Delta Children 7530 User manual

MAY 6, 2014, 24364, R1
Style #:
Lot:
Date:
___________
___________
___________
©2014 DELTA ENTERPRISE CORP.
B
Changing Table
Conforms to
ASTM F2388
Safety Standards
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
REV
THIS PRODUCT IS NOT INTENDED FOR
INSTITUTIONAL OR COMMERCIAL USE.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
When contacting Delta Consumer Care please reference the above information. Before contacting Delta
Consumer Care please ensure that the information above matches the information found on the label on
the Top Shelf, please reference the information found on the product when contacting Delta Consumer
Care.
To register your product for important safety alerts and updates to your product please visit
www.DeltaChildren.com and click on Product Registration.

2
WARNING
FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or
broken. Contact Delta Children’s Products with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by Delta Children’s Products.
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. Left Side x 1
3
G. Top Shelf x 1
H. Bottom Shelf x 2
J. Changer Pad x 1
B. Right Side x 1
C. Back Top Rail x 1
D. Front Top Rail x 1
E. Shelf Rail x 3
F. Front Bottom Rail x 1
K. Restraint Harness x 1
Part # 24354 Part # 24355
Part # 24356
Part # 24357
Part # 24358
Part # 24359
Part # 24360
Part # 24361
Part # 21282
Part # 21748

PARTS:
4
M4 Allen Wrench Supplied
L. M6 x 55 mm Bolt x 12
P. Nut x 2
N. Nylon Washer x 4
M. M6 x 25 mm Bolt x 2
Pliers or Adjustable
Wrench Required
for Assembly
(not supplied)
No drills necessary.
Do not use power
screwdriver.
HARDWARE KIT IS PART #24363-986 FOR COLOR 100 OR #24363-988 FOR
COLOR 205, 207, 604 AND 607 OR #24363-989 FOR COLOR 001.
SEE FRONT COVER.
Part # 5468
Part # 5462
Part # 4065
Part # 5525
Part # 1177
R. M6x17mm Barrel Nut x 12
5479
Flat Head Screwdriver
(not supplied)

5
Attach (1) Back Top Rail (Part C), (1) Front Top Rail (Part D), (3) Shelf Rails (Part E) and (1) Front
Bottom Rail (Part F) to the Left Side (Part A) with (6) M6x55mm Bolts (Part L) and (6) M6x17mm Barrel
Nuts (Part R) using the M4 Allen Wrench as shown. Use the Flat Head Screwdriver to hold the Barrel
Nut in the proper alignment. BE SURE THE GROOVES FACE TO THE INSIDE.
M4 Allen Wrench
Supplied
A. Left Side x 1
Step 1
Section 1: Changing Table Assembly
Parts and tools required to complete step.
A
D
F
E
C
L. M6 x 55 mm Bolt x 6
C. Back Top Rail x 1
D. Front Top Rail x 1
E. Shelf Rail x 3
F. Front Bottom Rail x 1
E
L
L
L
L
L
L
R
R
R
R
R. M6x17mm Barrel Nut x 6
R
R

6
Lay the Left Side on the floor, rails up. Slide the Top Shelf (Part G) in the grooves on the Front Top
Rail and Back Top Rail, into the groove on the Left Side, Slide (2) Bottom Shelves (Part H) in the
grooves on the Shelf Rails and Front Bottom Rail, into the grooves on the Left Side as shown.
From Step 1
H
H
G
G. Top Shelf x 1 H. Bottom Shelf x 2
Step 2
Section 1: Changing Table Assembly
Parts and tools required to complete step.

7
From Step 2
Attach (1) Right Side (Part B) to the assembly from step 2 with (6) M6x55 mm Bolts (Part L) and (6)
M6x17mm Barrel Nuts (Part R) using the M4 Allen Wrench as shown. Use the Flat Head Screwdriver
to hold the Barrel Nut in the proper alignment.
Step 3
Section 1: Changing Table Assembly
Parts and tools required to complete step.
B. Right Side x 1
M4 Allen Wrench
Supplied
L. M6 x 55 mm Bolt x 6
R. M6x17mm Barrel Nut x 6
L
L
L
L
L
LB
R
R
R
R
R
R

8
From Step 3
M4 Allen Wrench Supplied
Align the hole in the end of the strap of the Restraint Harness (Part K) with the hole in the Top Shelf.
Insert (1) M6x25 mm Bolts (Part M) through a Nylon Washer (Part N), the Restraint Strap and the hole
in the Shelf. Add (1) Nylon Washer (Part N) with a Nut (Part P). Hold the Nut with a Pliers or Adjustable
Wrench. Repeat with the other side of the strap as shown.
P. Nut x 2
N. Nylon Washer x 4
K. Restraint Harness x 1
M. M6 x 25 mm Bolt x 2
Pliers or Adjustable
Wrench (Not Supplied)
Step 4
Section 1: Changing Table Assembly
Parts and tools required to complete step.
M
K
N
P
N

9
From Step 4
Place the Changer Pad (Part J) onto the Top Shelf (Part G) on top of the attached Strap from step 4,
Be sure the buckle on the strap is over the Pad as shown.
J. Changer Pad x 1
Step 5
Section 1: Changing Table Assembly
Parts and tools required to complete step.
K

Final
TO FASTEN STRAP - PUSH BUCKLE SIDE TOGETHER
BE SURE BUCKLE IS FULLY FASTENED TO
SECURE CHILD SAFELY
TO RELEASE PRESS BOTH TABS AND PULL APART
10
RESTRAINT HARNESS SYSTEM USE:
. PLACE THE INFANT ON THE CHANGING TABLE FOAM PAD.
. POSITION THE RESTRAINT HARNESS OVER THE MIDDLE OF THE INFANT’S
TORSO AND INSERT THE BUCKLED ENDS INTO EACH OTHER UNTIL THE LOCK
SHUT WITH A CLICK.
. GENTLY PULL THE LOOSE END OF THE STRAP TO LIGHTLY SNUG THE
RESTRAINT HARNESS AROUND THE INFANT.
MAINTENANCE
. CHECK FASTENERS PERIODICALLY FOR TIGHTNESS. DO NOT OVER TIGHTEN.
THIS MAY CAUSE DISTORTION OR BREAKAGE.
WARNING : FALL HAZARD
ALWAY KEEP CHILD WITHIN ARMS REACH.
Section 1: Changing Table Assembly