Delta Childrens Products 80010 User manual

©2011 DELTA ENTERPRISE CORP.
Customer Service:
Web Site: www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts to the store
from where it was purchased before contacting Delta Children’s Products Customer Service..
Make sure that all preassemble parts are tight. The appearance of your product may be different
from that pictured in this booklet.
To register your product for important safety alerts and updates to your product
please visit www.deltachildrensproducts.com
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
21558, APRIL 15, 2011, R3
FTY
REV
STYLE No: 80010 A
COLOR
Conforms to
ASTM F1169-10a Full
Size Crib, F1821 & F2388
Safety Standards

WARNING: CRIB
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional
padding under an infant.
Failure to follow these warnings and the assembly instructions could result in serious injury or
death.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
ADULT ASSEMBLY REQUIRED DUE TO SMALL PARTS.
*Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a
string around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over
a crib or attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap
parts of the body or clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window where cords from blinds or drapes may
strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position
and remove bumper pads, large toys and other objects that could serve as steps for climbing
out. This crib has an adjustable mattress support. For the convenience of the parent when the
baby is very small, the mattress support may be used in the highest position. Important: with
the mattress support and mattress in the highest position, be absolutely sure that the top of the
front crib side is at least 3 inches higher then the top surface of the mattress. If it is not, lower
the mattress support and the mattress to the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (90cm),
whichever occurs first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, missing parts or sharp edges before
and after assembly and frequently during use. Do not use crib if any parts are missing,
damaged or broken. Contact Delta Children's Products for replacement parts and instructional
literature if needed. Do not substitute parts.
*Follow warnings on all products in a crib.
*Do not use a water mattress with this crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*Ensure a safe environment for the child by checking regularly, before placing the child in the
crib, that every component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping
area.
CAUTION: ANY MATTRESS USED IN THIS
CRIB MUST BE AT LEAST 27 1/4 INCHES BY
51 5/8 INCHES WITH A THICKNESS NOT
EXCEEDING 6 INCHES.
2

TODDLER BED
WARNING ENTRAPMENT/STRANGULATION HAZARD
*INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT AND STRANGULATION. Failure to
follow these warnings and the assembly instructions could result in serious injury or death.
*Never use bed with children under 15 months.
*Never place bed near windows where cords from blinds or drapes may strangle a child.
*Do not place items with a string, cord, or ribbon around a child’s neck, such as hood strings or pacifier
cords.
*Do not suspend strings over a toddler bed for any reason.
*The users maximum weight shall not be greater than 50 lb (22.7kg).
*The mattress intended for use on the bed shall be a full-size crib mattress having minimum dimensions
of 51 5/8 in. (1310 mm) in length, 27 1/4 in. (690 mm) in width and 4 in. (100 mm) in thickness.
*Stabilizer bar(s) must be used when converted to a toddler bed.
3
WARNING: CHANGING TABLE
Fall hazard - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or broken.
Contact Delta Children’s Products with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by Delta Children’s Products.
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
-Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
-Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
-Do not allow any child to play on furniture
-Do not allow climbing on any piece of furniture.
-Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
Always secure the pad to the changing surface by inserting the strap through the hole in the middle of
the pad. See Instructions.

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
B. CHANGER
RIGHT END x 1
4
A. CHANGER
LEFT END x 1
L. CHANGER MIDDLE FRONT SHELF x 1
M. CHANGER MIDDLE BACK SHELF x 1
C. CHANGER BACK
TOP RAIL x 1
F. CHANGER BACK
BOTTOM RAIL x 1
G. CHANGER FRONT TOP
SHELF SUPPORT x 1
E. CHANGER MIDDLE
RAIL x 2
K. CHANGER CENTER BOTTOM RAIL x 1
D. CHANGER FRONT TOP RAIL x 1
H. CHANGER FRONT BOTTOM RAIL x 1
PART # 21485 PART # 21487
PART # 21488
PART # 21489
PART # 21490
PART # 21491
PART # 21492
PART # 21493
PART # 21495
J. CHANGER CENTER TOP RAIL x 1
PART # 21494
PART # 21498
PART # 21499

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
T. CRIB BACK RAIL x 1
5
W. CRIB LEFT END x 1
V. STABILIZER BAR x 1
U. CRIB FRONT
RAIL x 1
X. HAMPER FRONT x 1
Z. HAMPER SIDE x 2
Y. HAMPER BOTTOM x 1
AA. HAMPER BACK x 1
N. CHANGER TOP
CENTER PANEL x 1
P. CHANGER BOTTOM
CENTER PANEL x 1
R. CHANGER SURFACE
WITH STRAP x 1 S. CHANGER PAD x 1
PART # 21480
PART # 21482
PART # 21481
PART # 21483
PART # 21496 PART # 21497
PART # 21500
PART # 21501
PART # 21502
PART # 21503
PART # 21504
PART # 21505

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
6
BB. DRAWER FRONT
PANEL x 2
CC. DRAWER LEFT SIDE
PANEL x 2
EE. DRAWER BACK
PANEL x 2
DD. DRAWER RIGHT SIDE
PANEL x 2
FF. DRAWER BOTTOM PANEL x 2
HARDWARE KIT IS PART # 21559 FOR COLOR 607. SEE FRONT COVER.
PARTS:
JJ. M6 x75 mm BOLT x 8
KK. M6 x50 mm BOLT x 14
LL. M6 x35 mm BOLT x 2
MM. M6 x15 mm BOLT x 4
NN. Φ4x30 mm METAL PIN x 7
PP. BARREL NUT x 8
SS. 25 mm SCREW x 8
TT. 35 mm SCREW x 8
UU. PLASTIC BARREL NUT x 8
RR. 16 mm SCREW x 20
PART # 21506
PART # 21507
PART # 21508
PART # 21509
PART # 21510
VV. HANDLE BOLT x 3
GG. HANDLE x 3
PART # 21557

PARTS:
7
M4 ALLEN WRENCH
SUPPLIED
CASTER WRENCH
NOT SUPPLIED
PHILLIPS SCREWDRIVER
NOT SUPPLIED
POUCH ATTACHED TO MATTRESS SUPPORT
- KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED TO THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
HH. MATTRESS SUPPORT x 1
PART # 21149
WW. CASTER x 4
FLAT HEAD SCREWDRIVER
NOT SUPPLIED
No drills necessary. Do not
use power screwdriver.

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
8
ATTACH (1) CHANGER BACK TOP RAIL (PART C), (1) CHANGER FRONT TOP RAIL (PART D), (2)
CHANGER MIDDLE RAILS (PART E), (1) CHANGER BACK BOTTOM RAIL (PART F), (1) CHANGER
FRONT BOTTOM RAIL (PART H) AND (1) CHANGER CENTER BOTTOM RAIL (PART K) TO THE
CHANGER LEFT END (PART A) USING (1) M6 x35 mm BOLT (PART LL) AND (6) M6 x50 mm BOLT
(PART KK). TIGHTEN WITH M4 ALLEN WRENCH.
A
F
C
A. CHANGER
LEFT END x 1
C. CHANGER BACK
TOP RAIL x 1
F. CHANGER BACK
BOTTOM RAIL x 1
E. CHANGER MIDDLE
RAIL x 2
K. CHANGER CENTER
BOTTOM RAIL x 1
D. CHANGER FRONT
TOP RAIL x 1
H. CHANGER FRONT
BOTTOM RAIL x 1
E
H
D
K
E
M4 ALLEN WRENCH
SUPPLIED
KK. M6 x50 mm BOLT x 6 LL. M6 x35 mm BOLT x 1
KK
KK
KK
KK
KK
KK
LL

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
9
FROM STEP 1
G
J
LAY CHANGER LEFT END (PART A) ON IT’S SIDE AND LOOSELY INSERT (1) CHANGER FRONT TOP
SHELF SUPPORT (PART G) AND (1) CHANGER CENTER TOP RAIL (PART J) AS SHOWN.
G. CHANGER FRONT TOP
SHELF SUPPORT x 1
J. CHANGER CENTER TOP
RAIL x 1

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
10
SLIDE CHANGER SURFACE WITH STRAP (PART R) IN BETWEEN CHANGER BACK TOP RAIL (PART C) AND
CHANGER FRONT TOP SHELF SUPPORT (PART G) GROOVES AS SHOWN.
SLIDE CHANGER TOP CENTER PANEL (PART N) INTO CHANGER SURFACE WITH STRAP (PART R)
AND CHANGER CENTER TOP RAIL (PART J) GROOVES AS SHOWN.
SLIDE CHANGER BOTTOM CENTER PANEL (PART P) INTO CHANGER CENTER TOP RAIL (PART J)
AND CHANGER CENTER BOTTOM RAIL (PART K) GROOVES AS SHOWN.
SLIDE CHANGER MIDDLE FRONT SHELF (PART L) INTO CHANGER MIDDLE RAIL (PART E) AND
CHANGER CENTER TOP RAIL (PART J) GROOVES AS SHOWN.
SLIDE CHANGER MIDDLE BACK SHELF (PART M) INTO CHANGER MIDDLE RAIL (PART E) AND
CHANGER CENTER TOP RAIL (PART J) GROOVES AS SHOWN. ENSURE THAT ALL PANELS
ARE FULLY IN THE GROOVES.
FROM STEP 2
M
P
R. CHANGER SURFACE
WITH STRAP x 1
N
L. CHANGER MIDDLE
FRONT SHELF x 1
M. CHANGER MIDDLE
BACK SHELF x 1
N. CHANGER TOP
CENTER PANEL x 1
P. CHANGER BOTTOM
CENTER PANEL x 1
R
L

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
11
CAREFULLY ALIGN ALL PANELS, TABS AND PINS WITH THE HOLES AND SLOTS IN THE CHANGER
RIGHT END (PART B). INSERT (6) M6x50mm BOLTS (PART KK) AND (1) M6x35mm BOLTS
(PART LL) AS SHOWN. TIGHTEN ALL BOLTS WITH THE M4 ALLEN WRENCH.
FROM STEP 3
B. CHANGER
RIGHT END x 1
M4 ALLEN WRENCH
SUPPLIED
KK
B
KK. M6 x50 mm BOLT x 6
LL. M6 x35 mm BOLT x 1
KK
KK
KK
KK
KK
LL

SECTION 2: CRIB ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
12
FROM SECTION 1
STEP 4
JJ
T. CRIB BACK RAIL x 1
W. CRIB LEFT END x 1 JJ. M6 x75 mm BOLT x 4
PP. BARREL NUT x 4
M4 ALLEN WRENCH
SUPPLIED
JJ
PP
PP
T
W
PP
PP
JJ
JJ
ATTACH (1) CRIB BACK RAIL (PART T) AND (1) CRIB LEFT END (PART W) TO THE ASSEMBLIY
FROM SECTION 1 STEP 4 USING (4) M6x75 mm BOLTS (PART JJ) AND (4) BARREL NUTS
(PART PP). TIGHTEN WITH THE M4 ALLEN WRENCH.USE THE FLAT HEAD SCREWDRIVER TO
HOLD THE BARREL NUT IN THE PROPER ALIGNMENT. DO NOT FULLY TIGHTEN BOLTS AT
THIS TIME, LEAVE SLIGHTLY LOOSE. THEY WILL BE TIGHTENED IN SECTION 2, STEP 4.

SECTION 2: CRIB ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
13
FROM STEP 1
1. INSERT (4) M4x30mm METAL PINS (PART NN) INTO THE HOLE IN EACH OF THE STABILIZER
BAR (PART V).
2. INSERT THE METAL PIN INTO THE HOLES IN THE FRONT POST OF THE FINISHED CHANGING
TABLE. ATTACH WITH (1) M6x75mm BOLT (PART JJ) AND (1) BARREL NUT (PART PP). TIGHTEN
WITH THE M4 ALLEN WRENCH.USE THE FLAT HEAD SCREWDRIVER TO HOLD THE BARREL
NUT IN THE PROPER ALIGNMENT.REPEAT ABOVE WITH THE CRIB END (PART S). DO NOT
TIGHTEN BOLTS COMPLETELY. THEY WILL BE TIGHTENED IN SECTION 2 STEP 4.
V. STABILIZER BAR x 1
JJ. M6 x75 mm BOLT x 2
PP. BARREL NUT x 2
M4 ALLEN WRENCH
SUPPLIED
NN. Φ4x30 mm METAL PIN x 4
JJ
JJ
V
V
NN
NN
PP
PP
PP
V
JJ
PULL GENTLY

SECTION 2: CRIB ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
14
FROM STEP 2
ATTACH THE MATTRESS SUPPORT (PART HH) IN ALL CORNERS USING (1) M6x15 mm BOLT
(PART MM) IN EACH CORNER. TIGHTEN WITH THE M4 ALLEN WRENCH.
THE WARNINGS PRINTED ON THE POUCH ATTACHED
TO THE MATTRESS SUPPORT MUST FACE UP, THE
SPRINGS MUST FACE UP.
THIS CRIB HAS (3) ADJUSTMENT POSITIONS, USE THE
HIGHEST ONLY FOR NEW BORNS, MOVE THE
MATTRESS DOWN AS THE CHILD GROWS.
WARNING:
FALL HAZARD: WHEN CHILD IS ABLE TO PULL TO A
STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS
AND OTHER OBJECTS THAT COULD SERVE AS STEPS
FOR CLIMBING OUT.
!
! WARNINGS ON POUCH MUST FACE UP.
ALL CORNERS
!
UP
MM
HH
M4 ALLEN WRENCH
SUPPLIED
HH. MATTRESS SUPPORT x 1
MM. M6 x15 mm BOLT x 4

SECTION 2: CRIB ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
15
ATTACH THE CRIB FRONT SIDE (PART U) TO THE ASSEMBLY FROM STEP 3 USING (3) M4x30mm METAL
PINS (PART NN) , (2) M6x50mm BOLTS (PART KK), (2) M6x75mm BOLTS (PART JJ) AND (2) BARREL NUTS
(PART PP).TIGHTEN ALL BOLTS, INCLUDING THE BOLT INSTALLED LOOSELY IN SECTION2 STEP
1 AND 2, WITH THE M4 ALLEN WRENCH. USE THE FLAT HEAD SCREWDRIVER TO HOLD THE
BARREL NUT IN THE PROPER
ALIGNMENT.
FROM STEP 3
U
NN
KK
PULL GENTLY
JJ. M6 x75 mm BOLT x 2
PP. BARREL NUT x 2
M4 ALLEN WRENCH
SUPPLIED
U. CRIB FRONT
SIDE x 1
NN. Φ4x30 mm METAL PIN x 3
KK. M6 x50 mm BOLT x 2
JJ
NN
KK
JJ
PP
PP
U
JJ
PP
NN
KK

SECTION 3: HAMPER ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
16
SLIDE HAMPER BOTTOM (PART Y) AGAINST THE HAMPER FRONT, SO THAT IT FITS SNUG UNDER AND
OVER THE BARS AS SHOWN. THEN ATTACH THE HAMPER BOTTOM (PART Y) TO THE HAMPER FRONT
(PART X) WITH (1) 16mm SCREW (PART RR) . TIGHTEN WITH THE PHILLIPS SCREWDRIVER.
PHILLIPS SCREWDRIVER
NOT SUPPLIED
X
TOP
X. HAMPER FRONT x 1 Y. HAMPER BOTTOM x 1
X
YY
RR
TOP
RR. 16 mm SCREW x 1

SECTION 3: HAMPER ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
17
ATTACH (2) HAMPER SIDES (PART Z) TO THE ASSEMBLY FROM STEP 1 WITH (5) 16mm SCREWS (PART RR)
FOR EACH. TIGHTEN WITH THE PHILLIPS SCREWDRIVER.
PHILLIPS SCREWDRIVER
NOT SUPPLIED
FROM STEP 1
Y
RR
Z. HAMPER SIDE x 2
TOP
RR
RR
RR
RR
Y
RR
RR
RR
RR. 16 mm SCREW x 10

SECTION 3: HAMPER ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
18
ATTACH THE HAMPER BACK (PART AA) TO THE ASSEMBLY FROM STEP 2 WITH (9) 16mm SCREWS
(PART RR). TIGHTEN WITH THE PHILLIPS SCREWDRIVER.
ENSURE THAT THE EDGES OF THE BACK LINE UP WITH THE EDGES OF THE SIDES.
PHILLIPS SCREWDRIVER
NOT SUPPLIED
FROM STEP 2 AA. HAMPER BACK x 1
TOP
RR
RR
RR
RR
RR
RR
RR
RR
AA
RR
FRONT
BOTTOM
RR. 16 mm SCREW x 9

SECTION 3: HAMPER ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
19
ATTACH (4) CASTERS (PART WW) TO THE HAMPER BOTTOM IN THE THREADED HOLES. TIGHTEN WITH THE
CASTER WRENCH.
FROM STEP 3
WW. CASTER x 4
CASTER WRENCH
NOT SUPPLIED
WW
! ENSURE 4 PER-DRILLED HOLES
FOR THE CASTERS OUTWARDS.
WW
BOTTOM

SECTION 3: HAMPER ASSEMBLY
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
20
ATTACH THE HANDLE (PART GG) TO THE ASSEMBLY FROM STEP 4 USING (1) HANDLE BOLT (PART VV).
TIGHTEN WITH THE PHILLIPS SCREWDRIVER.
PHILLIPS SCREWDRIVER
NOT SUPPLIED
GG
FROM STEP 4
GG. HANDLE x 1
VV. HANDLE BOLT x 1
VV