Delta Childrens Products 70816-607 User manual

October 22, 2010 ©2010 DELTA ENTERPRISE CORP.
Customer Service:
Web Site: www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts to the store
from where it was purchased before contacting Delta Children’s Products Customer Service..
Make sure that all preassemble parts are tight. The appearance of your product may be different
from that pictured in this booklet.
To register your product for important safety alerts and updates to your product
please visit http://deltaenterprise.com/register.asp
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
COLOR FTY
REV
STYLE No: ______-
21330 - R4
607 AWJ

2
PARTS:
BOLTS AND SCREWS ARE SHOWN FULL SIZE.
WARNING:
Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:
.Place heaviest items in the lowest drawers.
.Unless specifically designed to accommodate, do not set TV’s or other heavy objects on the top of this product.
.Never allow children to climb or hang on drawers, doors,or shelves.
.Never open more than one drawer at a time.
Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.
.Always monitor your child’s activity when in the nursery.
.Do not allow standing in drawers.
.Do not allow standing on top of this product.
.Accessory Items must be securely fastened to this product according to the instructions provided with those
items.
.To avoid head injury, do not allow children to play underneath open drawers.
.Do not leave drawers open when not in use.
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the
diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape specified in
the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly recommended that
assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp,
cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or felt pad
under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
A. DRAWER FRONT - LEFT DRAWER (x3) B. DRAWER FRONT - RIGHT DRAWER (x3)
C. LEFT DRAWER SIDE (x6) D. RIGHT DRAWER SIDE (x6)
F. DRAWER BOTTOM (x6)
E. DRAWER
BACK (x6)
G. DRAWER SUPPORT (x6) H. KNOB (x6)
J. DRAWER ASSEMBLY SCREW (x54) K. KNOB SCREW (x6)

3
PARTS-CONTINUED:
BOLTS AND SCREWS ARE SHOWN FULL SIZE.
L. LEFT SIDE PANEL (x1) M. CENTER FRAME (x1) N. RIGHT SIDE PANEL (x1)
P. TOP (x1)
R2. BACK BOTTOM SUPPORT
RAIL - UNFINISHED (x1)
S. UPPER SUPPORT RAIL (x4)
T. BACK PANEL (x2)
V. BACK PANEL SCREW (x28)
W. SHORT BOLT(x4)
X. LONG BOLT(x10) M4 ALLEN WRENCH
SUPPLIED
R1. FRONTBOTTOM SUPPORT
RAIL - FINISHED (x1)

4
SECTION 1: DRAWER ASSEMBLY
STEP 1
FIG. 1
J
C
A or B
F
G
D
1. ATTACH THE LEFT DRAWER SIDE (PART C) TO THE DRAWER FRONT (PART A OR B)
USING (2) DRAWER ASSEMBLY SCREWS (PART J), TIGHTEN WITH THE PHILLIPS
SCREWDRIVER. BE SURE THE GROOVE IN THE BOTTOM OF THE PARTS LINE UP. SEE
FIGURE 1. THE METAL DRAWER GUIDE MUST BE TO THE OUTSIDE. REPEAT WITH THE
RIGHT DRAWER SIDE (PART D)
2. SLIDE THE DRAWER BOTTOM (PART F)
INTO THE GROOVES ON THE DRAWER SIDES,
UNTIL IT IS IN THE GROOVE ON THE DRAWER
FRONT. BE SURE THE NOTCHED CORNERS
ARE TOWARDS THE DRAWER FRONT.
3. INSERT THE DRAWER SUPPORT (PART
G) INTO THE CUTOUT IN THE DRAWER
FRONT. BE SURE THE END OF THE
DRAWER SUPPORT WITH THE
PRE-DRILLED HOLE IS TO THE BACK.

5
SECTION 1: DRAWER ASSEMBLY
STEP 2 E
H
K
J
J
J
1. ATTACH THE DRAWER BACK (PART E) TO
THE DRAWER ASSEMBLY USING (5) DRAWER
ASSEMBLY SCREWS (PART J), TIGHTEN WITH
THE PHILLIPS SCREWDRIVER. BE SURE THE
DRAWER BOTTOM IS IN THE GROOVE ON THE
DRAWER BACK BEFORE ATTACHING ANY
SCREWS.
2. ATTACH THE KNOB (PART H) TO THE
DRAWER ASSEMBLY USING (1) KNOB SCREW
(PART K) TIGHTEN WITH THE PHILLIPS
SCREWDRIVER.
3. REPEAT FOR ALL OTHER DRAWER FRONTS (PART A OR B).
ASSEMBLED LEFT DRAWER (x3) ASSEMBLED RIGHT DRAWER (x3)

6
SECTION 2: CASE ASSEMBLY
STEP 1
X
P
L
W
FOR CASE ASSEMBLY PLACE THE TOP (PART P) ON A STABLE,
NON-ABRASIVE SURFACE, SUCH AS A BLANKET ON THE FLOOR.
1. ATTACH THE LEFT SIDE PANEL (PART L) TO THE TOP (PART P) USING
(2) LONG BOLTS (PART X), TIGHTEN WITH THE M4 ALLEN WRENCH.
2. FINISH THE ATTACHMENT OF THE LEFT
SIDE PANEL BY INSTALLING (2) SHORT
BOLTS (PART W) AS SHOWN, TIGHTEN WITH
THE M4 ALLEN WRENCH.

7
SECTION 2: CASE ASSEMBLY
STEP 2
FIG 2
FIG 3
S
R
M
X
X
2a. INSERT THE TABS ON THE END OF THE CENTER FRAME (PART M) INTO THE SLOTS IN
THE RAILS ON THE TOP. BE SURE THE DRAWER GUIDES ARE IN THE SAME DIRECTION AS
THOSE ON THE SIDE PANEL. INSERT THE UPPER SUPPORT RAILS INTO THE SLOTS ON
THE CENTER FRAME. TAKE CARE NOT TO SCRATCH THE FINISH.
2b. INSTALL (2) BOTTOM SUPPORT RAILS (PART R) BY INSERTING THE TABS ON THE
BOTTOM SUPPORT RAILS INTO THE SIDE PANEL AND INSERTING THE TABS ON THE
CENTER FRAME INTO THE BOTTOM SUPPORT RAILS. SEE FIGURE 2. FINISHED SIDE MUST
FACE FRONT.
2c. INSTALL (2) LONG BOLTS (PART X) THROUGH THE SIDE PANEL. TIGHTEN WITH THE M4
ALLEN WRENCH.
2d. INSTALL (2) LONG BOLTS (PART X) THROUGH THE CENTER FRAME, TIGHTEN WITH THE
M4 ALLEN WRENCH. SEE FIGURE 3.
1. INSERT (2) UPPER SUPPORT RAILS
(PART S) INTO THE SLOTS IN THE
FRONT POST OF THE SIDE PANEL.
FINISHED PANEL MUST FACE FRONT.
FINISHED SIDE
MUST FACE
FRONT.

8
SECTION 2: CASE ASSEMBLY
STEP 3
X
X
S
N
W
2a. INSTALL THE RIGHT SIDE PANEL (PART N) BY ALIGNING THE TABS ON
ALL OF THE INSTALLED PIECES WITH THE SLOTS IN THE SIDE PANEL. IT IS
TYPICALLY EASIEST TO START WHERE THE SIDE PANEL MEETS THE TOP
AND WORK TO THE BOTTOM SUPPORT RAILS.
2b. INSTALL (4) LONG BOLTS (PART X) THROUGH THE SIDE PANEL, TIGHTEN
WITH THE M4 ALLEN WRENCH.
3. FINISH THE ATTACHMENT OF THE RIGHT
SIDE PANEL BY INSTALLING (2) SHORT
BOLTS (PART W) AS SHOWN, TIGHTEN WITH
THE M4 ALLEN WRENCH.
1. INSERT (2) UPPER SUPPORT RAILS
(PART S) INTO THE SLOTS IN THE
FRONT POST OF THE CENTER FRAME.
FINISHED SIDE MUST FACE FRONT.
FINISHED SIDE
MUST FACE
FRONT.

9
SECTION 2: CASE ASSEMBLY
STEP 4
T
V
INSTALL THE BACK PANELS (PART T) USING (14)
BACK PANEL SCREWS (PART V) FOR EACH.
TIGHTEN WITH THE PHILLIPS SCREWDRIVER.
ABOVE ONE BACK PANEL IS SHOWN INSTALLED.
THE SMALL NOTCH IN THE BACK PANEL MUST BE
INSTALLED AS SHOWN AS CAN BE SEEN IN FIGURE
3, THE NOTCH LINES UP WITH A NOTCH IN THE RAIL
PRE-ASSEMBLED TO THE TOP. THIS WILL ALLOW
ATTACHMENT OF THE WALL STRAP - SEE KIT FOR
INSTRUCTIONS ON USE.

10
SECTION 2: CASE ASSEMBLY
STEP 5
LEFT DRAWERS RIGHT DRAWERS
SET THE CASE UPRIGHT (FEET ON THE GROUND) THE CASE IS HEAVY, THIS MAY
REQUIRE (2) PEOPLE.
INSTALL THE DRAWERS BY PLACING THE WHEELS ON THE DRAWER BEHIND THE
WHEELS ON THE CABINET. PUSH THE DRAWER IN.
BE SURE THAT THE ASSEMBLED LEFT DRAWERS GO ON THE LEFT SIDE AND THE
ASSEMBLED RIGHT DRAWERS GO ON THE RIGHT SIDE. SEE FIGURE 4.
FIG. 4 - NOTE THAT THE DRAWER FRONT IS SLIGHTLY
OFF-CENTER ON THE DRAWER BOX, THIS IS INTENTIONAL.
ASSEMBLED LEFT DRAWER (x3) ASSEMBLED RIGHT DRAWER (x3)

11
FINAL ASSEMBLY
TO SECURE THE DRESSER TO THE WALL, PLEASE REFER TO THE
INSTRUCTIONS IN THE PROVIDED WALL STRAP KIT.
THE SLOT FOR ATTACHING THE WALL STRAP
IS LOCATED BEHIND THIS DRAWER

Warranty: This Delta product is warranted to be free from defects for a period
of 90 days from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Please do not return this item to the store before contacting
us about missing parts or with any questions.
Customer Service:
Web Site: www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
To register your product for important safety alerts and updates to
your product please visit http://deltaenterprise.com/register.asp
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
To report a problem, please log on to
www.deltachildrensproducts.com and click the Customer Service
Tab, or log on to www.deltaenterprise.com/customer_service.asp,
or contact us by phone at [phone].
Use the space below to make note of those numbers. They can be
found on the label on the back of the product.
Style No.:______________________
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)