres documents sont disponibles sur le site Web https://dell.com/support.
Puede obtener acceso a versiones traducidas de este y otros documentos en https://dell.com/support.
Lokalisierte Versionen dieses Dokuments und anderer Dokumente finden Sie unter https://dell.com/support.
Scan the following QR code for troubleshooting, How-To information and setup videos.