Delta DRP048V060W1B Series Instruction Manual

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
1
Highlights & Features
•Universal AC input voltage range
•Power will not de-rate for the entire input voltage range
•Power Boost of 150% for 5 seconds
•Full corrosion resistant aluminium casing
•Conforms to harmonic current IEC/EN 61000-3-2, Class A
•Extreme low temperature cold start at -40°C
•Conformal coating on PCBAs to protect against common
dust and chemical pollutants
•Hazardous Locations approval to ATEX and Class I, Div 2
(DRP048V060W1BA)
•Certified according to IEC/EN/UL 62368-1
Safety Standards
CB Certified for worldwide use
Model Number: DRP048V060W1B
Unit Weight: 0.38 kg (0.84 lb)
Dimensions (L x W x D): 121 x 32 x 125 mm
(4.76 x 1.26 x 4.92 inch)
General Description
The CliQ II DIN rail power supply series from one of the world’s leading power supply companies, Delta Electronics Group, offers output
voltage of 48 V. These products are encased in rugged yet lightweight full aluminium body that can withstand shock and vibration
according to IEC 60068-2 standard. The series of single phase products can operate over a wide temperature range of -25°C to +80°C.
These products also feature universal AC input voltage range from 85 Vac to 264 Vac and the power will not de-rate throughout the entire
range. Another great feature is the conformal coating on the PCBA which allows selected models to be certified to ATEX and Class I, Div
2 for use in hazardous locations. The design conforms to harmonic current emission IEC/EN 61000-3-2, Class A.
Model Information
CliQ II DIN Rail Power Supply
Model Number Input Voltage Range Rated Output V oltage Rated Output Curr ent
DRP048V060W1B85-264 Vac (120-375 Vdc) 48 Vdc 1.25 A
Model Numbering
DR P048V
060W
1
B

DIN Rail Power Supply Output Voltage Output Power Single Phase CliQ II Series A - Metal Case,
with Class I, Div 2
N - Metal Case,
without Class I, Div 2

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
2
Specifications
Input Ratings / Characteristics
Nominal Input Voltage 100-240 Vac
Input Voltage Range 85-264 Vac
Nominal Input Frequency 50-60 Hz
Input Frequency Range 47-63 Hz
DC Input Voltage Range* 120-375 Vdc
Input Current < 1.40 A @ 115 Vac, < 0.80 A @ 230 Vac
Efficiency at 100% Load > 91.0% @ 115 Vac, > 92.0% @ 230 Vac
Max Power Dissipation 0% load < 0.5 W @ 115 Vac & 230 Vac
100% load < 5.9 W @ 115 Vac, < 5.2 W @ 230 Vac
Max Inrush Current (Cold Start) < 20 A @ 115 Vac, < 35 A @ 230 Vac
Leakage Current < 1 mA @ 240 Vac
*Fulfills the test conditions for this range.
Output Ratings / Characteristics**
Nominal Output Voltage 48 Vdc
Factory Set Point Tolerance 48 Vdc ± 1%
Output Voltage Adjustment Range 48-56 Vdc
Output Current 1.25 A (continuously operating at 48 V)
1.875 A (Power Boost for 5 seconds at 48 V, refer to the
details in the Functions section)
Output Power 60 W (continuously operating at 48 V)
90 W (Power Boost for 5 seconds at 48 V
, refer to the details in
the Functions section)
Line Regulation < 0.5% (@ 85-264 Vac input, 100% load)
Load Regulation < 1.0% (@ 85-264 Vac input, 0-100% load)
PARD*** (20 MHz) < 200 mVpp
Rise Time
< 100 ms @ nominal input (100% load)
Start-up Time < 1,500 ms @ nominal input (100% load)
Hold-up Time > 20 ms @ 115 Vac,
> 125 ms @ 230 Vac (100% load)
Dynamic Response
(Overshoot & Undershoot O/P Voltage)
± 2% @ 85-264 Vac input, 0-100% load
(Slew Rate: 0.1 A/μs, 50% duty cycle @ 5 Hz)
Start-up with Capacitive Loads 5,000 µF Max
**For power de-rating from 50°C to 80°C, see power de-rating on page 3.
***PARD is measured with an AC coupling mode, 5cm wires, and in parallel with 0.1 μF ceramic capacitor & 47 μF electrolytic capacitor.

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
3
Mechanical
Case Cover / Chassis
Aluminium
Dimensions (L x W x D) 121 x 32 x 125 mm (4.76 x 1.26 x 4.92 inch)
Unit Weight 0.38 kg (0.84 lb)
Indicator Green LED DC OK
Cooling System Convection
Terminal Input 3 Pins (Rated 300 V/15 A)
Output 2 Pins (Rated 300 V/15 A)
Wire Input / Output AWG 20-12
Mounting Rail Standard TS35 DIN Rail in accordance with EN 60715
Noise (1 Meter from power supply) Sound Pressure Level (SPL) < 40 dBA
Environment
Surrounding Air Temperature
Operating
-25°C to +80°C (Cold Start at -40°C)
Storage -40°C to +85°C
Power De-rating Vertical Mounting > 50°C de-rate power by 2.5% / °C
Horizontal Mounting > 50°C de-rate power by 2.5% / °C
Operating Humidity 5 to 95% RH (Non-Condensing)
Operating Altitude 0 to 2,500 Meters (8,200 ft.)
Shock Test Non-Operating IEC 60068-2-27, 30 G (300 m/S²) for a duration of 18 ms,
1 time per direction, 2 times in total
Vibration Non-Operating IEC 60068-2-6, 10 Hz to 500 Hz @ 30 m/S² (3 G peak);
60 min per axis for all X, Y, Z direction
Bump Test Operating IEC 60068-2-29, Half Sine Wave: 10 G for a duration of 11 ms,
1,000 times per direction, 6,000 times in total
Over Voltage Category III According to IEC/EN 62477-1 / EN 60204-
1
(clearance and creepage distances) and
IEC 62103 (safety part)
Pollution Degree 2
Protections
Overvoltage < 57 V, SELV Output, Hiccup Mode,
Non-Latching (Auto-Recovery)
Overload / Overcurrent > 150% of rated load current, Hiccup Mode,
Non-Latching (Auto-Recovery)
Over Temperature < 80°C Surrounding Air Temperature @ 100% load,
Non-Latching (Auto-Recovery)
Short Circuit Hiccup Mode, Non-Latching
(Auto-Recovery when the fault is removed)
Internal Fuse at L pin T 3.15 A H
Degree of Protection IP20
Protection Against Shock Class I with PE* connection
*PE: Primary Earth

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
4
Reliability Data
MTBF > 800,000 hrs. as per Telcordia SR-332
I/P: 115 Vac, O/P: 100% load, Ta: 25°C
Expected Cap Life Time 10 years (115 Vac & 230 Vac, 50% load @ 40°C)
Safety Standards / Directives
Electrical Equipment of Machines
EN/BS EN 60204-1 (over voltage category III)
Electrical Equipment for Use in Electrical Power Installations IEC/EN/BS EN 62477-1 / IEC 62103
Safety Entry Low Voltage SELV (IEC 60950-1)
Electrical Safety SIQ Bauart EN 62368-1
UL/cUL recognized UL 60950-1 and CSA C22.2 No. 60950-1 (File No. E191395)
UL 62368-1 and CSA C22.2 No. 62368-1 (File No. E191395)
CB scheme IEC 60950-1, IEC 62368-1
UKCA BS EN 62368-1
Industrial Control Equipment UL/cUL listed UL 508 and CSA C22.2 No. 107.1-01 (File No. E315355)
CSA CSA C22.2 No. 107.1-01 (File No. 181564)
Hazardous Location / ATEX
(For DRP048V060W1BA)
cCSAus CSA C22.2 No. 213-M1987 and ANSI / ISA 12.12.01:2007
[Class I, Division 2, Group A, B, C, D T4, Ta= -25°C to +80°C
(> +50°C derating)]
ATEX EN 60079-0:2009, EN 60079-15:2010 [ II 3G Ex nA nC IIC
T4 Gc, Ta= -25°C to +80°C (> +50°C derating)]
Certificate No. EPS 12 ATEX 1 491 X
CE In conformance with EMC Directive 2014/30/EU and
Low Voltage Directive 2014/35/EU
For DRP048V060W1BA:
In conformance with Equipment for explosive atmospheres
(ATEX) directive 2014/34/EU
UKCA
In conformance with Electrical Equipment (Safety) Regulations
2016 No. 1011 and
The Electromagnetic Compatibility Regulations 2016 No. 1091
Galvanic Isolation Input to Output 4.0 KVac
Input to Ground 1.5 KVac
Output to Ground 1.5 KVac

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
5
EMC
Emissions (CE & RE) Generic Standards: CISPR 32, EN/BS EN 55032, CISPR 11,
EN/BS EN 55011, FCC Title 47: Class B
Component Power Supply for General Use EN/BS EN 61204-3
Immunity Generic Standards: EN/BS EN 55024, EN/BS EN 61000-6-1,
EN/BS EN 61000-6-2
Electrostatic Discharge IEC 61000-4-2 Level 4 Criteria A1)
Air Discharge: 15 kV
Contact Discharge: 8 kV
Radiated Field IEC 61000-4-3 Level 3 Criteria A1)
80 MHz-1 GHz, 10 V/M, 80% modulation (1 kHz)
Electrical Fast Transient / Burst IEC 61000-4-4 Level 3 Criteria A1)
2 kV
Surge IEC 61000-4-5 Level 3 Criteria A1)
Common Mode2): 2 kV
Differential Mode
3)
: 1 kV
Conducted IEC 61000-4-6 Level 3 Criteria A1)
150 kHz-80 MHz, 10Vrms
Power Frequency Magnetic Fields IEC 61000-4-8 Criteria A1)
10 A/Meter
Voltage Dips and Interruptions IEC 61000-4-11 100% dip; 1 cycle (20 ms); Self Recoverable
Low Energy Pulse Test (Ring Wave) IEC 61000-4-12 Level 3 Criteria A1)
Common Mode2): 2 kV
Differential Mode
3)
: 1 kV
Harmonic Current Emission IEC/EN/BS EN 61000-3-2, Class A
Voltage Fluctuation and Flicker IEC/EN/BS EN 61000-3-3
1) Criteria A: Normal performance within the specification limits
2) Asymmetrical: Common mode (Line to earth)
3) Symmetrical: Differential mode (Line to line)

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
6
Block Diagram

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
7
Device Description
1) Input terminal block connector
2) Output terminal block connector
3) DC Voltage adjustment potentiometer
4) DC OK control LED (Green)
5) Universal mounting rail system
Dimensions
L x W x D: 121 x 32 x 125 mm (4.76 x 1.26 x 4.92 inch)

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
8
Engineering Data
Output Load De-rating VS Surrounding Air Temperature
Output Load De-rating VS Input Voltage
Note
1. Power supply components may degrade, or
be damaged, when the power supply is
continuously used outside the shaded region,
refer to the graph shown in Fig. 1.
2. If the output capacity is not reduced when the
surrounding air temperature exceeds its
specification as defined on Page 3 under
“Environment”, the device may run into Over
Temperature Protection. When activated, the
output voltage will go into bouncing mode and
will recover when the surrounding air
temperature is lowered or the load is reduced
as far as necessary to keep the device in
working condition.
3. In order for the device to function in the
manner intended, it is also necessary to keep
a safety distance as recommended in the
safety instructions while the device is in
operation.
4. Depending on the surrounding air temperature
and output load delivered by the power
supply, the device can be very hot!
5. If the device has to be mounted in any other
orientation, please contact [e-mail]
for more details.
Fig. 1 De-rating for Vertical and Horizontal Mounting Orientation
> 50°C de-rate power by 2.5% / °C
No output power de-rating across the entire
input voltage range

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
9
Assembly & Installation
The power supply unit (PSU) can be mounted on 35 mm DIN rails in accordance with EN 60715. The device should be installed with
input terminal block at the bottom.
Each device is delivered ready to install.
Mounting
Dismounting
Fig. 2.1 Mounting
Snap on the DIN rail as shown in Fig. 2.1:
1. Tilt the unit upwards and insert it onto the DIN rail.
2. Push downwards until stopped.
3. Press against the bottom front side for locking.
4. Shake the unit slightly to ensure that it is secured.
Fig. 2.2 Dismounting
To uninstall, pull or slide down the latch with screw driver as
shown in Fig. 2.2. Then slide the power supply unit (PSU) in the
opposite direction, release the latch and pull out the power
supply unit (PSU) from the rail.
CAUTION: Must tighten wire to housing (Fig. 3.1) before
plugging into the terminal block connection (Fig. 3.2).
In accordance to EN 60950 / UL 60950 and EN 62368 / UL
62368, flexible cables require ferrules. Use appropriate copper
cables designed to sustain operating temperature of 60°C / 75°C
or more to fulfill UL requirements.
Connection
Fig. 3.1 Fig. 3.2

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
10
Safety Instructions
Vertical Mounting
•ALWAYS switch mains of input power OFF before connecting and disconnecting the input voltage to the unit. If mains are not turned
OFF, there is risk of explosion / severe damage.
•To guarantee sufficient convection cooling, please refer to the following instructions to ensure sufficient clearance around
the device.
Vertical Mounting: 50 mm (1.97 inch) above and below the device as well as a lateral distance of 20 mm (0.79 inch) to other
units.
Horizontal Mounting: 20 mm (0.79 inch) above and below the device as well as a lateral distance of 50 mm (1.97 inch) to
other units.
•Note that the enclosure of the device can become very hot depending on the surrounding air temperature and load of the power
supply. Risk of burns!
•Only plug in and unplug connectors when power is turned off!
•DO NOT insert any objects into the unit.
•Hazardous voltages may be present for up to 5 minutes after the input mains voltage is disconnected. Do not touch the unit during
this time.
•The power supplies are built in units and must be installed in a cabinet or room (condensation free environment and indoor location)
that is relatively free of conductive contaminants.
•CAUTION: “For use in a controlled environment”.
For DRP048V060W1BA:
•The power supplies unit must be installed in an IP54 enclosure or cabinet in the final installation. The enclosure or cabinet must
comply with EN 60079-0 or EN 60079-15.
•Warning: Explosion Hazard - Substitution of components may impair suitability for Class I, Division 2.
•Warning: Explosion Hazard - Do not disconnect equipment or adjust potentiometer unless the power has been switched off or the
area is known to be non-hazardous.
Horizontal Mounting