Delta Childrens Products 75106 Series User manual

21738-R2, May 26,2011 ©2011 DELTA ENTERPRISE CORP.
STYLE No: 75106-
COLOR FACTORY
REV
A
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product
please visit www.deltachildrensproducts.com and click on Product Registration.
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
Consumer Care:
www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
When contacting Delta Consumer Care you
will need to reference the above number.
BENTLEY 6 DRAWER DRESSER

2
PARTS: HARDWARE KIT PART # 21737
WARNING:
Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:
.Place heaviest items in the lowest drawers.
.Unless specifically designed to accommodate, do not set TV’s or other heavy objects on the top of this
product.
.Never allow children to climb or hang on drawers, doors,or shelves.
.Never open more than one drawer at a time.
Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.
.Always monitor your child’s activity when in the nursery.
.Do not allow standing in drawers.
.Do not allow standing on top of this product.
.Accessory Items must be securely fastened to this product according to the instructions provided with
those items.
.To avoid head injury, do not allow children to play underneath open drawers.
.Do not leave drawers open when not in use.
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and
shape specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
KK. 30mm Wood
Dowel x46
LL. Plastic
Barrel Nut x24
MM. Plastic Crescent
Washer X 8
PP. Knob x6
Part# 21739
M5 BALL HEX
ALLEN WRENCH M4 BALL HEX
ALLEN WRENCH PHILLIPS
SCREWDRIVER
AA. 75mm Bolt x1
BB. 65mm Bolt x8
CC. 55mm Bolt x1 DD. 45mm Bolt x10 EE. 35mm Bolt x4
FF. 40mm Screw x24 GG. 30mm Screw x14 NN. 25mm Screw x30
HH. 15mm Back
Panel Screw x20
JJ. 25mm Knob
Screw x6

3
A. Left Side x1
Part# 21718
B. Right Side x1
Part# 21719
C. Divider
Frame x1
Part# 21720
D. Top Panel x1
Part# 21730
E. Back Bottom
Panel x2
Part# 21726
F. Front Top
Rail x1
Part# 21721
G. Front Bottom
Rail x1
Part# 21723
H. Back Top
Rail x1
Part# 21722
J. Back Bottom
Rail x1
Part# 21724
K. Front
Molding x1
Part# 21728
L. Middle Rail x4
Part# 21725
M. Back Top
Panel x2
Part# 217327
N. Side
Molding x2
Part# 21729
P. Drawer Front x6
Part# 21736
R. Drawer Back x6
Part# 21733
S. Drawer Left Side x6
Part# 21731
T. Drawer Right Side x6
Part# 21732
U. Drawer bottom x6
Part# 21734 V. Drawer Support x6
Part# 21735
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.

HARDWARE SYSTEM - REVIEW BEFORE ASSEMBLY
4
1. Install (1) 65mm Bolt into each threaded
insert by turning it ONLY (2) FULL TURNS.
Install all bolts in one side before continuing.
2. Align the bolt with the hole in the end of the rail,
align the dowels in the end of the rail with the with
the holes in the post. Slide together until tight.
3. Slide the Plastic Crescent Washer over the
exposed bolt, behind the head of the bolt. Tighten
the bolt with the M5 Allen Wrench provided.
Ensure all bolts are tightened.
Plastic Crescent Washer
65mm Bolt
x2

5
AB
C
E x2
F
G
H
J
STEP 1:
KK. WOOD DOWEL
30mm X46
STEP 2:
C
C
C
F
F
HH
G
G
J
J
CC CC
AA AA
DD
DD DD DD
Attach Top Front Rail (Part F) and Attach Top
Back Rail (Part H) to the Divider Frame (Part C)
using (2) 45mm Bolts (Part DD). Attach Bottom
Front Rail (Part G) to the Divider Frame (Part C)
using (1) 75mm Bolts (Part AA). Attach Bottom
Back Rail (Part J) to the Divider Frame (Part C)
using (1) 55mm Bolts (Part CC). Tighten all bolts
with the M4 Allen Wrench.
L x4
AA. 75mm Bolt x1
CC. 55mm Bolt x1
DD. 45mm Bolt x2
Install (46) 30mm Wood
Dowels as shown.
NOTE:Slots face inside

6
STEP 3:
MM. Plastic Crescent Washer X4
A
E
L
STEP 4:
Repeat Step 3 using the Right Side (Part B).
Refer to Page 4 to install the 65mm Bolt and Plastic
Crescent Washer.
B
E
L
BB, MM
BB. 65mm Bolt x4
MM. Plastic Crescent
Washer X4
BB. 65mm Bolt x4
BB, MM
BB, MM
BB, MM
Insert the Bottom Back Panel (Part E) and the
(2) Middle Front Rails (Part L) into the Divider
Frame. Carefully align all of the dowels (check
to confirm they are still installed) with the holes
in the Left Side (Part A). Attached the Left Side
using (4) 65mm Bolts (Part BB) and (4) Plastic
Crescent Washers (Part C) following the
directions on page 4. Tighten all bolts with the
M5 ball Allen Wrench.

7
STEP 5:
STEP 6:
KN
N
GG GG
Attach the Bottom Front Molding (Part K) to the front of
the case using (8) 30mm Screws, ensure the screws go
into the predrilled holes in the molding. Tighten with a
Phillips screwdriver. Next attach the (2) Bottom Side
Moldings (Part N) to the case using (3) 30mm screws
for each, ensure the screws go into the predrilled holes
in the molding.
D
DD
DD EE
Attach the Top Panel (Part D) to
the case. Ensure (2) Dowels from
the side are aligned properly
before installing any bolts. Install
(8) 45mm bolts (Part DD) through
the Top Front and Back Rails, then
install (4) 35mm Bolts (Part EE)
through the sides. Tighten all bolts
with the M4 Allen Wrench.
GG. 30mm Screw x14
DD. 45mm Bolt x8
EACH SIDE
EE. 35mm Bolt x4

M
M
HH
8
STEP 7:
STEP 8:
Attach (2) Back Panels
(Part M) using (20) Back
Panel Screws (Part HH).
Tighten with a Phillips
Screwdriver.
LL. Plastic Barrel
Nut x24
R
S
T
FF
FF
LL
LL
1. Attach the Right and Left Drawer Sides (Parts
S and T) to the Drawer Back (Part RR) with (4)
40mm Screws (Part FF) and (4) Plastic Barrel
Nuts (Part LL). Note: grooves in bottom must
align. Tighten with Phillips Screwdriver.
NN
U
V
P
NN NN
2. Slide drawer bottom
(part u) into the grooves.
Install the Drawer
Support (Part V) using
(1) 25mm Screw (Part
NN). Tighten with the
Phillips Screwdriver. 3. Attach the Drawer Front (Part P).
Using (4) 25mm Screws (Part NN).
Be sure the bottom panel is in the
groove. Tighten with the Phillips
Screwdriver.
HH. 15 mm Back
Panel Screw x20
FF. 40mm Screw x24 NN. 25mm Screw x30

9
STEP 8: continued
PP. Knob x6
X6
PP
JJ
Attach (1) Knob (Part
PP) with (1) Knob
Screw (Part JJ).
Tighten with the
Phillips Screwdriver.
JJ. 25mm Knob
Screw x6
Install the drawers. Changing the drawer position
may improve operation and alignment.
Install Tip-over restraint, see instructions with kit.

STYLE No: 75106-
COLOR FACTORY
REV
A
Warranty: This Delta Case is warranted to be free from defects for
a period of 90 days from the date of purchase under normal use.
This warranty extends only to the original retail purchaser and is valid
only when supplied with proof of purchase, or if received as a gift,
when the registration is on file with Delta.
Consumer Care:
www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please visit www.deltachildrensproducts.com and click on Product Registration to
register your product for important safety alerts and updates.
For questions or comments, please log on to www.deltachildrensproducts.com and
click Consumer Care, or contact us by phone at [phone].
In the event that you need to contact our Consumer Care department please have the
Style Number and Lot Number available. If they are not printed below they can be found
on the label on the Back panel.
Use the space below to make note of those numbers.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)