Delta Amplon RT Series User manual

www.deltapowersolutions.com
Delta UPS - Amplon Family
User Manual
The power behind competitiveness
RT Series, Single Phase
5/ 6/ 8/ 10 kVA
ESC
BATTERY PACK

II
Amplon RT Series
SAVE THIS MANUAL
This manual contains important instructions and warnings that you should
follow during the installation, operation, storage and maintenance of this
product. Failure to heed these instructions and warnings will void the warranty.
Copyright © 2022 by Delta Electronics Inc. All Rights Reserved. All rights of this
User Manual (“Manual”), including but not limited to the contents, information,
and figures are solely owned and reserved by Delta Electronics Inc. (“Delta”).
The Manual can only be applied to the operation or the use of this product. Any
disposition, duplication, dissemination, reproduction, modification, translation,
extraction, or usage of this Manual in whole or in part is prohibited without the prior
written permission of Delta. Given that Delta will continuously improve and develop
the product, changes may be made to the information in this Manual at any time
without obligation to notify any person of such revision or changes. Delta will make
all possible efforts to secure the accuracy and the integrity of this Manual. Delta
disclaims any kinds or forms of warranty, guarantee, or undertaking, either expressly
or implicitly, including but not limited to the completeness, faultlessness, accuracy,
QRQLQIULQJHPHQWPHUFKDQWDELOLW\RU¿WQHVVIRUDSDUWLFXODUSXUSRVHRIWKH0DQXDO

Table of Contents
III
Table of Contents
Chapter 1:Important Safety Instructions--------------------------- 1
1.1 Safety Instructions------------------------------------------------------1
1.2 Standard Compliance--------------------------------------------------4
1.3 Storage--------------------------------------------------------------------4
Chapter 2:Introduction --------------------------------------------------- 5
2.1 General Overview ------------------------------------------------------5
2.2 Exterior & Dimensions-------------------------------------------------5
2.3 Package List -------------------------------------------------------------6
Chapter 3:Operation Panel---------------------------------------------- 8
3.1 LED Indicators-----------------------------------------------------------8
3.2 Multi-function Buttons--------------------------------------------------9
3.3 LCD Display------------------------------------------------------------12
 ,FRQ'LVSOD\'H¿QLWLRQ---------------------------------------------------13
 2SHUDWLRQ0RGH'LDJUDP'H¿QLWLRQ ----------------------------------14
Chapter 4:Rear Panel ----------------------------------------------------16
Chapter 5:Communication Interfaces------------------------------21
5.1 RS-232 Port------------------------------------------------------------21
5.2 REPO Port--------------------------------------------------------------22
5.3 MINI Slot----------------------------------------------------------------22
5.4 USB Port----------------------------------------------------------------22
5.5 Dry Contacts-----------------------------------------------------------23
5.6 External Battery Connector ----------------------------------------25
Chapter 6:Installation----------------------------------------------------29
6.1 Rack Mounting --------------------------------------------------------29
6.2 Tower Mounting -------------------------------------------------------31
6.3 PDB Disassembly & Installation ----------------------------------33
6.3.1 Precautions Prior to PDB Disassembly -------------------------33

IV
Amplon RT Series
6.3.2 PDB Disassembly---------------------------------------------------------34
6.3.3 PDB Assembly -------------------------------------------------------------35
6.3.4 PDB Rack-installation----------------------------------------------------35
6.4 Battery/ Battery Pack Replacement------------------------------36
Chapter 7:Connection and Wiring-----------------------------------38
7.1 UPS Connection Warnings-----------------------------------------38
7.2 Input/ Output Connection-------------------------------------------39
Chapter 8:Operation -----------------------------------------------------42
8.1 Start-up------------------------------------------------------------------42
 7XUQRႇ ------------------------------------------------------------------44
8.3 Operation Mode-------------------------------------------------------45
Chapter 9:LCD Display & Settings ----------------------------------46
9.1 Initial Setting Screen-------------------------------------------------46
9.2 Main Menu--------------------------------------------------------------48
9.2.1 Measurement Menu ------------------------------------------------------51
9.2.2 Setting Menu ---------------------------------------------------------------51
9.2.3 Control Menu---------------------------------------------------------------57
9.2.4 Maintenance Menu--------------------------------------------------------58
Chapter 10:Optional Accessories -----------------------------------63
Chapter 11:Troubleshooting-------------------------------------------64
Chapter 12:Maintenance------------------------------------------------66
12.1 UPS ----------------------------------------------------------------------66
12.2 Batteries-----------------------------------------------------------------66
12.3 Fans----------------------------------------------------------------------67
$SSHQGL[7HFKQLFDO6SHFL¿FDWLRQV-------------------------------68
Appendix 2:Warranty ----------------------------------------------------71

Chapter 1 Important Safety Instructions
1
Chapter 1:Important Safety Instructions
1.1 Safety Instructions
Installation Warnings

zBefore installation and usage, please read this User Manual thoroughly. This
helps you to use the product correctly and safely.

zInstall the UPS in a well-ventilated area, away from excess moisture, heat, dust,
ÀDPPDEOHJDVRUH[SORVLYHV

z7RDYRLG¿UHDFFLGHQWVDQGHOHFWULFVKRFNSOHDVHLQVWDOOWKH836LQDWHPSHUDWH
and humidity well-controlled indoor area free of conductive contaminants. For
WKHWHPSHUDWXUHDQGKXPLGLW\VSHFL¿FDWLRQVSOHDVHUHIHUWRAppendix 1 : Tech-
QLFDO6SHFL¿FDWLRQV.

zLeave adequate space (at least 50cm) around all sides of the UPS for proper
ventilation.
Connection Warnings

zThe UPS must be well grounded due to a possible risk of current leakage.

zThe installation of upstream and downstream protective devices is highly recom-
mended when the UPS is connected to the mains and the loads.

zThe protective devices connecting to the UPS must be installed near the UPS
and must be easily accessible for operation.

z,I\RXQHHGWRPRYHWKH836RUSHUIRUPUHZLULQJSOHDVHWXUQRႇWKH$&LQSXW
power and ensure that the UPS has been safely shutdown. Otherwise, the out-
put end might still be energized, which might cause electric shock.
Usage Warnings

zThis is a class-A product. In a domestic environment, this product may cause ra-
dio interference, in which case, the user is required to take adequate measures.

zThe UPS can be used to power computers and associated peripheral devices,
such as monitors, modems, cartridge tape drives, external hard drives, etc.

2
Amplon RT Series

zIt is strictly forbidden to connect the UPS with:
1. Any regenerative loads.
2. Any asymmetrical loads.

zTo ensure reliable operation of the UPS and to protect the UPS from overheat-
ing, the slits and openings in the UPS must not be blocked or covered.

zBefore usage, you must allow the UPS to adjust to room temperature for at least
one hour to avoid moisture condensing inside the UPS.

zDo not pour and splash any liquid on the UPS. Do not insert any object into
the UPS’s slits and openings. Do not put beverage containers on or around the
UPS.

zWhen an emergency occurs, (1) press and hold the ON/ OFF button ( ) for
3 seconds, (2) release it after you hear one beep, (3) use the Scrolling UP or
Down button ( / ) to select 'Yes', and (4) press the Enter button ( ) to
FRQ¿UP\RXUVHOHFWLRQWRWXUQRႇWKH836$IWHUWKDWFXWRႇWKHLQSXWSRZHUWR
completely shut down the UPS.

zDo not use any cleaning liquid or cleaning spray to clean the UPS. Before clean-
ing, please make sure that the UPS has been completely shut down, the UPS’s
input power cord has been unplugged, and the batteries have been disconnect-
ed.

z$OOPDLQWHQDQFHVHUYLFHVPXVWEHSHUIRUPHGE\TXDOL¿HGVHUYLFHSHUVRQQHO

zForbid opening or removing the cover of the UPS yourself to avoid high voltage
electric shock.

z<RXPXVWFRQWDFWTXDOL¿HGVHUYLFHSHUVRQQHOLIHLWKHURIWKHIROORZLQJHYHQWVRF-
curs:
1. Liquid is poured or splashed on the UPS.
2. The UPS does not run normally after this User Manual is carefully
observed.
NOTE:
If you use the UPS in an area that generates or incurs dust, you should
LQVWDOODGXVW¿OWHURSWLRQDOLQWKHN9$836DQGWZRLQWKHN9$
UPS to ensure normal product life and function.

Chapter 1 Important Safety Instructions
3
Battery Warnings

zKeep the batteries away from heat sources. Do not open or mutilate the batter-
ies.

z'RQRWGLVSRVHRIEDWWHULHVLQD¿UH7KHEDWWHULHVPD\H[SORGH

zThe released electrolyte is harmful to the skin and eyes and may be toxic.

zA battery can present a risk of electric shock and high short-circuit current.

zServicing of batteries and battery packs must be performed or supervised by
qualified service personnel knowledgeable in batteries, battery packs and the
required precautions. Keep unauthorized personnel away from batteries and
battery packs.

zThe risk of electric shock and short-circuit current is possible when the batteries
are connected to the UPS. Before maintenance, disconnect all batteries to cut
RႇWKHEDWWHU\SRZHU

zFor battery replacement, only use the same number and type of batteries.

zObserve the following before replacing the batteries:
1. Remove watches, rings, or other metal objects.
2. Use tools with insulated handles.
3. Wear rubber gloves and boots.
4. Do not lay tools or metal parts on the top of batteries.
5. Disconnect charging source prior to connecting or disconnecting battery
terminals.
6. Remove battery grounds during installation and maintenance to reduce
likelihood of shock. Remove the connection from ground if any part of the
battery is determined to be grounded.

z'RQRWFRQQHFWWKHEDWWHULHVLQUHYHUVHRWKHUZLVHDULVNRIHOHFWULFVKRFNRU¿UH
accidents might occur.

zThe batteries might lose their power during shipment or storage. Before you use
WKH836IRUWKH¿UVWWLPHSOHDVHIXOO\FKDUJHWKHEDWWHULHVXQWLOWKHEDWWHU\FD-
pacity percentage shown on the UPS’s LCD is 100% ( 100%). If the UPS needs to
be stored for an extended period of time, please charge the batteries every three
months and ensure that, every time after charging, the battery capacity percent-
age shown on the UPS’s LCD is 100% ( 100%).

4
Amplon RT Series
WARNING:
1. The risk of electric shock and short-circuit current is possible when
the batteries are still connected to the UPS even though the UPS
is disconnected from the mains. Do not forget to cut off the battery
source before maintenance.
2. When the UPS is connected to external battery packs, the installation
of appropriate protective devices, such as a DC fuse or a DC non-fuse
breaker, is required.
1.2 Standard Compliance

zCE

zUL, cUL

zEN 62040-1

zEN 62040-2 Category C2
1.3 Storage

zPrior to installation
If the UPS needs to be stored prior to installation, it should be placed in a dry
and well-ventilated area. The allowable storage temperature is between -15°C
and +50°C (5°F~122°F).

zAfter usage
(1) Press and hold the ON/ OFF button ( ) for 3 seconds, (2) release it after
you hear one beep, (3) use the Scrolling UP or Down button ( / ) to
select 'Yes', and (4) press the Enter button ( WRFRQ¿UP \RXUVHOHFWLRQWR
WXUQRႇWKH8360DNHVXUHWKH836LVVKXWGRZQGLVFRQQHFWWKH836IURPWKH
utility AC power, remove all loads/ equipment from the UPS, and store the UPS
in a dry and well-ventilated area at a temperature between -15°C and +50°C
(5°F~122°F).
Idle batteries must be recharged fully approximately every three months if the
UPS needs to be stored for an extended period of time. Ensure that, every time
after charging, the battery capacity percentage shown on the UPS’s LCD is
100% ( 100%).
NOTE:
After storage and before start-up of the UPS, you must allow the UPS to
adjust to room temperature (20°C~25°C or 68°F~77°F) for at least one
hour to avoid moisture condensing inside the UPS.

Chapter 2 Introduction
5
Chapter 2:Introduction
2.1 General Overview
The RT series UPS is a single-phase input, single-phase output on-line uninterrupt-
ible power supply which provides reliable and consistent sine-wave quality power
to your electronic equipment. It adopts the latest technology and the highest quality
FRPSRQHQWVSURYLGLQJRXWSXWSRZHUIDFWRUXSWRXQLW\DQGLWVHႈFLHQF\LQRQOLQH
mode reaches up to 95.5%. The UPS not only provides safe, reliable and uninter-
ruptible power to your sensitive electronic equipment at all times, but also produces
greater electronic power efficiency at less cost. There are four different ratings,
N9$N9$N9$DQGN9$IRU\RXUVHOHFWLRQ
2.2 Exterior & Dimensions
The product that you receive is composed of three parts, a UPS, a battery pack and
a PDB (Power Distribution Box). Please refer to Figure 2-1 and Figure 2-2.
NOTE:
When handling or moving the product, please note that the force area of the
product is at the bottom of the battery pack, but not at the PDB.
ESC
BATTERYPACK
440mm
88mm
176mm
665mm
565mm
UPS
Battery Pack
PDB
)LJXUH6WDQGDUG5XQWLPH0RGHO.9$([WHULRU'LPHQVLRQV

6
Amplon RT Series
ESC
BATTERYPACK
130mm
218mm
750mm
565mm
440mm
UPS
Battery Pack
PDB
)LJXUH6WDQGDUG5XQWLPH0RGHO.9$([WHULRU'LPHQVLRQV
2.3 Package List
The package contains the following items. Please check if any item is missing. If
there is anything missing, please contact the dealer immediately.
Models: UPS502R2RT0B0B8/ UPS602R2RT0B0B8/ UPS802R2RT0B0B8/
UPS103R2RT0B0B8/ UPS502R2RT0B035/ UPS602R2RT0B035/
UPS802R2RT0B035/ UPS103R2RT0B035
× 4 or
× 6
× 4
www.deltapowersolutions.com
Delta UPS - Amplon Family
UserManual
Thepower behind competitiveness
RTSeries, Single Phase
5/6/ 8/ 10 kVA
ESC
BATTERYPACK
× 6
× 1 × 1
× 2
×
4
1 2 34
56
78 9
ESC
BATTERY PACK
ESC
BATTERY PACK
8/ 10kVA
5/ 6kVA
x 2
× 4
× 4
× 4
10
× 8× 8
× 4
For 5/ 6kVA For 8/ 10kVA
× 2
× 1 × 1
× 2
×
2
× 2
× 1 × 1

Chapter 2 Introduction
7
No. Item 5kVA
(0B8) 6kVA (0B8) 8/ 10kVA (0B8) 5/ 6kVA (035) 8/ 10kVA (035)
1UPS 1 PC 1 PC 1 PC 1 PC 1 PC
2User Manual 1 PC 1 PC 1 PC 1 PC 1 PC
3USB Cable 1 PC 1 PC 1 PC 1 PC 1 PC
4Rail Kit 1 SET 1 SET 1 SET N/A N/A
5Bracket Ear for PDB 1 SET 1 SET 1 SET 1 SET 1 SET
6Bracket Ear for UPS 1 SET 1 SET 1 SET 1 SET 1 SET
7Tower Stand 4 PCS 4 PCS 4 PCS 4 PCS 4 PCS
8Tower Stand Expander 4 PCS 4 PCS 6 PCS 4 PCS 6 PCS
9Pluggable Terminal 2 PCS 2 PCS 2 PCS 2 PCS 2 PCS
10
Cord End Terminal N/A 6 PCS 6 PCS 6 PCS 6 PCS
NOTE:
1. If there is any damage or anything missing, please immediately contact
the dealer from whom you purchased the unit.
2. If the UPS needs to be returned, carefully repack the UPS and all of the
accessories using the original packing material that came with the unit.
3. For rack-mount installation, if UPS maintenance is needed, you must use
the accessories ( 5%UDFNHW(DUIRU3'%) to install the PDB on a rack.
If there is no need to maintain the UPS, the installation of PDB's bracket
ears must be removed. For how to rack-mount the PDB, please refer to
3'%5DFNLQVWDOODWLRQ

8
Amplon RT Series
Chapter 3:Operation Panel
On the front panel of the UPS, you’ll see two LED indicators, a LCD display, and
multi-function buttons.
ESC
100 75%
%
ONLINE
Input 232.0V 50.0Hz
Output 232.0V 50.0Hz
1
3.1
LED Indicators
3.3
LCD Display
3.2
Multi-function
Buttons
)LJXUH2SHUDWLRQ3DQHO
3.1 LED Indicators
No. LED Description
11. ON: The output is protected.
2. OFF: The output is not protected.
2
1. ON: The UPS detects an internal fault or an
environmental fault.
2. OFF: The UPS is in normal state.
3. Flashing: The UPS shows the warning message(s).
Please check the corresponding warning
message(s) in &KDSWHU7URXEOHVKRRWLQJ.

9
Chapter 3 Operation Panel
3.2 Multi-function Buttons
No. Multi- function
Button Description
1 ON/ OFF
Button
The button has multiple functions. Please refer to the following
for detailed information.
1. Turn-on

zIn standby/ bypass mode, press and hold the button for 3
seconds, release it after you hear one beep and the UPS
will run in on-line mode.

zCold start: When there is no AC input, press and hold the
button for 3 seconds, release it after you hear one beep
and the UPS will run in battery mode.
7XUQRႇ

zIn on-line mode, (1) press and hold the button for 3
seconds, (2) release it after you hear one beep, (3) use
the Scrolling UP or Down button ( / ) to select 'Yes',
and (4) press the Enter button ( ) WRFRQ¿UP\RXUselec-
tion. After that, the inverter will be off and the UPS will
transfer to run in standby or bypass mode.
The UPS will keep charging the batteries when the UPS
LVLQVWDQGE\E\SDVVPRGH7RIXOO\WXUQRႇWKH836LWLV
advised to disconnect the UPS from the AC power.

zIn battery mode, (1) press and hold the button for 3
seconds, (2) release it after you hear one beep, (3) use
the Scrolling UP or Down button ( /) to select ‘Yes’,
and (4) press the Enter button ( WRFRQ¿UP\RXUVHOHF
WLRQ$IWHUWKDWWKH836ZLOOEHWXUQHGRႇ
3. Fault Clear

zWhen the UPS has a fault condition, press and hold the
button for 3 seconds, release it after you hear one beep
and the UPS will try to clear the fault condition.

10
Amplon RT Series
No. Multi- function
Button Description
NOTE:
1. When the UPS clears the fault condition, it
means that the buzzer/ warning message has
EHHQWXUQHGRႇ7RHOLPLQDWHWKHIDXOWGHWHFWHG
please refer to &KDSWHU7URXEOHVKRRWLQJ
for relevant solutions.
2. The function mentioned above is only appli-
cable to the condition when the UPS has a
IDXOWVLWXDWLRQDQGWKHLQYHUWHULVRႇ
2Enter
Button
The button has multiple functions. Please refer to the following
for detailed information.
1. Entering into the setup mode
In the Main Screen (that shows the current operation mode),
press the button for 0.1 second and the UPS will enter into
the Main Menu (setup mode). Please refer to &KDSWHU:
/&''LVSOD\6HWWLQJV.
6HOHFWLQJDQGFRQ¿UPLQJWKHSDUDPHWHULQVHWXSPRGH
In setup mode, press the button to choose the parameter
\RXZDQWWRFKDQJHDQGWKHSDUDPHWHUZLOOÀDVK3UHVVWKH
Scrolling Up or the Scrolling Down button to change the
SDUDPHWHUDQGSUHVVWKHEXWWRQDJDLQWRFRQ¿UPWKHFKDQJH
3Scrolling
Up Button
The button has multiple functions. Please refer to the following
for detailed information.
1. Scrolling Up/ Increasing Number

zIn the Main Screen, press the button for 0.1 second and
the UPS will directly enter into the Measurement Menu’s
level 3 (see )LJXUH0HQX7UHH), which contains
related Output information.

zIn setup up mode, the button is used to navigate the set-
ting items. Press the button for 0.1 second to go to the
previous setting item.

11
Chapter 3 Operation Panel
No. Multi- function
Button Description
3Scrolling
Up Button

zThe button is also used to navigate or set up the setting
parameter. Press the button for 0.1 second to go to the
previous display or to increase a number. If the button
is pressed for more than 2 seconds, the number will be
increased single digit every 0.2 second automatically until
the button is released or the number reaches its highest
value.
2. LCD Reset

zPress the Scrolling Up and the Scrolling Down buttons
together for 3 seconds to reset the LCD display.
4Scrolling
Down
Button
The button has multiple functions. Please refer to the following
for detailed information.
1. Scrolling Down/ Decreasing Number

zIn the Main Screen, press the button for 0.1 second and
the UPS will directly enter into the Measurement Menu’s
level 3 (see )LJXUH0HQX7UHH), which contains
related Output information.

zIn setup up mode, the button is used to navigate the set-
ting items. Press the button for 0.1 second to go to the
next setting item.

zThe button is also used to navigate or set up the setting
parameter. Press the button for 0.1 second to go to the
next display or to decrease a number. If the button is
pressed for more than 2 seconds, the number will be de-
creased single digit every 0.2 second automatically until
the button is released or the number reaches its lowest
value.
2. LCD Reset

zPress the Scrolling Up and the Scrolling Down buttons
together for 3 seconds to reset the LCD display.

12
Amplon RT Series
No. Multi- function
Button Description
5
ESC
Escape
Button
The button has multiple functions. Please refer to the following
for detailed information.

zBack to the Previous Menu Level
In setup mode, press the button for 0.1 second to go back to
the previous menu level.
NOTE:
If the LCD display goes dim, press any button mentioned above for 0.1
second to wake up the LCD display and enable each button function.
3.3 LCD Display
100 75%
%
ONLINE
Input
Output 232.0V 232.0V 50.0Hz 50.0Hz
1

13
Chapter 3 Operation Panel
 ,FRQ'LVSOD\'H¿QLWLRQ
No. Icon/ Display Description
1
1Indicates that the load bank status is ON.
1Indicates that the load bank status is OFF.
2
100%Indicates the battery capacity level.
X
Indicates that the battery is abnormal and needs
replacement. If the battery is abnormal, the bat-
tery capacity icon ( 100%)ZLOOEHRႇ
375% Indicates the load level (%).
4
Input 232.0V 50.0Hz
Output 232.0V 50.0Hz When the UPS runs normally, the display will
show the input/ output voltage and frequency.
Battery disconnected
0x1003
!
5 seconds
When the UPS has abnormalities or is in fault
condition, the display will show an error code
and its corresponding fault or warning message.
NOTE:
The error code and the fault/ warning
message will appear alternatively for
every 5 seconds.
5Indicates that the buzzer is muted.

14
Amplon RT Series
 2SHUDWLRQ0RGH'LDJUDP'H¿QLWLRQ
No. Diagram Description
1
100 75%
%
ONLINE
Input
Output 232.0V 232.0V 50.0Hz 50.0Hz
1
Indicates ONLINE mode.
2
100 75%
%
1
Input
Output 232.0V 232.0V 50.0Hz 50.0Hz
ECO
Indicates ECO mode.
NOTE:
In ECO mode, the diagram’s
SRZHUÀRZZLOOFKDQJHDFFRUGLQJ
to the UPS input voltage and
frequency. However, the ECO
icon ( ECO) shown on the
upper-left corner will not change
even if the UPS transfers to online
mode or battery mode.
3
100 75%
%
BATTERY 1
168
min
Runtime
Input
Output 0.0V 230.0V 0.0Hz 50.0Hz
Indicates BATTERY mode.
4
100 75%
%
BYPASS 1
Input
Output 232.0V 232.0V 50.0Hz 50.0Hz
Indicates BYPASS mode.

15
Chapter 3 Operation Panel
No. Diagram Description
5
STANDBY 1
100%
Input
Output 232.0V 0.0V 50.0Hz 0.0Hz
Indicates AC STANDBY mode.
6
100 75%
%
Freq. Conv. 1
Input
Output 232.0V 232.0V 50.0Hz 50.0Hz
Indicates Frequency Conversion
mode.NOTE:
In Frequency Conversion mode,
WKHGLDJUDP¶VSRZHUÀRZZLOO
change according to the UPS
input voltage and frequency.
However, the text Freq. Conv.
( Freq. Conv. ) shown on the
upper-left corner will not change
even if the UPS transfers to
battery mode.

16
Amplon RT Series
Chapter 4:Rear Panel

zModel: UPS502R2RT0B0B8
P2 P3 P4P1
MINI SLOT
DRY CONTACT RS-485 RS-232
REPO
OUTPUT BREAKER-2
250V AC 20A
OUTPUT SOCKET-2
20A MAX.
OUTPUT SOCKET-3
24A MAX. PER OUTLET
AC INPUT
MANUAL BYPASS SWITCH
WARNING:
OPENING THIS COVER PLATE WILL CAUSE
INVERTER SHUTDOWN.
ONLY AUTHORIZED SERVICE PERSONNEL
CAN OPEN AND OPERATE IT.
NORMA
L
EXTERNAL BATT. CONNECTOR 192V DC 29A
OUTPUT SOCKET-1
29A MAX.
TMOV
1 2 3 4 5 6
7
9
8
17
L6-30P
11 12
10
)LJXUHN9$5HDU3DQHO

zModel: UPS602R2RT0B0B8
MINI SLOT
DRY CONTACT RS-485 RS-232
REPO
OUTPUT BREAKER-1
250V AC 30A
MANUAL BYPASS SWITCH
OUTPUT BREAKER-3
250V AC 30A OUTPUT BREAKER-2
250V AC 20A
P2 P3 P4P1
WARNING:
OPENING THIS COVER PLATE WILL CAUSE
INVERTER SHUTDOWN.
ONLY AUTHORIZED SERVICE P ERSONNEL
CAN OPEN AND OPERATE IT.
NORMA
L
EXTERNAL BATT. CONNECTOR 192V DC 35A
UPS OUTPUT
AC INPUT
/1/2
/2
/1
UPS OUTPUT
AC INPUT
/1/2
/2
/1
OUTPUT SOCKET-3
29A MAX. OUTPUT SOCKET-2 20A MAX.
TMOV
OUTPUT SOCKET-1
30A MAX.
1 2 3 4 5 6 7
7
98
14
16
10 11 12 13
15
)LJXUHN9$5HDU3DQHO