Delta Childrens Products 7334-A User manual

4 in 1 Crib
APRIL 12, 2014, 24560, R1
Style #:
Lot:
Date:
___________
___________
___________
©2014 DELTA ENTERPRISE CORP.
A
Conforms to
ASTM F1169 Full
Size Crib & F1821
Safety Standards
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
REV
THIS PRODUCT IS NOT INTENDED FOR
INSTITUTIONAL OR COMMERCIAL USE.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
When contacting Delta Consumer Care please reference the above information. Before contacting Delta
Consumer Care please ensure that the information above matches the information found on the label on
the Crib End bottom rail, please reference the information found on the product when contacting Delta
Consumer Care.
To register your product for important safety alerts and updates to your product please visit
www.DeltaChildren.com and click on Product Registration.

WARNING:
*Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an
infant.
*Failure to follow these warnings and the assembly instructions could result in serious injury or death.
DO NOT use
this crib if you cannot exactly follow the accompanying instructions.
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string around a
child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or drapes may
strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out. This crib has an adjustable mattress
support. For the convenience of the parent when the baby is very small, the mattress support may be used in the
highest position. Important: with the mattress support and mattress in the highest position, be absolutely sure that
the top of the front crib side is at least 3 inches higher than the top surface of the mattress. If it is not, lower the
mattress support and the mattress to the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm), whichever occurs
first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges
before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. Do not use
crib if any parts are missing, damaged or broken. Contact Delta Children's Products for replacement parts and
instructional literature if needed. Do not substitute parts.
*Follow warnings on all products in a crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that every
component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
*In Canada Only - Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it is pushed
firmly against any side of the crib, it does not leave a gap of more than 3 cm between the mattress and any part of
the sides of the crib. Do not use this crib for a child who can climb out of it or who is taller than 90 cm.
CAUTION:
ANY MATTRESS USED IN THIS CRIB SHALL
BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A
THICKNESS NOT EXCEEDING 6 IN.

3
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between toddler bed parts can entrap head and neck of a small child.
NEVER use toddler bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and a max thickness of
6 in (150 mm).
TODDLER BED

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. Back Top Rail x 1
G. Left Back Post x 1 H. Right Back Post x 1
J. Mattress Support x 1
4
E. Left Crib Side x 1 F. Right Crib Side x 1
B. Back Rail x 1
D. Stabilizer Bar x 1
POUCH ATTACHED TO MATTRESS SUPPORT
- KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED TO THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
Part # 24291
Part # 24559
Part # 24295 Part # 24296
Part # 24297 Part # 24298
Part # 24294
Part # 24242
C. Front Rail x 1
Part # 24293
PRODUCT LABEL
LEFT INSIDE BOTTOM LABEL
RIGHT INSIDE BOTTOM LABEL

PARTS: HARDWARE KIT IS PART #24299-988 FOR COLOR 648. SEE FRONT COVER.
5
R. M6x17mm Barrel Nut x 14
M4 Allen Wrench Supplied
L. M6 x 55 mm Bolt x 6
K. M6 x 75 mm Bolt x 10
N. M6 x 18 mm Bolt x 4
P. Φ4x30 mm Metal Pin x 2
Part # 1177
Part # 5472
Part # 5468
Part # 5763
Part # 5493
Part # 5479
No drills necessary.
Do not use power
screwdriver.
Flat Head Screwdriver
(not supplied)

R. M6x17mm Barrel Nut x 4
6
Attach (1) Left Back Post (Part G) to (1) Left Crib Side (Part E) using (2) M6x55 mm Bolts (Part L) and
(2) M6x17 mm Barrel Nuts (Part R). Tighten with the M4 Allen Wrench. Use the Flat Head Screwdriver
to hold the Barrel Nut in the proper alignment. Repeat with the Right Crib Side (Part F) and Right Back
Post (Part H).
M4 Allen Wrench
Supplied
G
Step 1
Section 1: Crib Assembly
Parts and tools required to complete step.
R
L
G. Left Back Post x 1
H. Right Back Post x 1
E. Left Crib Side x 1
Left Crib Side
F. Right Crib Side x 1
L
E
L. M6 x 55 mm Bolt x 4
R
PRODUCT LABEL
LEFT INSIDE BOTTOM LABEL
PRODUCT LABEL
LEFT INSIDE BOTTOM LABEL
INSIDE
RIGHT INSIDE BOTTOM LABEL

R. M6x17mm Barrel Nut x 2
From Step 1
7
Attach (1) Back Rail (Part B) to the assemblies from step 1 using (2) M6x75 mm Bolts (Part K) and
(2) M6 x 17 mm Barrel Nuts (Part R). Tighten with the M4 Allen Wrench. Use the Flat Head Screwdriver
to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench
Supplied
Step 2
Section 1: Crib Assembly
Parts and tools required to complete step.
B. Back Rail x 1
B
R
R
K
K. M6 x 75 mm Bolt x 2
K
BACK!

K. M6 x 75 mm Bolt x 2
Attach (1) Back Top Rail (Part A) to the assembly from step 2 using (2) M6x55 mm Bolts (Part L),
(2) M6x75 mm Bolts (Part K) and (2) M6 x 17 mm Barrel Nuts (Part R). Tighten with the M4 Allen
Wrench. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
8
From Step 2
Step 3
Section 1: Crib Assembly
Parts and tools required to complete step.
A. Back Top Rail x 1
R. M6x17mm Barrel Nut x 2
M4 Allen Wrench
Supplied
L. M6 x 55 mm Bolt x 2
L
AR
K
L
K
R
BACK!

9
From Step 3
Attach the Mattress Support (Part J) in all corners using (1) M6x18 mm Bolt (Part N) in each corner.
Tighten with the M4 Allen Wrench.
! WARNINGS ON POUCH MUST FACE UP.
J
ALL CORNERS
UP
M4 Allen Wrench
Supplied
J. Mattress Support x 1
WARNING:
!
!
The Warnings printed on the pouch attached to the
mattress support must face up, the springs must face up.
This crib has (3) adjustment positions, use the highest only
for new borns, move the mattress down as the child grows.
Fall Hazard: When child is able to pull to a standing position,
set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps
for climbing out.
Step 4
Section 1: Crib Assembly
Parts and tools required to complete step.
N. M6 x 18 mm Bolt x 4
N

K. M6 x 75 mm Bolt x 2
Attach (1) Front Rail (Part C) to the assembly from step 4 using (2) M6x75 mm Bolts (Part K) and (2)
M6 x 17 mm Barrel Nuts (Part R). Tighten with the M4 Allen Wrench. Use the Flat Head Screwdriver to
hold the Barrel Nut in the proper alignment.
10
From Step 4
Step 5
Section 1: Crib Assembly
Parts and tools required to complete step.
R. M6x17mm Barrel Nut x 2
M4 Allen Wrench
Supplied
C. Front Rail x 1
C
K
K
R
R

K. M6 x 75 mm Bolt x 4
Attach (1) Stabilizer Bar (Part D) to the assembly from step 5 using (2) Φ4x30 mm Metal Pins (Part P),
(4) M6x75 mm Bolts (Part K) and (4) M6 x 17 mm Barrel Nuts (Part R). Tighten with the M4 Allen
Wrench. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
11
From Step 5
Step 6
Section 1: Crib Assembly
Parts and tools required to complete step.
R. M6x17mm Barrel Nut x 4
M4 Allen Wrench
Supplied
D. Stabilizer Bar x 1
P. Φ4x30 mm Metal Pin x 2
K
R
K
K
R
D
P

12
Assembly Instruction
Booklet
WARNING: SEE PAGE 2 FOR INFORMATION
AI BAG
Store the assembly instruction booklet in the pouch attached to the mattress support. Store all parts
and tools separately, in a safe place.
Step 7
Section 1: Crib Assembly
Parts and tools required to complete step.
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Style #:
Lot:
Date:
___________
___________
___________
A
4 in 1 Crib
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer Care please reference
the above information. Before contacting Delta Consumer
Care please ensure that the information above matches the
information found on the label on the Crib End bottom rail,
please reference the information found on the product
when contacting Delta Consumer Care.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
AUGUST26, 2013, 24560, R0 ©2013 DELTAENTERPRISE CORP.
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Style #:
Lot:
Date:
___________
___________
___________
A
4 in 1 Crib
Consumer Care:
www.DeltaChildren.com
DeltaChildren ’s Products
114West 2 6th Street
NewYork, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
Toregister your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer Care please reference
the above information. Before contacting Delta Consumer
Care please ensure that the information above matches the
information found on the label on the Crib End bottom rail,
please reference the information found on the product
when contacting Delta Consumer Care.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Dueto the presence of small parts during assembly, keep out of
reachof children until assembly is complete.
AUGUST26, 2013, 24560, R0 ©2013DELTA ENTERPRISE CORP.

Finished Crib
Remove the Front Rail and the Stabilizer Bar installed in Step 5 and 6 of Section 1 crib assembly.
13
M4 Allen Wrench
Supplied
Step 1
Section 2: Toddler Bed Conversion
Parts and tools required to complete step.
D
C
K
R
K
PULL GENTLY
K
K
R
K
K
PULL GENTLY

Attach (1) Stabilizer Bar (Part D) to the assembly from section 2 step 1 using (4) M6x75 mm Bolts
(Part K) and (4) M6x17 mm Barrel Nuts (Part R). Tighten with the M4 Allen Wrench. Use the Flat Head
Screwdriver to hold the Barrel Nut in the proper alignment.
14
From Section 2 Step 1
M4 Allen Wrench Supplied
Step 2
Section 2: Toddler Bed Conversion
Parts and tools required to complete step.
D. Stabilizer Bar x 1
R. M6x17mm Barrel Nut x 4
K. M6 x 75 mm Bolt x 4
K
K
DR
K
R

15
WARNING:
TODDLER BED WARNINGS
SEE PAGE 3 FOR
The mattress support must be in the lowest position.
Store all hardware safely.
Read all warnings on page 3.
As shown, use as a day bed or love seat sofa.
Do Not use without stabilizer bar installed.
Stabilizer bar must be used when converted
to a toddler bed.
A toddler bed guardrail is available for this
crib.
Please see your crib retailer, visit
www.DeltaChildren.com or contact Delta
Consumer Care for more information.
This crib uses Delta Style # 0080 Guardrail.
Step 3
Section 2: Toddler Bed Conversion

16
M4 Allen Wrench
Supplied
Step 1
Section 3: Full Size Bed Conversion
Parts and tools required to complete step.
You have the option to convert the crib to a Full Size Bed. Simply follow the steps in reverse order to
disassemble the crib. Stop after removing the left and right crib sides with the M4 Allen Wrench
as shown.
Store all parts and hardware in a safe place.
E
F

17
From Section 3 Step 1 M4 Allen Wrench
Supplied
Step 2
Section 3: Full Size Bed Conversion
Parts and tools required to complete step.
Attach Bed Frame to the Headboard (From Section 3 Step 1) using (4) M6x18mm Bolts (Part N).
Follow all instructions supplied with the Bed Frame. Note: Bed Frame System is not included, see
you furniture or mattress retailer. Contact Delta Children’s Products for information or with questions.
N. M6 x 18 mm Bolt x 4

Warranty: This Delta Crib is warranted to be free from defects for a period
of 1 year from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
[phone].
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Crib End bottom rail.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)
COLOR FTY
REV
STYLE No: 7334 A
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033