Dell PowerVault MD3000i Parts list manual

WARNING: A WARNING indicates a potential for property damage, personal injury,
or death.
Replacing a RAID Controller Module
in a Single-Controller MD3000i
This document describes how to replace a failed RAID controller module in a
single-controller MD3000i. After replacing the RAID controller, you will also
need to update its controller and NVSRAM firmware. These steps are described
in "Updating RAID Controller and NVSRAM Firmware on the Replacement
RAID Controller Module" later in this document.
Replacing the RAID Controller Module
WARNING: Always wear a wrist grounding strap when handling equipment with
static-sensitive components. See your
Product Information Guide for safety
information.
Removing the RAID Controller Module
1 Power down the MD3000i enclosure.
2 Disconnect all cables from the failed RAID controller module.
3 Push up on the release tab on the left side of the module (see Figure 1).
4 At the same time, pull out on the release lever. When the lever is pulled out,
the controller module partially ejects from the enclosure.
5 Remove the module from the enclosure and place it on a flat, secure surface.
CAUTION: To avoid damage to the sensitive EMI (ElectroMagnetic Interference)
contacts on the bottom of the controller module, do not stack or place the module on a
hard surface.

Figure 1. Removing and Installing a RAID Controller Module
Installing a Replacement RAID Controller Module
1 Carefully insert the replacement RAID controller module into the empty
module slot.
2 Push the module into the back of the slot until it is firmly seated in the
backplane connector (see Figure 1).
3 Push the release lever in (towards the enclosure) until the module is retracted
into the slot and is secure.
Proceed to the next section to update the RAID controller and NVSRAM
firmware on the new controller.
1 release tab 2 release lever
2
1

Updating RAID Controller and NVSRAM Firmware
on the Replacement RAID Controller Module
The following procedure is required only if a single controller storage array enters
lockdown mode after replacement of a failed controller.
To update the RAID controller module and NVSRAM firmware, the following
items will be required:
• Server, workstation, or laptop computer with access to the management port
of the RAID controller module
• Single Controller Replacement Utility
Using the Single Controller Replacement Utility
NOTE: The Single Controller Replacement Utility will not update any RAID controller
that is not in lockdown mode. If your RAID controller is not in lockdown mode, use the
update procedure described in the DellTM PowerVaultTM MD3000i User’s Guide.
NOTE: In order to update the firmware, the RAID enclosure must contain at least two
disk drives.
The Single Controller Replacement Utility should be run after replacing a failed
controller in a single-controller system. The utility ensures that the firmware
version in the replacement controller is in sync with the firmware expected by the
virtual disks. After running the utility, the storage array should return to the
configuration it was in prior to the controller failure.
The utility can be run from any computer with access to the management port of
the storage array by following these steps:
1
Extract all files and folders from the utility .zip file to a temporary location.
2 Navigate to the location of the extracted files.
If you are using a Windows system, run the
simplex.bat file.
If you are using a Linux system, execute the
simplex.sh file.
A GUI-based wizard will guide you through the remaining steps necessary to
update the controller.
3 When the wizard completes, click Finish .
The update process is complete.

____________________
Information in this document is subject to change without notice.
© 2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and PowerVault are trademarks of Dell Inc. Other
trademarks and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. Microsoft and Windows are either trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries. Dell Inc. disclaims any proprietary
interest in trademarks and trade names other than its own.
December 2008