Delta Childrens Products 7950 User manual

Style #:
Lot:
Date:
___________
___________
___________
©2011 DELTA ENTERPRISE CORP.
A
4 in 1 Crib
Conforms to
ASTM F1169-10a Full
Size Crib & F1821
Safety Standards
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
NOVEMBER 11, 2011, 22504, R0

WARNING:
*Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
*Failure to follow these warnings and the assembly instructions could result in serious injury or death.
DO NOT use this crib if you cannot exactly follow the accompanying instructions.
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string
around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or
attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of
the body or clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or
drapes may strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib
has an adjustable mattress support. For the convenience of the parent when the baby is very small, the
mattress support may be used in the highest position. Important: with the mattress support and
mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches
higher then the top surface of the mattress. If it is not, lower the mattress support and the mattress to
the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm),
whichever occurs first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts,
or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and
other fasteners. Do not use crib if any parts are missing, damaged or broken. Contact Delta
Children's Products for replacement parts and instructional literature if needed. Do not substitute parts.
*Follow warnings on all products in a crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that
every component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
*In Canada Only - Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it
is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the
mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or
who is taller than 90 cm.
CAUTION:
ANY MATTRESS USED IN THIS CRIB SHALL
BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A
THICKNESS NOT EXCEEDING 6 IN.

3
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
TODDLER BED
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in
thickness. The mattress thickness must not exceed 6 in (150mm).

A. Back Top Rail x 1
F. Right Crib End x 1
L. Stabilizer Bar x 1
4
PRODUCT LABEL
B. Back Rail x 1
E. Left Crib End x 1
Part # 22488
Part # 22489
Part # 22494 Part # 22495
Part # 22492
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
G. Mattress Support x 1
Part # 16945
POUCH ATTACHED TO MATTRESS SUPPORT
- KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED OT THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
LEFT INSIDE BOTTOM LABEL
RIGHT INSIDE BOTTOM LABEL
BACK INSIDE BOTTOM LABEL
K. Front Rail x 1
Part # 22491
C. Left Rear Leg x 1
Part # 22496
D. Right Rear Leg x 1
Part # 22497
H. Left Front Leg x 1
Part # 22498
J. Right Front Leg x 1
Part # 22499
N. Day Bed Rail x 1
Part # 22502
M. Stabilizer Bar Molding x 1
Part # 22493
P. Left Front Foot x 1
Part # 22500
Q. Right Front Foot x 1
Part # 22501

5
Z. Φ4x30 mm Metal Pin x 12
HARDWARE KIT PART # 22503 FOR COLOR 100 OR # 22505 FOR COLOR 260,604
AND 607. SEE WARRANTY PAGE.
No drills necessary. Do not
use power screwdriver.
PARTS:
V. M6 x 40 mm Bolt x 6
W. M6 x 30 mm Bolt x 5
Y. M6 x 15 mm Bolt x 12
M4 Allen Wrench Supplied
Part # 5460
Part # 5463
Part # 5465
Part # 5493
Part # 1177
U. M6 x 50 mm Bolt x 16
Part # 5467
S. M6 x 60 mm Bolt x 4
Part # 5469
R. M6 x 110 mm Bolt x 2
Part # 5580
AA. M6 x 16 mm Cap Nut x 2
Part # 5482
Phillips Screwdriver
(not supplied)

6
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
B
D
SECTION 1: CRIB ASSEMBLY
U
C
U
M4 Allen Wrench Supplied
Attach (1) Left Rear Leg (Part C) and (1) Right Rear Leg (Part D) to (1) Back Rail (Part B) using
(2) M6x50mm Bolts (Part U). Tighten with the M4 Allen Wrench.
B. Back Rail x 1
BACK INSIDE BOTTOM LABEL
C. Left Rear Leg x 1
D. Right Rear Leg x 1
BACK INSIDE BOTTOM LABEL
U. M6 x 50 mm Bolt x 2

7
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Insert the slot of the Back Top Rail (Part A) into the tenon on top of the Back Rail (Part B), then insert the (4) M6x50mm
Bolts (Part U), through the legs into the Metal Inserts on the Back Top Rail (Part A) as shown.
From Step 1
U
A
B
U
A. Back Top Rail x 1
BACK INSIDE BOTTOM LABEL
U. M6 x 50 mm Bolt x 4

8
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Attach (1) Left Crib End (Part E) and (1) Right Crib End (Part F) to the assembly from step 2 using (6)
M6x50mm Bolts (Part U). Tighten with the M4 Allen Wrench.
From Step 2
E
F
F. Right Crib End x 1
PRODUCT LABEL
E. Left Crib End x 1
LEFT INSIDE BOTTOM LABEL
RIGHT INSIDE BOTTOM LABEL
U. M6 x 50 mm Bolt x 6
U
U
U
U

9
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
From Step 3
Y. M6 x 15 mm Bolt x 4
G. Mattress Support x 1
WARNING:
!
! WARNINGS ON POUCH MUST FACE UP.
G
!
UP
Attach the Mattress Support (Part G) in all corners using (1) M6 x 15 mm Bolt (Part Y) in each corner.
Tighten with the M4 Allen Wrench.
The Warnings printed on the pouch attached to the
mattress support must face up, the springs must face up.
This crib has (3) adjustment positions, use the highest only
for new borns, move the mattress down as the child grows.
Fall Hazard: When child is able to pull to a standing position,
set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps
for climbing out.
ALL CORNERS
Y

10
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
M
SECTION 1: CRIB ASSEMBLY
W
M4 Allen Wrench Supplied
Attach (1) Stabilizer Bar Molding (Part M) to (1) Stabilizer Bar (Part L) using (2) Φ4x30 mm Metal Pins
(Part Z) and (3) M6x30mm Bolts (Part W). Tighten with the M4 Allen Wrench.
W. M6 x 30 mm Bolt x 3
L. Stabilizer Bar x 1
M. Stabilizer Bar Molding x 1
L
W
W
Z. Φ4x30 mm Metal Pin x 2

11
STEP 6
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
M
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Attach (1) Front Rail (Part K) to the assembly from step 5 using (4) M6x60mm Bolts (Part S).
Tighten with the M4 Allen Wrench.
S. M6 x 60 mm Bolt x 4
From Step 5
K. Front Rail x 1
S
S

12
STEP 7
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
H
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Attach (1) Left Front Foot (Part P) to (1) Left Front Leg (Part H) using (1) Φ4x30 mm Metal Pin (Part Z)
and (1) M6x110mm Bolt (Part R). Tighten with the M4 Allen Wrench.
Attach (1) Right Front Foot (Part Q) to (1) Right Front Leg (Part J) using (1) Φ4x30 mm Metal Pin
(Part Z) and (1) M6x110mm Bolt (Part R). Tighten with the M4 Allen Wrench.
H. Left Front Leg x 1
J. Right Front Leg x 1
R. M6 x 110 mm Bolt x 2
Z. Φ4x30 mm Metal Pin x 2
P. Left Front Foot x 1
Q. Right Front Foot x 1
ZP
Q
Z
J
R
R

13
STEP 8
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
U
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Attach the assembly from step 7 to the assembly from step 6 using (8) Φ4x30 mm Metal Pins (Part Z)
and (4) M6x50mm Bolt (Part U). Tighten with the M4 Allen Wrench.
Z. Φ4x30 mm Metal Pin x 8
From Step 6
From Step 7
U
U
U
Z
Z
Z
Z
Z
Z
U. M6 x 50 mm Bolt x 4

14
STEP 9
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Attach the assembly from step 8 to the assembly from step 4 using (6) M6x40mm Bolts (Part V).
Tighten with the M4 Allen Wrench.
From Step 4 From Step 8
V
V. M6 x 40 mm Bolt x 6
V
V

SECTION 1: CRIB ASSEMBLY
STEP 10
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
15
ASSEMBLY INSTRUCTION
BOOKLET
WARNING: SEE PAGE 2 FOR INFORMATION
Store the assembly instruction booket in the pouch attached to the mattress support. Store all parts
and tools separately, in a safe place.
Style #:
Lot:
Date:
___________
___________
___________
©2011 DELTAENTERPRISE CORP.
A
4 in 1 Crib
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Consumer Care:
www.DeltaChildren.com
Delta Children’sProducts
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
OCTOBER 25, 2011, 22504, R0
AI BAG
Style #:
Lot:
Date:
___________
___________
___________
©2011DELTAENT ERPRISE CORP.
A
4 in 1 Crib
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Consumer Care:
www.DeltaChildren.com
DeltaChildren’s Products
114West 26th Street
NewYork, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
Toregister your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULTASSEMBLY REQUIRED
Dueto the presence of small parts during assembly, keep out of
reachof children until assembly is complete.
OCTOBER25, 2011, 22504, R0

16
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 2: TODDLER BED CONVERSION
M4 Allen Wrench Supplied
Remove the Front Rail Assembly installed in Step 9 of Section 1 crib assembly.
Finished Crib
V
V
V

17
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 2: TODDLER BED CONVERSION
M4 Allen Wrench Supplied
Disassemble the Front Rail Assembly from Step 8 and 6 of Section 1 crib assembly.
From Section 2 Step 1
T
T
T
T

18
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 2: TODDLER BED CONVERSION
M4 Allen Wrench Supplied
From Section 2 Step 2
S
N. Day Bed Rail x 1
S. M6 x 60 mm Bolt x 4
Attach (1) Day Bed Rail (Part N) to the assembly from section 2 step 2 using (4) M6x60mm Bolts
(Part S). Tighten with the M4 Allen Wrench.
S
S
S

19
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 2: TODDLER BED CONVERSION
M4 Allen Wrench Supplied
From Section 2 Step 2
Attach the Left Front Leg and Right Front Leg (from section 2 step 2) to the assembly from section 2
step 3 using (6) Φ4x30 mm Metal Pins (Part Z) and (2) M6x50mm Bolts (Part U). Tighten with the M4
Allen Wrench.
From Section 2 Step 3
Z. Φ4x30 mm Metal Pin x 6
U
U
Z
Z
Z
Z
U. M6 x 50 mm Bolt x 2

20
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 2: TODDLER BED CONVERSION
M4 Allen Wrench Supplied
V. M6 x 40 mm Bolt x 6
From Section 2 Step 1
From Section 2 Step 4
Attach the assembly from section 2 step 4 to the assembly from section 2 step 1 using (6) M6x40mm
Bolts (Part V). Tighten with the M4 Allen Wrench.
V
V
V