Delta Glider N Ottoman User manual

Style #:
Lot:
Date:
___________
___________
___________
APRIL 23, 2012, 23338, R0 ©2012 DELTA ENTERPRISE CORP.
A
Glider N Ottoman
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the bottom of
Glider Seat.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.

2
FABRIC CARE INSTRUCTIONS:
- Spot clean only.
- Clean spots as soon as they occur with a fabric safe cleaning product.
- Follow all warnings and instructions on any cleaning product used.
- DO NOT use bleach.
- Use only lint free cloths.
- Air dry - DO NOT place in sun.
- Machine washing is not recommended.
Wood:
- DO NOT scratch or chip the finish.
- Inspect periodically, contact Delta Children’s Products for replacement parts or questions.
- DO NOT store any parts in extreme temperatures and conditions such as a hot attic or a damp, cold
basement. These extremes can cause a loss of structural integrity.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-DO NOT use abrasive chemicals.
-DO NOT spray cleaners onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

3
B. Left Glider Arm x 1
C. Right Glider Arm x 1
D. Glider Base x 1
E. Glider Seat x 1 F. Left Glider Arm
Cushion x 1
H. Glider Seat
Cushion x 1
J. Ottoman Base x 1
N. 1/4” x 2-1/2” Bolt x 2
M. 1/4” x 1-3/8” Bolt x 20
P. 1/4” x 1/2” Barrel Nut x 2
M4 Allen Wrench
Supplied
L. Bottom Glides x 4
G. Right Glider Arm
Cushion x 1
K. Ottoman Cushion x 1
(not supplied)
Flat Head Screwdriver
No drills necessary. Do not
use power screwdriver.
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. Glider Back Frame x 1
Part # 23328
Part # 23329
Part # 23330
Part # 23331
Part # 23332
Part # 23333 Part # 23334 Part # 23335
Part # 23336 Part # 23337
Part # 5532
HARDWARE KIT IS PART # 22289 FOR COLOR 646 OR #22290 FOR
COLOR 266 OR #22291 FOR COLOR 296. SEE FRONT COVER.
Part # 5526
Part # 5530 Part # 5528
Part # 1177

4
Step 1
Parts and tools required to complete step.
Section 1: Glider Assembly
L
Turn the Glider Seat Base (Part D) over, then attach the Bottom Glides (Part L) as shown.
Remove the blacking strip from one glide at a time and adhere the glide to the base, repeat for all
4 glides.
L
L
L
D
D. Glider Base x 1
L. Bottom Glides x 4

5
Step 2
Parts and tools required to complete step.
Section 1: Glider Assembly
Attach the Glider Back Frame (Part A) to the Glider Seat (Part E) using (4) 1/4” x 1-3/8” Bolts
(Part M), Tighten with the M4 Allen Wrench.
A
E. Glider Seat x 1
A. Glider Back Frame x 1
M. 1/4” x 1-3/8” Bolt x 4
M4 Allen Wrench
Supplied
E
M
M

6
Step 3
Parts and tools required to complete step.
Section 1: Glider Assembly
Attach the Left Glider Arm (Part B) and the Right Glider Arm (Part C)
to the Glider Seat using (2) 1/4” x 1-3/8” Bolts (Part M) each (Figure A).
Do not tighten bolts. Install a Barrel Nut (Part P) in the hole at the
back of each arm (Figure B). Install (2) 1/4” x 2-1/2” Bolts
(Part N) as shown in Figure C. Tighten all bolts with
the M4 Allen Wrench. Use the Flat Head Screwdriver
to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench
Supplied
From Step 2
B. Left Glider Arm x 1
C. Right Glider Arm x 1
N. 1/4” x 2-1/2” Bolt x 2
P. 1/4” x 1/2” Barrel Nut x 2
M. 1/4” x 1-3/8” Bolt x 4
C
B
E
FIGURE A
C
B
FIGURE B
FIGURE C
A
A
E
P
N
N
A
B
C
E
M
M

7
Step 4
Parts and tools required to complete step.
Section 1: Glider Assembly
Attach the assembly from step 3 to the Glider Base (Part D) using (8) 1/4” x 1-3/8” Bolts (Part M) as
shown in Figure A & B. Tighten with the M4 Allen Wrench.
M. 1/4” x 1-3/8” Bolt x 8
M4 Allen Wrench
Supplied
FIGURE A
FIGURE B
E
D
M
D
E
M
From Step 3
D. Glider Base x 1

8
Step 5
Parts and tools required to complete step.
Section 1: Glider Assembly
Attach (1) Left Glider Arm Cushion (Part F) to the Left Glider Arm with the snaps on the Glider
Arm Cushion facing up, slide the Glider Arm Cushion under the Glider Arm and snap all (3) snaps
into place. Fold the Glider Arm Cushion at the bottom of the Glider Arm Pad to the Glider Seat.
Repeat on the other Glider Arm.
From Step 4
F. Left Glider Arm
Cushion x 1
G. Right Glider Arm
Cushion x 1
G
F
C B
LEFT
RIGHT
G
F
F
G
1
2
3

9
Step 6
Parts and tools required to complete step.
Section 1: Glider Assembly
Attach the Glider Seat Cushion (Part H) into the Glider as shown.
From Step 5
H
H. Glider Seat
Cushion x 1

10
Step 1
Parts and tools required to complete step.
Section 2: Ottoman Assembly
Attach the Ottoman Cushion (Part K) to the Ottoman Base (Part J) using (4) 1/4” x 1-3/8” Bolts
(Part M), Tighten with the M4 Allen Wrench.
J
K
M
M
M
J. Ottoman Base x 1 K. Ottoman Cushion x 1
M. 1/4” x 1-3/8” Bolt x 4
M4 Allen Wrench
Supplied