DEMON ELECTRIC PHANTOM User manual

PHANTOM
Installation Manual
Scan to watch
assembly video

Table of contents
ASSEMBLY INSTRUCTIONS..........................................................................................3
KICKSTAND INSTALLATION..........................................................................................4
PEDAL INSTALLATION......................................................................................................5
HANDLEBAR INSTALLATION ......................................................................................6
CONNECT CONNECTORS .............................................................................................7
FRONT LIGHT AND FENDER INSTALLATION.....................................................7
INSTALL FRONT WHEEL.................................................................................................8
REMOVING/INSERTING BATTERY...........................................................................9
CHARGING E-BIKE.............................................................................................................10
SERIAL NUMBER LOCATION....................................................................................10
DISPLAY..................................................................................................................................11
SETTING INTERFACE..........................................................................................................12
DEFINITION OF BUTTONS................................................................................................12
OPERATION..............................................................................................................................12
POWER-ON PASSWORD..................................................................................................13
ASSIST MODE SELECT........................................................................................................14
SPEED AND MILEAGE.........................................................................................................14
DISPLAY SWITCHING..........................................................................................................14
WALK ASSIST MODE..........................................................................................................14
HEADLIGHT SWITCH...........................................................................................................15
POWER INDICATOR.............................................................................................................15
POWER DISPLAY...................................................................................................................16
USER SETTINGS...................................................................................................................16
EXIT ITEM.................................................................................................................................16
UNIT SETTING........................................................................................................................16
BACKLIGHT SETTING..........................................................................................................17
CLOCK SETTING....................................................................................................................18
POWER-ON PASSWORD SETTING.............................................................................18
AUTOMATIC SHUTDOWN TIME SETTING................................................................20
WHEEL DIAMETER AND SPEED LIMIT INFORMATION.......................................20
BATTERY INFORMATION...................................................................................................21
VIEW OF SYSTEM INFORMATION.................................................................................21
FACTORY SETTING..............................................................................................................22
DATA CLEARING....................................................................................................................22
FAULT INTERFACE DEFINITION.......................................................................................23
LITHIUM-ION BATTERY MAINTENANCE/STORAGE GUIDE.........................24
WARRANTYPOLICY...........................................................................................................26
WARNINGS AND SAFETY...............................................................................................29

BELOW ARE THE GUIDELINES FOR THE INITIAL
BATTERY CHARGING PROCESS:
• Before using the e-bike for the first time, we strongly recommend that you conduct a preliminary battery
check-up and perform a full charge for optimal performance.
• To charge the battery, before riding connect the e-bike to the charger and allow the battery to reach full
capacity. According to the manufacturer’s instructions, the initial charge typically takes between 48 to 72
hours prior to your first ride.
• During the charging process, keep an eye on the LED indicator or display on your battery charger. This will
give you insights into the charging progression. If you encounter any problems, don’t hesitate to reach out to
the manufacturer for assistance.
• After the battery has been fully charged, it’s recommended to take your e-bike out for a test ride. Pay at-
tention to its performance, including the speed, range, and power-assistance levels. Any significant discrep-
ancies might imply that the battery capacity is compromised and needs further attention.
• Even when the e-bike is not being used frequently, it’s crucial to regularly charge and discharge the bat-
tery. This practice helps to prevent battery degradation during periods of storage.
Email us at [email protected]

2 Phantom Manual |
IMPORTANT
Electric Bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage,
or failure of the bicycle or system and all other losses or damages to themselves and others and to any
property arising as a result of using the bicycle.
As with all mechanical components, the bicycle is subjected to wear and high stresses. Different materials
and components may react to wear or stress fatigue in different ways.
If the design life of a component has been exceeded, it may suddenly fail possibly causing injuries to the
rider. Any form of crack, scratches or change of coloring in highly stressed areas indicate that the life of the
component has been reached and it should be replaced.
Please do not hesitate to contact us. If any problems may occur, please email us at
customersuppor[email protected] for any customer service solutions such as replacement parts, technical
information, and any other issues.
All new E-Bike purchases come with a 2-year warranty, the warranty card must be filled in and
registered in order to qualify for warranty.
For any other commercial or general inquires please contact Demon Powersports at 905 881 9510 or
Email us at [email protected]
DO NOT DISASSEMBLE, MODIFY OR
REPLACE ELECTRICAL PARTS.
PLEASE NOTE: THIS MANUAL IS NOT INTENDED
AS A DETAILED USER, SERVICE, REPAIR OR
MAINTENANCE MANUAL. PLEASE SEEK
ASSISTANCE FROM A QUALIFIED TECHNICIAN FOR
SERVICE, REPAIRS OR MAINTENANCE.

3 Phantom Manual |
ASSEMBLY INSTRUCTIONS
Your bike has been pre-assembled and requires only a few simple steps to get it ready for you to ride:
Remove the outside carton after cutting the nylon bands. Remove all the inside cardboard protection and
bubble wrap. Carefully remove your bike from the carton and gently rest it in place. Be careful not to cut
any wires when cutting the zip ties.
Remove brake pad holders when installing, avoid squeezing the brakes when removing the pad holder.
Ensure the following pieces are included in the package. If there are any missing parts, please contact
Demon for help replacing missing pieces.
i) Bike
iv) Pedals
ii) Front Wheel & Axle
vii) Kickstand viii) Seat
iii) Front Fender
3 mm
10 mm
15 mm8 mm
13 mm
4 mm
5 mm
Wrench
Set
Screw
Driver
Allen Key
Set
vi) Assembly Tools
v) Charger

4 Phantom Manual |
INSTALL KICKSTAND
Install kickstand with the 5mm Allen key.
Ensure kickstand is behind the bracket on the left side of the bike during installation.
5 mm
Bracket on
left side of the
bike.
Turn bolts
counterclockwise.

5 Phantom Manual |
PEDAL INSTALLATION
Using the 15mm wrench provided in the toolkit, attach, and tighten the pedals. PLEASE NOTE – The pedals
are marked “L” for Left and “R” for Right.
L R
The left pedal is attached by turning it counter clockwise and the right pedal is tightened by turning it clock-
wise. Make sure the pedals are tightly attached to the crank arms to prevent stripping.
(See picture below)
15 mm

6 Phantom Manual |
HANDLEBAR INSTALLATION
Tighten the 4 pinch screws with 4mm Allen key. Loctite is recommend on the screw. Align the brake
controls so they are facing slightly downward. Make sure the handlebar is centered.
4 mm
CONNECT CONNECTORS
Connect the connectors near handle bar, make sure arrows are pointing towards each other when
connecting. Locate the battery key near handle bar and cut the key from zip tie.

7 Phantom Manual |
FRONT LIGHT & FENDER INSTALLATION
Install the headlight and fender to the front fork with the provided long bolt and nut, tighten with the provided
screwdriver and 10mm wrench.
Install fender support to the bracket on the fork using the 4 mm allen key.
4 mm

8 Phantom Manual |
FRONT WHEEL INSTALLATION
Install the front wheel on the front fork, make sure to align the brake disk with the brake caliper, Avoid
squeezing brakes and ensure the brake disc is not rubbing against the wheel.
Fasten the wheel hub using the quick release handle.
Ensure brake disk and
brake caliper are aligned.
Smaller side of spring
to be facing the wheel.
Open quick release
handle.
Closed quick release
handle.