Delta Regis ESB6-8 User manual

18VDC ESB6 Series
Cordless Screwdrivers
Operation Manual
DELTA REGIS
Tools Inc.
CAUTION - Please read, understand, and follow all operating and safety instructions in
this manual before using the tools.
The 18VDC ESB6 Series Cordless Electric Screwdrivers are designed for exclusive use
with specic Delta Regis batteries and battery chargers as dened in this manual. Do not
attempt to use the tools, batteries and/or battery chargers with any products other than
as specied in this manual.
If you have any questions or concerns, please contact us at:
Delta Regis Tools, Inc.
3315 Industrial 25th St.
Ft. Pierce FL 34946
USA
Ph [phone]
Fx [phone]
E-mail: [email protected]
Website: www.deltaregis.com
Doc. 18V_ESB6_Series_Manual_R0
Copyright © 2014 Delta Regis Tools, Inc
Screwdriver Models : ESB6-8, ESB6-12, ESB6-15, ESB6-22

18V ESB6 Series
Operation Manual
DELTA REGIS
Tools Inc.
www.deltaregis.com
Important - Installation and Safety
1. Please read and understand the operation manual and follow all safety and operation instructions.
2. Use these products in a suitable dry, indoor location. Do not use the tools, batteries and/or battery chargers in
damp, wet or high temperature environments. Do not use in the presence of ammable liquids or gases.
3. Ensure that the battery charger has proper ventilation. Do not expose the tools, batteries and/or battery
chargers to areas subject to airborne contaminants (eg. dust, metal lings).
4. Use only a properly grounded electrical outlet of the correct supply voltage to power the battery charger. Ensure
that the supply outlet is overload protected and of sucient amperage capacity.
5. Use only the correct plug for the battery charger. Hold the plug of the power cord when connecting or
disconnecting. Do not pull on the cable.
6. Do not expose the tool, battery, battery charger or power cord to oil, chemicals, or heat. Ensure that the power
cord is routed and used in such a manner as to not be subject to sharp objects that may abrade or cut the cable.
7. Locate the battery charger in a suitable, safe location on a steady surface. Do not place in a high location where
there may be a risk of it falling. Secure the battery charger in position to prevent possible movement caused by
pulling on the power cord.
8. Do not cover the battery charger or stack any objects on top of or near the battery charger. Ensure that
adequate clearance and ventilation is provided around the perimeter of the battery charger.
9. The ‘ESB-CHG’ series battery chargers are for use exclusively with Delta Regis brand 18VDC‘ESB-18VL’ series
lithium-ion batteries as specied on the following pages. Use of the battery charger (or battery) with any
product not specied in this manual may result in malfunction, damage, or injury.
10. In the event that the battery charger is overloaded beyond the maximum current rating, an internal fuse will
disrupt power. Should the battery charger stop functioning, or exhibit abnormal or intermittent operation,
please discontinue use immediately and send the battery charger to an authorized service center for
troubleshooting and repair.
11. Excessive duty cycle will cause the tool to overheat. If this occurs, discontinue use until cooled down and reduce
cycle rate. As a general rule, do not exceed 10-15 fasteners/minute.
12. The ‘ESB6’ Series cordless screwdrivers incorporate a protection circuit which stops the electric screwdriver if the
tool is switched from forward to reverse while running. Should this happen, the operator must release the tool
trigger and restart the fastening cycle.
13. Unplug the battery charger if it is not being used on a regular basis.
14. Do not attempt to disassemble or repair the screwdriver, battery or battery charger. Repairs should only be
performed by qualied technicians properly trained in the safe operation, troubleshooting, and repair of these
devices. Please consult Delta Regis for the location of the nearest service center.
15. Use only the factory specied Delta Regis brand replacement parts and accessories with these tools.
16. Any damage to the tool, battery and/or battery charger resulting from misuse, abuse, or failure to follow these
guidelines will void the limited product warranty.
CAUTION: To prevent injury, use of the included side handle accessory and a proper grip are required due to the torque reaction
generated by these cordless electric screwdrivers models.
Warning - Failure to understand and follow proper installation guidelines, safety requirements, and
operating instructions may result in malfunction, component damage, property damage, shock hazard,
re hazard, injury or death.
Grounding - The battery charger (and AC power cord) is equipped with a 3-prong electrical receptacle/
plug with ground pin. The charger must be connected to a properly grounded AC electrical outlet. Do not
attempt to use this charger without a properly functioning ground connection. Never connect a live circuit
to the ground pin or internal yellow-green ground wire.
Page 2

18V ESB6 Series
Operation Manual
DELTA REGIS
Tools Inc.
www.deltaregis.com Page 3
Model Numbers and Specifications
Model Number Range Nm Range In-lbs
Speed (RPM)
Hi / Lo
Dimensions (mm)
Length x Height Weight (kg)
Applicable Batteries / Chargers
(sold separately, see below)
Models with internal torque adjustment
ESB6-8 4 - 8 36 - 70 1200 / 750 214 x 197
(less battery)
1.0
(less battery)
Batteries (1.5 or 3Ah):
ESB-18VL1500 (ESB6-8,12)
ESB-18VL3000 (ESB6-8,12,15,22)
Battery Chargers:
ESB-CHG80 or ESB-CHG120
ESB6-12 6 - 12 53 - 106 720 / 500
ESB6-15 4 - 15 36 - 132 600 / 380 224 x 200
(less battery)
1.2
(less battery)
ESB6-22 8 - 22 70 - 194 350 / 200
*Standard model number is for tool with 1/4” hex bit holder. Add sux‘SQ’ for 3/8”square drive (eg. ESB6-15SQ)
18V Li-Ion Battery
Model Number
Rating
(mAh)
Approx.
Rundowns
(Full Charge)
Charge Time
(80% / Full Charge)
Dim (mm)
L x W x H
Weight
(g)
ESB-18VL1500 1500 3000 20 / 30 min. 119 x 90 x 40 430
ESB-18VL3000 3000 6000 40 / 60 min. 170 x 160 x 80 1068
Battery
Charger Input Output Use to charge battery model
Dim (mm)
L x W x H
Weight
(g)
ESB-CHG80 90-240 VAC
50/60 Hz
21VDC, 3.2A ESB-18VL1500, ESB18VL3000 115 x 145 x 80 530
ESB-CHG120** 21VDC, 3.0-4.5A ESB-18VL1500, ESB-18VL3000 170 x 160 x 80 1068
ESB-CHG80 shipped with standard North American cord set. For EU cord, add sux ‘E’; for UK cord add sux ‘UK’ to part number.
**Premium charger model ESB-CHG120 has a built-in cooling fan and an LCD display which shows Charge Time, Cell Temperature, Battery
Voltage, Recharge Status and Battery ID verication.
18VDC Cordless Electric Screwdrivers (CE / RoHS)
18V Lithium Ion Batteries
Battery Chargers
ESB-CHG120
(sold separately)
ESB-18VL1500
(sold separately)
Item Quantity
Chuck Key 1
Belt Hook 1
Screw for Belt Hook 1
Suspension Bail 1
Philips Power Bit (hex models) 2
1/4” Hex -> 3/8” Sq Adapter
(hex models)
1
Side Handle 1
Side Handle Collar 1
Bolt for Side Handle 1
Torque ID Ring 4
Included Accessories
ESB-18VL3000
(sold separately)

18V ESB6 Series
Operation Manual
DELTA REGIS
Tools Inc.
www.deltaregis.com Page 4
Quick Set-up and Operation Overview
Setting the Torque
The ESB6 Series feature internal torque adjustment located inside the side cover of the
screwdriver and is used to set the output torque of the driver (FIG. 1).
WARNING! FWD/REV SWITCH MUST BE IN THE ‘OFF’POSITION AND/OR BATTERY MUST BE REMOVED BEFORE
ADJUSTING THE TORQUE.
Slide the cover left to expose the adjustment point. Insert the chuck key into the
bit holder and turn until the adjustment keyway is accessible (FIG. 2). Remove the
chuck key from the bit holder and insert into the adjustment keyway; some force will
be required (FIG. 3). Turn the chuck key clockwise to increase torque output, ccw to
decrease torque output. Once the adjustment has been made, remove the chuck key
and close the side cover.
WARNING! DO NOT OPERATE THE SCREWDRIVER WITH CHUCK KEY INSTALLED. ACCESS COVER MUST BE
CLOSED DURING OPERATION.
We recommend the use of an appropriate torque tester and static joint testing after
adjustment to verify proper torque settings. Make adjustments through a series of
gradual increases, starting below the desired torque and working upwards. Once the
desired torque setting is achieved, you may install a colored ring to indicate torque.
This will help visually identify low, medium and high torque settings.
The output torque of the screwdriver should be veried at regular intervals. The
frequency of verication will depend on the individual user’s quality control
requirements. There may be an initial drop in output torque during the break-in
period of the screwdriver.
1. Fully charge the battery using the battery charger before rst use to achieve
maximum fastening cycles.
2. Ensure that the screwdriver’s FWD/REV switch is ‘OFF’.
3. Insert the desired driver bit into the quick change chuck of the screwdriver by
pushing (or pulling, depending on model) the outer sleeve of the bit holder to
release the retainer. Verify that the bit is locked properly in
position after installing.
4. Switch the FWD/REV switch to the appropriate direction.
Select the desired speed (Hi/Lo) via the switch on the top of
the screwdriver.
5. Grip the screwdriver so that the index nger is comfortably
over the trigger mechanism. Hold securely to prevent the screwdriver from
rotating in your hand during use.
6. Align the driver bit properly in the head of the fastener. Keeping the driver in-line
with the fastener, pull and hold the start trigger - the screwdriver will install the
fastener (FWD). When the preset torque is reached, the clutch will activate and the
tool will shut-o. Once the tool shuts o, release the trigger to reset. To stop the
screwdriver before the fastening is complete, release the start trigger.
7. To remove a fastener, change the FWD/REV switch to the REV position.
Pull the start trigger to run the driver in reverse (CCW). Do not change
the position of the FWD/REV switch while the tool is running.
FIG. 1
FIG. 2
FIG. 3
Tool shown without
side handle for clarity.
On higher torque
applications, always install
the side handle and grip
the tool rmly with both
hands to react torque.

www.deltaregis.com
Battery Installation / Removal
Page 5
18V ESB6 Series
Operation Manual
DELTA REGIS
Tools Inc.
Internal Torque Adjustment
Slide open cover, insert chuck
key, turn CW to increase torque
setting, CCW to decrease torque
output. A torque meter will be
needed to verify torque setting.
Start Trigger
Pull to start the screwdriver and
hold until the driver shuts o
(CW tightening).
Torque ID Ring
Colored ring to help visually
indicate tools capacity or torque
setting.
FWD/REV Switch
Select the desired direction of
rotation for the screwdriver -
FWD (CW) or REV (CCW).
Center position is‘OFF’.
Wrist Strap
Helps to prevent the tool from
accidently being dropped.
Belt Hook
Mounting location on left and
right for the included belt hook.
Bit / Socket Holder
Pull sleeve to insert/remove
bits. Once the bit is inserted,
release the sleeve and pull
back and forth on the bit
to verify proper retention.
If square drive, press socket
onto drive.
LED Light
Illuminates dark
work areas
Hi/Lo Speed
Switch from high to
low speed
Features Overview
Insert the battery into the driver as shown. When
installed properly the driver will emit a short
beep and the LEDs will illuminate momentarily.
If the battery is installed incorrectly or too slowly
the driver will emit short beeps and the LEDs will
ash continuously. If this happens, remove the
battery and try again.
To remove the battery, depress the battery
release button and slide the battery away from
the driver.
Rundown / Battery Indicator
See page 7 for information

18V ESB6 Series
Operation Manual
DELTA REGIS
Tools Inc.
www.deltaregis.com Page 6
Inserting / Removing Power Bits
Installing / Removing Torque ID Ring (Optional)
Once the desired torque setting is achieved, remove the Torque ID ring by inserting a at head screwdriver
under the ring (FIG. 1) and pry away from the driver (FIG. 2). Install the new colored ring by pressing it onto the
tool until it clicks. This will help identify torque capacity or torque setting of the driver.
Insert the desired driver bit into the quick change chuck of the screwdriver by pulling the outer sleeve of the bit
holder to release the retainer. Verify that the bit is locked properly in position after installing. Please note, only
use 1/4” hex power bits. The use of insert bits will cause the bit to become lodged in the drive shaft. If insert bits
must be used, please select an appropriate 1/4”hex bit holder. If using 3/8” square drive, press socket onto drive.
FIG. 1 FIG. 2

www.deltaregis.com
Rundown Status Indicator
When the driver reaches the set torque and clutches out it will emit a short beep and the green rundown LED will
ash once indicating an OK rundown. If the driver does not clutch out before the operator releases the trigger
the driver will emit a long beep and the red rundown LED will ash once indicating a NG rundown.
Battery Status Indicator
The ESB6 Series Cordless Screwdrivers are programmed to avoid poor performance if the battery charge gets too
low. When the available battery power reaches 20%, the tool will continue to function and the red battery LED
will ash accompanied by several short beeps. When the battery reaches 10% charge, the red battery LED will
illuminate for a few seconds accompanied by several beeps. The driver will stop functioning. At this point remove
and replace the discharged battery with a fully charged battery to continue production.
LEDs / Buzzer
The supplied side handle improves ergonomics for higher torque ranges by allowing two handed operation.
Slide the side handle collar over the front of the tool until it clicks into place. Insert the bolt into the right side of
the collar. While holding the bolt in the collar with one hand screw the side handle onto the bolt until tight.
CAUTION: To prevent injury, use of the included side handle accessory and a proper grip are required due to the torque reaction
generated by these cordless electric screwdrivers models.
Side Handle Installation
Page 7
18V ESB6 Series
Operation Manual
DELTA REGIS
Tools Inc.
Battery LED (Red)NG Rundown LED (Red)OK Rundown LED (Green)

www.deltaregis.com Page 8
18V ESB6 Series
Operation Manual
DELTA REGIS
Tools Inc.
If you require parts or accessories for your Delta Regis product, please refer to our website or contact us for
further information.
Parts and Accessories
The ESB6 Series cordless electric screwdrivers, batteries and battery chargers are not user serviceable. Any
repairs must be performed by a Delta Regis authorized service center. Please consult Delta Regis Tools for further
information and the location of the nearest authorized service center.
Repairs to the ESB6 Series cordless electric screwdrivers, batteries and battery chargers must be performed by
trained personnel, knowledgeable and qualied in the repair of DC electric screwdrivers.
Use only genuine Delta Regis parts when servicing these products.
Do not attempt to modify the tools, batteries or battery chargers.
Service
Warranty
The ESB6 Series cordless electric screwdrivers, batteries and battery chargers are warranted for one year from
the date of purchase against defects in material and workmanship. In addition, the brushless motor in the ESB6
Series cordless screwdrivers is warranted for three years from the date of purchase against defects in material and
workmanship. This warranty does not cover damage due to transportation, abuse, misuse, or improper service.
Our sole remedy is to repair or replace (at our discretion) any unit found to be defective due to defects in material
or workmanship. It is the responsibility of the user to return any product thought to be defective, freight prepaid,
to our warehouse for inspection and evaluation.
There is no warranty of merchantability or tness of purpose. In no event will Delta Regis Tools, Inc.
be liable for business interruptions, loss of prots, harm, injury, damage, personal injury, cost of delay,
or any other special, indirect, incidental, or consequential losses, costs, or damages.