Delta Childrens Products S26932 User manual

Style #:
Lot:
Date:
___________
___________
___________
©2012 DELTA ENTERPRISE CORP.
A
Changer
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Back
Panel.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
JANUARY 18, 2012, 22817, R0
Conforms to
ASTM F2388
Safety Standards

2
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
WARNING
FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or
broken. Contact Delta Children’s Products with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by Delta Children’s Products.
WARNING: Changing Table

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
3
A. Top Panel x 2 B. Shelf Panel x 2
Part # 22642 Part # 22643
C. Bottom Panel x 2
Part # 22644
D. Left Panel x 2
Part # 22645
E. Right Panel x 2
Part # 22646
F. Back Panel x 2
Part # 22647
G. Front Rail x 1
Part # 22648
H. Top Back Rail x 1
Part # 22650
J. Top Front Rail x 1
Part # 22649
K. Top Left Rail x 1
Part # 22651
L. Top Right Rail x 1
Part # 22652
M. Changer Pad x 1
Part # 22740

PARTS:
4
R. Φ8x30 mm Wood Dowel x 32
S. 25mm Pan Head Wood Screw x 4
Phillips Screwdriver
(not supplied)
No drills necessary. Do not
use power screwdriver.
HARDWARE KIT PART #22653 FOR COLOR 607 OR #22656 FOR COLOR 001.
SEE COVER PAGE.
Part # 5486
Part # 5495
N. Cam Lock x 36
Part # 5519
P. Cam Bolt x 36
Part # 5566
T. 15mm Flat Head Wood Screw x 4
Part # 4521
U. 16mm Washer Head Wood Screw x 34
Part # 5585
V. Bracket x 2
Part # 5586
(not supplied)
Flat Head Screwdriver

5

SECTION 1: CHANGER ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
6
D
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Insert the cams.
3. Cam bolts must be screwed down flush.
4. Refer to page 5 for instructions on how to use the cam lock system.
D. Left Panel x 2
N. Cam Lock x 4 P. Cam Bolt x 10
R. Φ8x30 mm Wood Dowel x 4
P
P
P
P
R
R
(2x)
N
N
P

SECTION 1: CHANGER ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
7
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Insert the cams.
3. Refer to page 5 for instructions on how to use the cam lock system.
From Step 1
N. Cam Lock x 8
R. Φ8x30 mm Wood Dowel x 8
B. Shelf Panel x 2
(2x)
B
N
N
N
N
R
R
R
R
B
Please make sure
finished surface is
facing the front.
(2x)
(2x)

SECTION 1: CHANGER ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
8
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Insert the cams.
3. Refer to page 5 for instructions on how to use the cam lock system.
From Step 2
N. Cam Lock x 12
R. Φ8x30 mm Wood Dowel x 8
(2x)
C
N
R
C
(2x)
(2x)
C. Bottom Panel x 2
R
R
R
N
N
N
N
N

SECTION 1: CHANGER ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
9
E
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Insert the cams.
3. Cam bolts must be screwed down flush.
4. Refer to page 5 for instructions on how to use the cam lock system.
N. Cam Lock x 4 P. Cam Bolt x 10
R. Φ8x30 mm Wood Dowel x 4
P
P
P
P
R
R
(2x)
N
N
P
E. Right Panel x 2

SECTION 1: CHANGER ASSEMBLY
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
10
1. Refer to page 5 for instructions on how to use the cam lock system.
2. Assemble the assembly from step 4 to the assembly from step 3 as shown on the attached illustration.
From Step 3
E
(2x)
(2x)
From Step 4
(2x)

SECTION 1: CHANGER ASSEMBLY
STEP 6
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
11
A
1. Cam bolts must be screwed down flush.
2. Refer to page 5 for instructions on how to use the cam lock system.
P. Cam Bolt x 12
(2x)
A. Top Panel x 2
P
P
P
P
P
P

SECTION 1: CHANGER ASSEMBLY
STEP 7
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
12
From Step 5
A
(2x)
(2x)
From Step 6
(2x)
1. Refer to page 5 for instructions on how to use the cam lock system.
2. Assemble the assembly from step 6 to the assembly from step 5 as shown on the attached illustration.

SECTION 1: CHANGER ASSEMBLY
STEP 8
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
13
From Step 7
U
(2x)
(2x)
Attach (1) Back Panel (Part F) to the assembly from step 7 using (17)16mm Washer Head Wood Screws
(Part U). Tighten with the Phillips Screwdriver. Repeat the other Back Panel.
F. Back Panel x 2
U. 16mm Washer Head
Wood Screw x 34
U
U
U
U
U
U
U
F

SECTION 1: CHANGER ASSEMBLY
STEP 9
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
14
From Step 8
G. Front Rail x 1
R. Φ8x30 mm Wood Dowel x 4
N. Cam Lock x 4
2. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
3. Insert the cams.
4. Refer to page 5 for instructions on how to use the cam lock system.
N
N
N
N
G
R
R
R
R
G
V. Bracket x 2
T. 15mm Flat Head
WoodScrewx 4
1. Using (2) Brackets (Part V) and (4)15mm Flat Head Wood Screws (Part V) to connect both assemblies
from step 8. Tighten with the Phillips Screwdriver.
(2x)
T
V
T
T
T
T
T
V

SECTION 1: CHANGER ASSEMBLY
STEP 10
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
15
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Insert the cams.
3. Cam bolts must be screwed down flush.
4. Refer to page 5 for instructions on how to use the cam lock system.
N. Cam Lock x 4
P. Cam Bolt x 4
R. Φ8x30 mm Wood Dowel x 4
P
R
R
N
H. Top Back Rail x 1
J. Top Front Rail x 1 K. Top Left Rail x 1
L. Top Right Rail x 1
P
P
N
R
N
R
N
P
H
L
J
K

SECTION 1: CHANGER ASSEMBLY
STEP 11
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
16
Refer to page 5 for instructions on how to use the cam lock system.
From Step 10
H
L
J
K

SECTION 1: CHANGER ASSEMBLY
STEP 12
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
17
From Step 11
From Step 9
S. 25mm Pan Head WoodScrewx 4
Attach the assembly from step 11 to the assembly from step 9 using (4) 25mm Pan Head Wood Screws
(Part S). Tighten with the Phillips Screwdriver.
S
S
S
S

SECTION 1: CHANGER ASSEMBLY
STEP 13
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
18
From Step 12
Place the Changer Pad (Part M) onto the Top Panels (Part A).
M
M. Changer Pad x 1
A
A
FINAL
Tip-over restraint
Note: Tip-over restraints have been provided. Please install these following the instructions
included in the kit.

SECTION 2: CONVERTING TO NIGHT STANDS
19
S
S
S
S
G
T
TV
T
T
V
1. Remove top installed in step 12.
2. Remove front rail and brackets installed in step 9. Remove exposed Cam Bolts (Part P)
3. (2) Nightstands (as assembled in step 8). Ensure dowels are removed.Disassemble all unused
components and store all parts safely.
T
T
P
FINAL
Note: Tip-over restraints have been
provided. Please install these following
the instructions included in the kit.
Tip-over restraint

Warranty: This Delta product is warranted to be free from defects for a period
of 90 days from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
[phone].
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Back Panel.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)
COLOR FTY
REV
STYLE No: S26932-Changer A