Delta Electronics Power Output Module DVPPS01 User manual

http://www.delta.com.tw/products/plc.asp
DVPPS01
DVPPS02 POWER OUTPUT MODULE
1 Warning
This instruction will be helpful in the installation, electronic specification, function specification and troubleshooting of the DVPPS01 and
DVPPS02.
This is an OPEN TYPE DVPPS series. The DVPPS series should be kept in an enclosure away from airborne dust, high humidity,
electric shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the enclosure,
so as to avoid the hazard to users and the damage to the DVPPS series.
Never connect the AC main circuit power supply to any of the output terminals, as it will damage the DVPPS series. Check all the wiring
prior to power up. To avoid any electromagnetic noise, make sure the DVPPS series is properly grounded .
2 Introduction
2.1 Model Explanation
Thank you for choosing DELTA DVP series. DVPPS series is a power module with 2 types that sorted by output circuit. 1. PS01 provides
24VDC and 1A current for output power. 2. PS02 provides 24VDC and 2A current for output power. DVPPS series is only used for Delta DVP
series. DVPPS series is separated from the PLC MPU for better space utilization and easier installation.
PS01
Nameplate Explanation
Model
Input Power Supply Spec.
Output Module Spec.
Barcode and Serial Number
MODEL : DVPPS01
INPUT : 100~240VAC 50 / 60Hz
OUTPUT : 24Vdc 1.0A
PS01 0T4360001
PS02
Model
Input Power Supply Spec.
Output Module Spec.
Barcode and Serial Number
MODEL : DVPPS02
INPUT : 100~240VAC 50 / 60Hz
OUTPUT : 24Vdc 2.0A
PS02 0T4370001
Model Name
Series name
Power module
Output current
Serial Number
Production number
Production weeks
Production year (2004)
Production factory
Version
Production model
2.2 Product Profile and Outline
PS01
390
13.3 60
36.5
DVPPS01
1
2
33
4
5
6
Unit: mm
PS02
13.3 60
100
32.5
90
55
33
DVPPS02
1
2
33
4
5
6
7
7
Unit: mm
1 Power LED 1 Power LED
2 Output/input terminal (fixed terminal) 2 Output/input terminal (fixed terminal)
3 DIN rail clip 3 DIN rail clip
4 DIN rail track (35mm) 4 DIN rail track (35mm)
5 I/O terminal label 5 I/O terminal label
6 Nameplate 6 Nameplate
7 Mounting holes

3 Function/Electrical Specification
Model
Item DVPPS01 DVPPS02
Power Input 100~240 VAC (-15%~+10%), 50 / 60 Hz 100~240 VAC (-15%~+10%), 50 / 60 Hz
Output Power 24VDC (±3%), output current: 1A max. 24VDC (±3%), output current: 2A max.
Ripple & Noise Under 100mVp-p Typical at full load Under 240mVp-p Typical at full load
Efficiency 78%~87% Typical at full load
Over Load / Short Circuit Protection Auto Recovery
Grounding The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and N
(All PLC units should be grounded directly to the ground pole).
Operation/Storage Environment Operation: 0℃~55℃(Temperature), 50~95% (Humidity), Pollution degree 2;
Storage: -25℃~70℃(Temperature), 5~95% (Humidity)
Agency Approvals Underwriters Laboratories, Inc.: UL508 Listed (Industrial Control Equipment)
European Community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC
Weight (g) 158 250
4 Installation and Wiring
4.1 Mounting Arrangements and Wiring
■DIN Rail Installation
The DVPPS can be secured to a cabinet by using the DIN rail that is 35mm
high with a depth of 7.5mm. When mounting the DVPPS on the DIN rail, be
sure to use the end bracket to stop any side-to-side motion of the DVPPS,
thus to reduce the chance of the wires being pulled loose. On the bottom of
the DVPPS is a small retaining clip. To secure the DVPPS to the DIN rail,
place it onto the rail and gently push up on the clip. To remove it, pull down
on the retaining clip and gently pull the DVPPS away from the DIN rail.
Please see the figure on the right:
For heat dissipation. Make sure to
provide a minimum clearance of
50mm between the unit and all
sides of the cabinet. (as shown
below)
DVP MPU
> 50mm> 50 mm
> 50mm
> 50mm
■Direct mounting: Tighten M4 screws into direct mount hole.
■Wiring
To suit M3.5 screw terminals
Below 6.2
Below 6.2
Notes:
1. Please use O-type or Y-type terminals for I/O wiring terminals. The specification for the terminals is
as shown on the left. Tighten PLC terminal screws to a torque of 5~8 kg-cm (4.3~6.9 in-lbs).
2. Please avoid tiny metal material enter DVPPS01/PS02 when screwing and wiring. After finishing
wire, remove the affix that pasted on the heat sink for heat dissipation.
3. Use Copper Conductors Only, 60℃.
4.2 Wiring Notes
■Environment
1. DO NOT store the DVPPS01/PS02 in a dusty, smoky, or corrosive atmosphere.
2. DO NOT store the DVPPS01/PS02 in an environment with high temperature or high humidity.
3. DO NOT install PLC on a shelf or on an unstable surface.
■Power Input Wiring
Power input of DVPPS01/PS02 is AC input; following items should be noticed:
1. Connect the AC input (100VAC ~ 240VAC) to terminals L and N. Any AC110V or AC220V connected to the +24V terminal will
permanently damage the DVPPS01/PS02.
2. Please use wires of 1.6mm and above for the grounding.
3. If the power-cut time is less than 10ms, the DVPPS01/PS02 still operates unaffectedly. If the power-cut time is too long, the
DVPPS01/PS02 will stop operating and all the outputs will be Off.
5 Trial Run
☼Power indicator, Running and Test
The “POWER” LED at the front of DVPPS01/PS02 will be lit (in green) if the power is on. If the indicator is not ON, it indicates that the
power supply is not enough or short circuit. Please check your power wiring.
6 Troubleshooting
Judge the errors by the indicators on the front panel. When errors occurred on DVPPS01/PS02, please check:
☼「POWER」LED
The “POWER” LED at the front of the MPU will be lit (in green) if the power is on. If the indicator is not on when the MPU is powered up,
please check if power supply is normal. If the indicator is not on when the MPU is powered up and with the input power being normal, it is
an indication that the PLC is malfunction. Please have this machine replaced or have it repaired at a dealer near you.