Delta Childrens Products 74106 Series User manual

JUL 12,2011 21412-R5©2011DELTA ENTERPRISE CORP.
STYLE No: 74106-
COLOR FACTORY
REV
A
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product
please visit www.deltachildrensproducts.com and click on Product Registration.
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
Consumer Care:
www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
When contacting Delta Consumer Care you
will need to reference the above number.
SPRINGTIME 6 DRAWER DRESSER

2
PARTS: HARDWARE KITS PART #21413
WARNING:
Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:
.Place heaviest items in the lowest drawers.
.Unless specifically designed to accommodate, do not set TV’s or other heavy objects on the top of this
product.
.Never allow children to climb or hang on drawers, doors,or shelves.
.Never open more than one drawer at a time.
Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.
.Always monitor your child’s activity when in the nursery.
.Do not allow standing in drawers.
.Do not allow standing on top of this product.
.Accessory Items must be securely fastened to this product according to the instructions provided with
those items.
.To avoid head injury, do not allow children to play underneath open drawers.
.Do not leave drawers open when not in use.
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and
shape specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
C. CRESCENT
WASHER x8
A. 75mm BOLT x1 B. 30mm BOLT x4
D. 50mm BOLT x19 E. WOOD DOWEL x44 F. KNOB SCREW x12
G. SCREW x28 H. DRAWER SCREW x54
ALLEN WRENCH PHILLIPS SCREWDRIVER
NOT INCLUDED
K. KNOB x12
PART# 21377

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
3
L. Left side
Part# 21398
M. Right side
Part# 21399
U. Middle front rail x4
Part# 21405
R. Top front rail x1
Part# 21402
T. Bottom front rail x1
Part# 21404
P. Top back rail x1
Part# 21401
S. Bottom back rail x1
Part# 21403
N.Top panel x1
Part# 21400
X. Bottom
back panel x2
Part# 21916
W. Back panel x2
Part# 21407
V. Divider frame x1
Part# 21406
BB. Drawer front x4
Part# 21409
AA. Drawer front
Vein line x2
Part# 21408
DD. Drawer left
side x6
Part# 21392
CC. Drawer right
side x6
Part# 21391
EE. Drawer back x6
Part# 21410
FF. Drawer bottom x6
Part# 21411
GG. Drawer
support x6
Part# 21394

HARDWARE SYSTEM - REVIEW BEFORE ASSEMBLY
4
C. CRESCENT
WASHER
D. 50mm BOLT
INSERT THE DOWELS IN THE RAIL
INTO THE HOLES IN THE E POST.
INSERT THE BOLT INTO THE SLOT. TURN
CLOCKWISE WITH FINGERS OR THE ALLEN
WRENCH PROVIDED. DO NOT FULLY
TIGHTEN, LEAVE 1/2” (12mm) EXPOSED.
SLIDE THE CRESCENT WASHER OVER THE
EXPOSED BOLT, BEHIND THE HEAD OF THE
BOLT. TIGHTEN THE BOLT WITH THE ALLEN
WRENCH PROVIDED.
INSTALL (1) BOLT AND (1) CRESCENT WASHER
AT A TIME. TIGHTEN UNTIL IT LOOKS LIKE THE
PICTURE.

STEP 1:
5
STEP 2:
U
E. WOOD DOWEL x44
L
M
U
R
T
P
S
X
EE
E
E
E
E
L
ATTACH TOP FRONT RAIL (PART R), BOTTOM
FRONT RAIL (PART T), TOP BACK RAIL (PART P),
BOTTOM BACK RAIL (PART S) TO LEFT SIDE
(PART L). ENSURE THAT THE SLOTS ON THE
RAILS FACE THE INSIDE. USING (4) 50mm BOLT
(PART D) AND (4) CRESCENT WASHERS (PART
C). FOLLOW DIRECTION ON PAGE 4. TIGHTEN
ALL BOLTS WITH THE ALLEN WRENCH.
INSERT (2) MIDDLE FRONT RAIL (PART U) AND (1)
BOTTOM BACK PANEL (PART X) WITH THE
HOLES TO THE BACK AND FRONT OF LEFT SIDE
(PART L). R
P
T
S
X
D,
C
D,
C
D,
C
D,
C
C. CRESCENT
WASHER x4
D. 50mm BOLT x4

STEP 3:
6
STEP 4:
U
D. 50mm BOLT x3
A. 75mm BOLT x1
C. CRESCENT
WASHER x4
INSERT THE BOTTOM BACK PANEL (PART X) AND
THE (2) MIDDLE FRONT RAILS INTO THE DIVIDER
FRAME. CAREFULLY ALIGN ALL OF THE DOWELS
WITH THE HOLES IN THE RIGHT SIDE (PART M).
ATTACHED THE RIGHT SIDE USING (4) 50mm
BOLTS (PART D) AND (4) CRESCENT WASHER
(PART C) FOLLOWING THE DIRECTION ON PAGE
4. TIGHTEN ALL BOLTS WITH THE ALLEN
WRENCH.
D,
C
D,
C
D,
C
M
X
D. 50mm BOLT x4
D
D
A
VINSERT THE DIVIDER FRAME (PART V) INTO THE
(2) MIDDLE FRONT RAILS AND BOTTOM BACK
PANEL. CAREFULLY ALIGN ALL OF THE DOWELS
WITH THE HOLES IN THE DIVIDER FRAME. USING
(3) 50mm BOLTS (PART D) FOR FRONT, BACK TOP
RAIL AND FRONT BOTTOM RAIL. USING (1) 75mm
BOLT (PART A) FOR BACK BOTTOM RAIL.
TIGHTEN ALL BOLTS WITH THE ALLEN WRENCH.

STEP 5:
7
STEP 6:
G. SCREW x28
D. 50mm BOLT x8
B. 30mm BOLT x4
ATTACHED THE TOP PANEL (PART N) TO
THE BASE OF THE CASE FROM STEP 4.
ENSURE ALL DOWELS ARE ALIGNED
PROPERLY BEFORE INSTALLING ANY
BOLT. INSTAILL (8) 50mm BOLTS (PART
D) THROUGH THE TOP FRONT AND
BACK RAILS, THEN INSTALL (4) 30mm
BOLTS (PART B) THROUGH THE SIDES.
TIGHTEN ALL BOTLS WITH THE ALLEN
WRENCH.
N
D
D
B
B
W
W
G
ATTACH BACK PANELS (PART W)
USING (24) SCREWS (PART G).
TIGHTEN WITH A PHILLIPS
SCREWDRIVER.

STEP 7:
8
GG
FF
H
SLIDE DRAWER BOTTOM (PART FF)
INTO THE GROOVES. INSTALL THE
DRAWER SUPPORT (PART GG) USING
ON DRAWER SCREW (PART H)
EE
DD
CC
H
H
AA, BB
H
H
ATTACH THE RIGHT AND LEFT
DRAWER SIDES (PARTS DD AND
CC) TO THE DRAWER BACK
(PART EE) WITH (4) DRAWER
SCREWS (PART H). NOTE:
GROOVES IN BOTTOM MUST
ALIGN TIGHTEN WITH PHILLIPS
SCREWDRIVER
ATTACH THE DRAWER FRONT
(PARTS AA AND BB). USING (4)
DRAWER SCREWS (PART H). BE
SURE THE BOTTOM PANEL IS IN THE
GROOVE. TIGHTEN WITH THE
PHILLIPS SCREWDRIVER.
H. DRAWER SCREW x9

STEP 7: CONTINUED
9
STEP 8:
K
F
K. KNOB x12
6X
ATTACH (2) KNOBS (PART K)
WITH (2) KNOB SCREWS (PART
F). TIGHTEN WITH THE PHILLIPS
SCREWDRIVER.
INSTALL DRAWERS. REARRANGING THE
DRAWERS MAY RESULT IN A BETTER FIT
OR ALIGNMENT.
F. KNOB SCREW x12

STYLE No: 74106-
COLOR FACTORY
REV
A
Warranty: This Delta Case is warranted to be free from defects for
a period of 90 days from the date of purchase under normal use.
This warranty extends only to the original retail purchaser and is valid
only when supplied with proof of purchase, or if received as a gift,
when the registration is on file with Delta.
Consumer Care:
www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please visit www.deltachildrensproducts.com and click on Product Registration to
register your product for important safety alerts and updates.
For questions or comments, please log on to www.deltachildrensproducts.com and
click Consumer Care, or contact us by phone at [phone].
In the event that you need to contact our Consumer Care department please have the
Style Number and Lot Number available. If they are not printed below they can be found
on the label on the Back panel.
Use the space below to make note of those numbers.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)