Denon DBP-4010UDCI User manual

DENON
UNIVERSAL AUDIO /VIDEO PLAYER
DBP-4010UDCI
Owner's Manual
Manuel de l'Utilisateur
Manual del usuario
* Button illustrations used in this manual for operation explanation are for the
Remote Control Unit.
You can operate the unit using the button of the same name on the front panel
of the unit.
* les illustrations des boutons presentes dans ce manuel servent aexpliquer Ie
fonctionnement de la telecommande.
Vous pouvez controler I'appareil aI'aide du bouton portant Ie meme nom sur la
farrade de I'appareil.
* las ilustraciones de los botones utilizadas en este manual con propositos de
explicacion son para la unidad del mando adistancia.
Puede operar la unidad
utilizando el boton del mismo nombre en el panel
delantero de la unidad.
IGUII Graphical User Interlace
ijtfflM,
Use this manual in combination with the operating
guide displayed on the GUI screen.
IGUI Menu Operation (iGf'page 22)
hfhI¥W
Utilisez ce manuel en meme temps que Ie guide
d'utilisation affiche sur I'ecran GUI (Interface
graphique).
Fonctionnement du menu de I'interface graphique GUI
(&page22)
1Jl·f1n.!
Utilice este manual conjuntamente con la guia de
uso que aparece en la pantalla GUI.
IUso de los menus GUI (G"pagina 22)

ENGLISH FRANCAIS ESPANOL
---- ------------_._--------
ATTENTION:
• La ventilation ne doit pas etre genee en recouvrant les ouvertures
de
la ventilation avec des objets tels que journaux, rideaux, tissus,
etc.
•Aucune flamme nue, par exemple une bougie, ne dOit etre placee
sur I'apparel!.
•Veillez arespecter les lois en vlgueur lorsque vous jetez les piles
usagees.
•L:appareil ne doit pas etre expose aI'eau
ou aI'humidite.
•Ne
pas poser d'objet contenant du liquide, par exemple un vase,
sur I'apparei!.
PRECAUCION:
• La ventilaci6n no debe quedar obstruida par haberse cub,erto las
aperturas con objetos como peri6dicos, manteles, cortinas, etc.
•No debe colocarse sobre el aparato ninguna fuente inflamable sin
protecci6n, como velas encendidas.
• A la hora de deshacerse de las pi las, respete la normativa para el
cUldado del media ambiente.
•No exponer
el aparato al goteo 0salpicaduras cuando se utilice
•No colocar sobre
el aparato obJetos Ilenos de liquido, como !
Jarros.
CAUTION:
To completely disconnect this product from the mains, disconnect '
the plug from the wall socket outlet.
The mains plug is used to completely Interrupt the power supply to
the unit
and must be within easy access by the user.
PRECAUTION:
Pour deconnecter completement ce produ;t du courant secteur,
debranchez la prrse de la prise murale.
La prise secteur est utilisee pour couper completement
I'alimentation de I'apparell et I'utilisateur
dOlt pouvorr yacceder
facilement.
PRECAUCION:
Para desconectar completamente este producto de la alimentaclon
electrica, desconecte
el enchufe del enchufe de la pared.
EI enchufe de la alimentaci6n electrica se utiliza para interrumpir por
completo el suministro de alimentaci6n electrica a la unidad ydebe
de encontrarse en un lugar al que el usuallo tenga facil acceso
ICAUTION:
• The ventilation should not be Impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
•No naked flame sources, such as lighted candles, should be
placed on the unit.
•Observe
and follow local regulations regarding battery disposal
•
Do not expose the unit to dripping or splashing flUids
•
Do not place objects filled with liquids, such as vases, on the
unit.
IMPOTANT SAFETY
INSTRUCTIONS
1. Read these Instructions
2. Keep these instructions.
3. Heed all warnings.
4Follow
all instructions
5. Do not use this apparatus near water.
6Clean only
with dry cloth
7
Do not block any ventilation openings.
Install
in accordance With the manufacturer's Instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves.
or other apparatus (Including amplifiers) that produce heal.
9. Do not defeat the safety purpose of the polarrzed or grounding-type plug. A
polarrzed plug has
two blades With one wider than the other. Agrounding
type plug has
two blades and athird grounding prong_ The Wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet. consult
an electrrcian for replacement of the obsolete outlet
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles,
and the point where they eXit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12_ Use only with the cart, stand. tripod. bracket, or table til
specified by the .man .. Ufactu.re. r, or. SOld. With the apparatus. ~
When acart IS used, use caution when moving the cart/ • ~
apparatus combination to aVOid Injury from tip-over_ ,.1
13. Unplug this apparatus durrng lightning storms or when l ~
unused for long perrods of time. ~-
14. Refer all serviCing to qualified service personnel.
Servicing
IS requrred when the apparatus has been damaged in any way,
such as power-supply cord or plug IS damaged, liquid has been spilled or
objects have fallen Into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped
15 Batteries shall not be exposed to excessive heat such as sunshrne, fire or
the like.
Dealer Address
Dealer
Phon-e·-:N--o--.------+-----------------~
Mo(Je-1 N-o-.--·----------------------------------------
Serral No.
"CLASS 1
LASER
PRODUCT"
Date of Purchase
c:----c--:o---c----:--------.----------------------- --
Dealer Purchase from
CAUTION:
TO REDUCETHE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSETHISAPPLIANCETO RAIN OR MOISTURE.
A
The. lightning flash.With arroWh. ead s. ym. bol, .Wlthln an equilateral
trrangle,
IS Intended to alert the user to the presence of
unlnsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute arisk of electric
shock to persons.
AThe
excla. mation pornt .Wit. h.'n an. equilateral tri.angle IS Intended
to alert the user to the presence of important operating
and marntenance (servIcing) rnstructions
In the literature
accompanying the appliance.
The serial number of this product may
be found on the back of the unit. No
others have the same semi number as yours You should record the number and
other vital information here and retain this book as apermanent record of your
purchase to aid identification
in case of theft.
oSAFETY PRECAUTIONS
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT
BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
oLaser Class (IEC 60825-1:2001)
I

•••
oNOTE ON USE IOBSERVATIONS RELATIVES AL'UTILISATION I
NOTAS SOBRE EL USO
• Do not let foreign objects into the unit.
• Ne pas laisser des objets etrangers dans
I'appareil.
• No deje objetos extra nos dentro del
equipo.
• Keep the unit free from moisture, water,
and dust.
•Proteger I'appareil contre I'humidite, l'eau
et la poussiere.
• Mantenga el equipo libre de humedad. f-----------------1
agua y paiva.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
• Eviter des temperatures elevees
Tenir compte d'une dispersion de chaleur
suffisante lars de I'installation sur une
etagere.
•
Evite altas temperaturas.
Permite la suficiente dispersi6n del calor
cuando esta instalado en la cansola.
FCC INFORMATION (For US customers)
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
product
may not cause harmful interference, and (2) this product must accept any interference received, including
interference that
may cause undesired operation.
2.
IMPORTANT NOTICE: DO NOT MODIFYTHIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modification
not expressly approved by DENON may void your authority. granted hy the FCr. to use the product.
3. NOTE
This product has been tested and found to comply with the limits for aClass Bdigital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference
will not occur in aparticular installation. If this product does cause harmful interference to radio or
television reception, which
can be determined by turning the product OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient
or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the product into
an outlet on acircuit diHerent from that to which the receiver is connected.
•Consult the local retailer authorized to distribute this type
of product or an experienced radio/TV technician for
help.
This Class Bdigital apparatus complies with Canadian ICES-003.
Cet appareil numerique de
la classe Best conforme a la norme NMB·003 du Canada.
• Do not let insecticides, benzene, and
thinner come in contact with the unit.
•Ne pas mettre en contact des insecticides,
du benzene et un diluant avec I'appareil.
• No permita el contacto de insecticidas,
gasolina y diluyentes can el equipo.
•Never disassemble or modify the unit in
any way.
• Ne jamais de manter au modifier I'appareil
d'une maniere ou d'une autre.
• Nunca desarme 0modifique el equipo de
ninguna manera.
....--)\Itil
l
U~:~~~
~ 0: ~
• (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d'aeration.
•
No obstruya los orificios de ventilacion.
• Handle the pcwer cord carefully.
Hold the plug when unplugging the cord.
•Manipuler Ie cordon d'alimentation avec
precaution.
Tenir la prise lors du debranchement du
cordon.
•Maneje el cordon de energfa con cuidado.
Sostenga el enchufe cuando desconecte el
cord6n de energia.
f-----------------j. Unplug the power cord when not using the
unit for long periods of time.
•
Oebrancher Ie cordon d'alimentation
lorsque I'appareil n'est pas utilise pendant
de longues periodes .
•Oesconecte
el cordon de energia cuando
no utilice el equipo por mucho tiempo.
oCopyrights IOroits d'auteur IOerechos de Autor
•It is prohibited by law to reproduce, broadcast, rent or play discs in public without the consent of the
copyright holder.
•
La reproduction, la diffusion, la location, Ie priH ou la lecture publique de ces disques sont interdits sans
Ie consentement du detenteur des droits d'auteur.
•
De acuerdo con las leyes esta prohibido reproducir, emitir, alquilar 0interpretar discos en publico sin la
autorizaci6n del propietario de los derechos de autor.
IT

ENGLISH
Contents
Features'" ·2
GUI Menu Setup
· .. 41
.. ·41
········································41
··41
·42
HOMI Control Function .... .47
Operations Enabled During Playback
Pause Playback ..
Stop Playback (Resume Function) .
Skipping to the ChapterfTrack/File
You Want to Playback .
Looking for Specific Sections Using
the Search Modes .
Memorizing Locations
You Want to Replay
(Marker Function) .
.. .. ·43
Fast Forward/Fast Reverse .. 43
Step-by-Step Playback
.. 43
Slow Forward/Slow Reverse Playback .... 43
Playback
in Any Order (Random Playback) .. ·44
Playing Back Repeatedly (Repeat Playback) .. 44
Repeat Playback Between Specified Points
(A-B Repeat) .. 44
Playing Back
in Your Preferred Order (Program Playback) 45
Switching Audio
·45
Changing the Subtitles and Subtitle Style" 46
Switching the Angle 47
Changing the Brightness of the Display (Dimmer Control)" .. 47
.. .. ·32
... 32
.. ··32
.. 33
·21
········22
········22
·······23
......
·23
.... ···24
.......
25
···28
.. ·····28
.............................................
29
...... 29
· .. · .. ·30
...... 31
Menu Map .
GUI Menu Operation ..
Examples of GUI Menu Screen Displays .
Language
Setup" ..
HDMI Setup·........ .. .
Video Setup· · ..
Audio Setup ·
DENON LINK
Setup"
Pure Direct Setup
Ratings
Network Setup ..
Display Setup
Other Setup
Various Settings
Setting the Audio Mode ......
Changing
the Playback File Display
Making Other Settings ....·
Adjusting the Picture Quality (Picture Control)
.. 2
·3
·3
.. ····3
······3
······6
·7
.. · .. ·7
......... 7
·····7
·8
.... ·8
·8
··· .... ·9
.. 10
Connections
Getting Started
Accessories ..
Cautions on Handling .. · .. ·
Cautions
on Installation'"
About Media
Playable Media ..
Cautions on Using Media'
About the Remote Control Unit
Inserting the Batteries.......... . .
Operating Range
of the Remote Control Unit
Remote Control Settings (Remote Control Side)
..
Part Names and Functions" .
Front Panel"
..
Display'
Rear Panel ..
Remote Control Unit .
Specifications .55
Troubleshooting· ·53
Preparation....
.. 12
Cables Used for Connections' 12
1. Home Theater Playback -Playing Back Using Multi-channel
System _...... 13
Using an HDMI Cable to Connect to an AV Amp or Television· . 13
Required Settings for HDMI Connection ........ 13
Connection to an AV Amp with No HOMIAudio Input 15
Connecting to aDevice with
an Analog Multi-channel
Audio Input Terminal 16
DENON LINK Connection CD Making aJitter-free Connection' 17
DENON LINK Connection 0Making aNormal Connection ·17
Connection to an AV Amp with No HOMIVideo Input 17
2. Playing Back with a Direct Connection to aTV.... . 18
3. Playing Back 2-Channel Audio' 18
Connecting to aDevice with Analog 2-channel Audio Input
Terminal with Stereo
Pin Plug Cable 18
4. Recording aCD .. 19
Connecting to aDigital Recording Device 19
5. Using BD-L1VE function or updating the software version of
DBP-4010UDCI.. .. 19
Connecting to the Network .. · 19
Connecting the Power Cord' .. 20
Once
Connections are Completed.... .20
Turning the Power
On ·...... ·20
Playback
Introduction...... . .. 34
Before Playing aDisc
·34
Before Playing a SO Memory Card ·34
About Playback Information .. 34
Information Bar Display·......
.. 34
Media Player Display" .. 35
Playing
BD and DVD-Video.. .. .. ·36
Playing Back Super Audio CD . 37
CD Playback .. ·.. . 37
DVD-Audio Playback'" .. 37
Playing Back High-Quality Audio (Pure Direct Function) 38
File Playback ·38
File Playback'" . 39
About Screen Display During Playback ·40
Operation During Playback ..·40
Other Information
About DENON LINK·· · · · ..
About Advanced AL24 Processing'
About Copyright Protection Technology
Trademark Information
Language Code List .
Country Code List ..
Explanation of Terms'
Index'" ..
·.... ··48
········48
.... · .. ·48
.. ·48
.................... ···49
.... ····50
·....·51
...... 52
1

ENGLISH
Features
Universal Blu-ray Disc player that plays Super
Audio CD and DVD-Audio formats
GT'page 3, 4"Playable Media"
Jitter-free transmission owing to afusion of
DENON LINK 4th and HDMI transmission
technology
In addition to multi-channel digital balance transmission of Super
Audio
CD that was achieved in 3rd , DENON LINK 4th provides
the jitter control functionality during digital signal transmission.
&page 17 "DENON LINK Connection CD Making aJitter-free
Connection"
Equipped with Dolby TrueHD, DTS-HD Master
Audio decoder
Compatible with Linear PCM 192 kHz (one of the BD audio
formats)
and multi-channel output (6-ch).
&page 16 "Connecting to aDevice with an Analog Multi-
channel Audio Input Terminal"
"Advanced AL24 Processing" installed on all
channels to enhance HD audio performance
Detailed picture rendering with minimal distortion; accurate
sound localization
and rich bass.
Achieves playback more faithful to the original sound
on all
channels.
GUI installed with excellent operability and
visibility
&page 22 "GUI Menu Operation"
HDMI control ready
GT'page 47 "HDMI Control Function"
Newly developed "S. V. H. Mechanism" with low
center of gravity, vibration damping, quietness
and high accuracy
Employs 6-block construction to eliminate mutual
electrical and magnetic interference
Gettin Started
Thank you for purchasing this DENON product. To ensure proper
operation. please
read these owner's manual carefully before using
the product.
After reading them.
be sure to keep them for future reference.
Accessories
Check that the following parts are supplied with the product.
CD Owner's manual.. .. 1
oService station list . 1
®Power cord (Cord length: Approx. 5.9ft/1.8m) 1
@) Remote control (RC-1140)....................... .1
®R6/AA batteries.. . 2
® DENON LINK cable (Cord length Approx. 49ft/1.5 m) 1
(J) Audio cable (Cord length: Approx. 49ft/1.5m) 1
®Video cable (Cord length: Approx. 4.9ft/1.5m) 1
®Warranty (for North America model only) .. 1
®(j) ®
9'//
2
I

ENGLISH
ICautions
on Handling
oBefore turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
oPower is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
oImage persistence (image burn-in)
Do not leave the still images of the disc menu, DBP-4010UDCI
menu, etc., displayed on the TV screen for long periods. This can
result in image persistence (image burn-in) on the screen.
oAbout Condensation
If the DBP-401OUDCI unit is moved from acold place to awarm
place, or installed in aroom subject to rapid temperature rise from
aheater, etc" condensation (dew) may form on the internal parts of
the unit (operating parts and lenses).
If used in this condition, the DBP-401 OUDCI will notoperate correctly
and damage may result. If condensation is formed on the unit. leave
the DBP-4010UDCI unit for1 to 2hours with the power OFF before
use.
oCautions on using mobile phones
Using amobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
oMoving the unit
Be sure to remove adisc, turn off the power and unplug the power
cord from the power outlet. Next. disconnect the connection cables
to other system equipment before moving the unit.
o About Care
oWipe the cabinet and control panel clean with asoft cloth.
oFollow the instructions when using achemical cleaner.
oBenzene, paint thinner or other organic solvents as well as
insecticide may cause material changes and discoloration if brought
into contact with the unit. and should, therefore, not be used.
oSufficiently ventilate the place of installation
If the unit is left in aroom full of the smoke from cigarettes, etc"
for long periods of time, the surface of the optical pickup could get
dirty, in which case it will not be able to read the signals properly.
oNote that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
3
ICautions on Installation
Note:
For proper heat dispersal, do not install this unit in aconfined
space,
such as abookcase or similar enclosure,
*Note
=======~ 0 0000
Do not place the DBP-4010UDCI on an amp or other piece of
equipment that generates heat.
About Media
IPlayable Media
Discs
I ' ISymbols
:Playable Playable Used
Playable Media :formats/ I,in
this
,modes Iregion codes ,Owner's
IIManual
II
BD-Video
~
Include region
..
* 1,*2
-
B/u·'.7yD;s~
@l
DVD-Audio
~
Il1!liJJ
* 1 -
AUDIO
DVD-Video
%f
-Include region
Il1!ll1!J
* 1, *2
8CD
DVD-R,
~ DVD+R
EI!!I EI!!I
Video
mode,
Ii1!liJI
DVO.ReWrltllb,* DVD+R
-
DVD-RW,
~
AVCHD
DVD+RW
.w
format
L\VCHL>
Super Audio
~
mm
CD
~
--
5UP£K,tUDlOCD
CD
~Q~~
CD-R
I--
lID
CD-RW
*1BD-Video/DVD-Audio/DVD-Video discs may not operate as
described in this manual due to menu structure.
*2 : The BD player and BD-Video disc, and DVD player and DVD-
Video disc each have their region codes (code assigned for
each region). Playback is not possible if the codes do not
match.
ISee overleaf>

ENGLISH
~'-
I
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit rate:
48 kbps -192 kbps
•Audio type:
WMA Version 9
About Media
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit rate:
64 kbps -320 kbps
(144 kbps
non-compatible)
•Audio type:
MPEG 1Audio
La er 3
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit rate:
64 kbps -192 kbps
(Variable Bit Rate non
compatible)
•Audio type:
MC
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit length: 16 bit
•Number of channels: 2
ch
•Compatible versions:
Up
to DivX®6
• Maximum size: 2 GB
• M~ximum resolution:
4,096 x4,096 pixels
•
Minimum resolution:
32 x32 pixels
•Maximum file size:
12 MB
o
o
o
o
o
o
o
o
o
o
o
o
MP3
(.mp3)
WMA *
(.wma)
AAC *
(.m4a)
LPCM
(wav)
JPEG
(.jpg/jpegl
DivX®
(.avi/divx)
~
. microSD.card
Adapter
mlcroSD
Card
~
*1This unit supports SD Memory Card with FAT16 file system,
and SDHC Memory Card with FAT32 file system.
*2 : For miniSD Card and microSD Card adapter is necessary.
symbOI'1
Used Playable files
Playable cards in this (Symbols Used in
this
Owner's Owner's Manual)
Manual
-
---
SO Memory Card *1
~I WMA ICMUllPCM I
(8 MB - 2 GB)
SDHC Memory Card *1I
JPEG II DivX I
(4GB)
Data recorded for BD BONUS
miniSD
Card *2
mil
VIEW use
(8 MB - 2 GB)
.See "Files"
in
"Playable
microSD
Card *2Media"
(Gr'page 41 for more
information on files.
(8 MB - 2 GB)
~
miniSDcard
.Adapter
..... m;';5D C"d
-Ntii.
•This unit does not support mini SDHC and micro SDHC Memory
Card.
•Insert or remove a SD Memory Card while the power is in standby.
If you insert a SD Memory Card while the power is ON, the SD
Memory Card may not be read.
•The SD card used for the Bonus View function must have acapacity
of 1 GB or greater. Also the SD card must be initialized on the DBP-
401 OUDCI (G3T'page 31).
The following discs will not play back on this unit.
• BD-RE Ver1.0
(BD disc with cartridge)
•BD-ROM/BD-R/BD-RE discs containing recorded movie, still image,
audio, etc., files
•BD-R/BD-RE in which BDMV/BDAV is recorded
• HD DVD
•DVD-RAM
• CDV (Only the audio part can be played)
• CD-G (Only the audio signals can be output)
•Non-standard CD
(CD with copy protection, etc.)
•Unauthorised disc
(Pirated disc)
•Disc with recording area less than 55 mm in diameter
•Video Single Disc (VSDj /CVD/ Video CD /Super Video CD /
CompactDisc-lnteractive (CD-I) /Photo CDs
-N'U. ,;;S~D;.,,;,M,;,;,;;e~m,;,;,;;o~r ... y_C;;,;;a~r,;;d;,;;s;... _
•A disc may not be accessible or play back incorrectly due to audio
and video interruptions, etc., depending on the recording conditions
when recorded with a BD recorder or DVD recorder.
•Unfinalised DVD-R/-RW/+R/+RW, and CD-R/-RW discs may not play
back. Finalise discs before playing.
*This unit cannot play back files recorded under DRM (Digital
Rights Management) other than DivX® files.
•The abovementioned file type may also fail to play back depending
on conditions at the time of recording,
•If characters not supported on the menu screen are included in a
file name, title, artist name or album title, those are not displayed
correctly.
• JPEG format images stored in progressive format cannot be played
back. 4

ENGLISH
Track1 Track2 Track3 Track4 Track5
o CD
CDs are divided into several sections (tracks) These sections are
all allotted numbers, called the track numbers.
oFile
MP3IWMAlAAC/LPCM/JPEG/DivX@files recorded on DVD~R/-RWi
+R/+RW, CD~R/~RW and SD Memory Card are divided into large
segments (folders) and small segments (files). Files are stored in
folders, and folders can be placed for storage in ahierarchy. The
DBP-401OUDCI can recognize up to 8hierarchies of folder
DVO-R/-RW/+R/+RW, CO·R/-RW
or SO Memory Card
,. I 1stlevel
F F9rr1 ~ ~F F0'rr2 ~ ~
File 1 - - File2 Fi.le3 __ Folder3 2nd level
I I~ I 'I ~ 3rdlevel
- Fiile4 - - File5 - - F;lIe6 - - FlIe7 -
#
When writing MP3IWMA/AAC/JPEG/DivX® files on a CD~R/~RW disc,
set the writing software's format to "1509660" The files may not play
properly if they are recorded in other formats. For details, refer to the
instructions of your writing software.
Single layer Super Audio CD with
only an HD layer *.
Super Audio CD with adouble HD
layer *,offering extended playing
time and high sound quality.
Two-layer Super Audio CD with an
HD layer *and a CD layer.
The signals on the CD layer can
be played on aregular CD player,
•Hybrid disc
CD layer HD layer
*:All Super Audio CDs contain an HD (High Density) layer with high
density Super Audio CD signals. This layer can contain astereo
channel area, amulti-channel area, or both astereo channel and
multi-channel area.
oSuper Audio CD
[Type of Super Audio CD)
•Single layer disc
~
•Dual layer disc
oDVD-Audio
DVD-Audio discs are divided into several large sections (groups)
and small sections(tracks). These sectionsare all allotted numbers,
called the group numbers and track numbers.
DVD-Audio
Group1 -I- Group2
-Track1 -1- Track2 +Track3 ---1- Track1 -1- Track2
VIew D1vXlRl VOD Honto!
ThIs .. nul hes 3 vllltWS left.
00 you want to tiM
one of your 3 view& now?
Yes ~
.J;
•When you purchase or rent aDivX® file through the official site
of DivX® Video~On~Demand (VOD) services, a DBP~401OUDCI
registration code is required. For details, see "DivX® Registration"
(@"page 29). IIIwx~il!i!!'!
• A DivX® VOD file recorded with
adifferent code from the DBP-
4010UDCI registration code cannot
be played back.
•Some DivX® VOD files are restricted
with limited playable times. If your
DivX® VOD file has such alimit,
the number of playable times is
displayed on the DivX® VOD display
screen.
Use 88to select "Yes" if you want
to play back the file, or to select
"No" if you do not want to play it
back. The press 8to confirm the
selection.
About DivX® Video-an-Demand (VODI
About
Discs and Files
About Media
oBD-Video, DVD-Video
BD/DVD~Video discs are divided into several large sections (titles)
and small sections (chapter). These sections are all allotted
numbers, called the title numbers and chapter numbers.
[Example)
,
------- BD, DVD '/
-Title1 -I Title2
Chapter 1Chapter 2Chapter 1Chapter 2Chapter 3
rr-~I:;UI~I :
~~~~~
I
5

ENGLISH
About Copyright
.N'lia
Do not use record spray, antistatic agents, or benzene, thinner or
other solvents.
•If there
are fingerprints or dirt on discs, wipe them off before using
the disc.
•Use acommercially available disc cleaning set or asoft cloth to
clean discs. I
About Media
Do not wipe with acircular
motion.
Gently wipe the disc from the
inside towards the outside.
Cleaning Discs
•Unauthorised copying, broadcasting, public performance and
lending of discs are prohibited.
•This product incorporates copyright protection technology that
is
protected by U.S. patents and other intellectual property rights.
•Use of this copyright protection technology must
be authorized by
Macrovision, and
is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly
is prohibited.
•Portions of this product
are protected under copyright law and
provided under license by ARIS/SOLANA/4C
•Do not get fingerprints, oil or dirt
on discs.
•
Take special care not to scratch discs when removing them from
their cases.
•
Do not bend or heat discs.
•
Do not enlarge the hole at the center.
•
Do not write on the labeled (printed) surface with ball-point pens,
pencils, etc., or stick new labels
on discs.
•Water droplets may form
on discs if they are moved suddenly from
acold place (outdoors for example) to awarm place, but do not try
to dry them off using ahairdryer, etc.
•Do not eject
an SO Memory Card or turn off the DBP-4010UDCI's
power while the card content
is in playback. This may result in
malfunction or loss of the card's data.
•
Do not attempt to open or modify SO Memory Cards.
•
SO Memory Cards and files can be damaged by static electricity.
Do not touch the metal contacts of an SO Memory Card with your
fingers.
•
Do not use warped SO Memory Cards.
•After use,
be sure to remove any disc or SO Memory Card, and store
it
in its proper card case, to avoid dust. scratches and deformation.
•
Do not store discs in the following places:
1.Places exposed to direct sunlight for long periods of time
2.Dusty or humid places
3.Places exposed to heat from heating appliances, etc.
About Handling of Media
~
--- ~---- --- ---
~~- ===
• Do not push the disc tray in by hand when the power is turned off.
Doing
so could damage the set.
•
Set the disc with the labeled side facing up.
•Make sure the disc tray is fully open when inserting the disc.
•
Place the disc horizontally in the tray, aligned with the tray guide.
If adisc that cannot be played is loaded or the disc is loaded up-
sidedown, "NO DISC" is displayed on the player's display.
Inserting aDisc
•Insert an so Memory Card in the
direction
of the arrow into the SO
CARD slot with the label facing up.
•Insert the card straight into
SO CARD
slot until it clicks.
•
To remove the card, push it in the
direction of insertion, and then release
to eject.
'N,ua
•Only load one disc at atime. Loading two or more discs can damage
the unit or scratch the discs.
•
Do not use cracked or warped discs or discs that have been repaired
with adhesive, etc.
•
Do not use discs on which the sticky part of cellophane tape or
labels
is exposed or on which there are traces of where labels have
been removed. Such discs
can get caught inside the player and
damage it.
•
Do not use discs with special shapes, as they could damage the
player.
Inserting an SD Memory Card
ICautions on Using Media
6

ENGLISH
2 : Set the remote control code to "2".
Remote Control Settings (Remote
Control Side)
oIf the signal code of the remote control does not match the signal
code of the unit, the remote control code set on the unit is shown
on the display.
[Example]
If the code setting on the unit is "OENON 1", and the setting on the
remote control is "2", "PLAYER 1" is shown on the display.
Switches when the DBP-4010UDCI's remote control operates
another DENON
BD players in the vicinity,
Set the remote control code simultaneously on the main unit. too.
For how to set codes, see GUI menu: "Other Setup" -"Remote
Control Setting" -"Remote 10" (i3T'page 31).
[Remote control code setting]
:Set the remote control code to "1".
-N·na
oMatch the signal code of the remote control with the signal code of
the unit. If the remote control code is different. you cannot operate
the OBP-4D1 DUOCI with the remote control.
o Even if you change the remote control code, set GUI menu "Other
Setup" -"Remote Control setting" -"Receive Legacy Remocon"
(&page 31) to "Off" when operating the OBP-4D1 DUOCI with a
remote control other than OENON's.
Operating Range of the Remote Control
Unit
Point the remote control unit at the remote sensor when operating
it.
-Nei.a
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
About the Remote Control Unit
G) Put the rear cover back on.
CD Remove the remote control CV Set three R6/AA batteries in
unit's rear cover. the battery compartment in the
indicated direction.
-N·na
oUse R6/AA batteries in this remote control.
oReplace the batteries with new ones if the set does not operate
even when the remote control unit is operated close to the unit.
(The supplied batteries are only for verifying operation.)
oWhen inserting the batteries, be sure to do so in the proper direction,
following the "EEl" and "8" marks in the battery compartment.
o To prevent damage or leakage of battery fluid:
Do not use anew battery together with an old one.
Do not use two different types of batteries.
Do not attempt to charge dry batteries.
Do not short-circuit. disassemble, heat or dispose of batteries in
flames.
oIf the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
oRemove the batteries from the remote control unit if it will not be in
use for long periods.
oUsed batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
IInserting the Batteries
I
7

ENGLISH
Part Names and Functions I
Does not display when the HDMI cable is
not correctly connected and when the HDMI
connection is not verified.
41> Media indicators
BD:BD
DVD: DVD-Video, DVD-R/+R/-RW/+RW
DVD AUDIO: DVD-Audio
SUPER AUDIO CD :Super Audio CD
CD: CD
SO : SO Memory Card
Displays the inserted media.
oTime mode indicators
TOTAL: Total time of Super Audio CD and CD
SING: Elapsed time of title/chapter/track/file
being played back
REM: Remaining time of title/chapter/track/file
being played back
oGroup/Title/Track/Chapter indicators
oHDMI output indicator
Display when HDMI video or audio signals are
being output.
:SUPE~ij6iO; :BI~¥99J'_-Jf!:It~-_~)1QW_-_-~I_-_-£i_~~ :R;turn; fDDDiGrfAC+OTS--------Jl. I
~.S~_~-_-_-~_~ =.=.=.=.=. =.=.=.=.=. =.=.=.=.=. =.=.=.:,=. :,=.=.=.:, =.=.=.=.=. =.=.:,=.=. =,=.=.=.=. -.'.::~--~:.:: iD[]TMH~~~ i
:11 ~Cl A·B: ..... ..... ..... ..... ..... ..... ..... ..... HH HH i HDCD!ANGI.E':
t'ROG RAND: I::::: ::::: ::::: ::::: ::::: ::::: ::::_: _:_:::_:_---:.0 .:..0 _,,_,,_. _'_· .. ~·I:L P PCM MPEQ:1J."Km(;
m-l----- - J) .. __ m_.~ .. ------.-.
oPlayback mode indicators
~ :During Playback
II :During pause and step-by-step playback
PROG :During program playback
RAND: During random playback
C1 A-B :During repeat playback
• Information display
Displays various information or playback
elapsed time
and so on of the disc.
oPlayback format indicators
o Downmix indicator
Displayed when playing back downmix
permitted audio.
oAngle information indicator
Displayed when ascene on the currently playing
disc
has been shot at various angles.
o Audio channel indicators
Displays the number of audio signal channels
during playback.
2CH :2-channel playback
MULTI: Multi-channel playback
fI Revers·skip/Forward·skip buttons
I~,~I ···········(41)
4Il Stop button 1.1····· .. · .. ·· .. ····· .. ···· .. ·· .. ········ (41)
ell Play button I~I . (37)
~ Disc tray open/close button I~I (34)
~ Disc tray .. · · .. ······· .. ····· .. ···· (6)
4fI Display················ ..··.. ··········· .. ······ · .. ··· (8)
CD CLOCK CONTROL indicator .. ··············· (17.28)
Lights when playing BD with DENON LINK 4th
(jitter freetconnections.
~ DENON LINK indicator .. ········ .. · .. ·· .. ········ (48)
~ ADVANCED AL24 indicator (48)
When power is in standby mode. press 411 and 4t
to turn the power on.
(~
0
~~
(~
"~'''''''::.'!f:..~''f..':''~I'''''.
--,--
_I
-.
CLIIUoO>"''''''
I
'-0 ~
--2
.... _. _otlWf'''''''
II
~
r--€l
0,,><-
_~,~~[I]=v
=.= ee?'vr ~ l\VCHD Huml
HX
t. 0
C~
0
I_F_r_o_"_t_P_a_n_e_I 1 IL-D_is..;;,.p_la.....:y~ _
For buttons not explained here. see the page indicated in parentheses ( ).
oPower operation button
ION/STANDBy)··························· .. ·· .. ·· .. ······ (20)
•Power indicator (20)
oDISC LAYER button (37)
o PURE DIRECT button·· .. ················· · .. ···· .. (38)
oHOMIRESOLUTION button········ (13)
oRemote control sensor················ .. ·· ..··.. ······· (7)
o SO CARD slot (6)
o SOURCE button (34)
oPause/Still button III) (41. 43)
41!> Fast reverse/slow button I)··········· .. ···· (43)
G) Fast forward/slow button I~I .. ····· .. ··· .... (43)
8

ENGLISH
IPart Names and Functions
IRear Panel
For buttons not explained here, see the page indicated in parentheses ( ).
(~
(J)
(~
04'
4~
~
/l
~
DIGITAL OUT IPCWBITSTREAM)
~O~
~·~·······~n
]c!J[
Jlb:dl
G=J~ 0
.......................
WCJ\>D ~
lO····O
rO············~i
COAXIAL OPTICAL
DEN ON LINK
HDMIOUT
4th
ETHERNET
..........................
DD LJ ~~
FR Fl Rl
.
2ch AUDIO OUT
.
~
~Efo w
..... ·
to
C~····~····~··j
SW
C
SR Sl SBR SBl ·
·l
VIDEO OUT
.~ .... ~ ... ~ ... O. .. O .... oJ
··V······~~Mi····PI1lrf!··
S·VIDEO OUT
COMPONENT VIDEO OUT
REMOTE ((Q)"'@.=-
~
0000
7.1ch AUDIO OUT
CONTROL ·00····1ii
RS-232C STRAIGHT CABLE
I---
ROOM TO ROOM
'--
I[I
0 4~
4)
C·)
0
4·~
(19,20)
(13)
..... (17)
o7.1ch AUDIO OUT connectors (16)
f) VIDEO OUT connector' (18)
•S-VIDEO OUT connector (18)
oCOMPONENT VIDEO OUT connectors" .. (18)
(1) ROOM TO ROOM IN/OUT jacks
Extension jack for future use.
oRS·232C connector
Extension connector for future use.
eAC inlet lAC IN) (20)
9
oETHERNET connector"
oHDMI OUT connectors' ..
4D DENON LINK 4th connector
mDIGITAL OUT OPTICAL/COAXIAL
connectors (15)
~ 2ch AUDIO OUT connectors .. .(18)
For software recorded in multi-channel, analog
signals that have been down-mixed into 2
channels are output.
'~[.)j.
•Do not touch the inner pins of the connectors on the rear panel. Electrostatic discharge may cause
permanent damage to the unit.
•Do not put your finger or foreign object in the fan opening. Doing so could cause injury or unit failure.
•When outputting audio from a OTS-HO 7.1-channel source to HOMI or analog 7.1 channel audio, and to
2-channel analog audio, perform the following settings so that the audio is down mixed to the correct
2-channel analog audio output signal as intended by the producer of the source and OTS, Inc.
'In "HOMI Setup", set "Audio Setup" to "2ch" (&page 23).
'In "Audio Setup", set "7.1 ch Audio Out" to "2 Channel" (&page 25).
If "Audio Setup" in "HOMI Setup" and "7.1 ch Audio Out" in "Audio Setup" are not set to "2ch" or "2
Channel" respectively, 2-channel analog audio is output using this unit's own downmix.
In this case, the downmix may differ from that intended by the producer of the source and OTS, Inc.

ENGLISH
IRemote Control Unit
For buttons not explained here, see the page indicated in parentheses ( ).
oRemote control signal transmitter .. ···················· .. ·· .. ·············· .. (7)
f) POWER buttons (POWER OFF, POWER ONI (20)
o HDMI RESOLUTION button (HDMI RES.I········· .. ·· .. ··.. ·····(13)
oHDMI MODE button ·········(14)
Cit Number buttons (0 -9, +101" ..·······(35.36)
oMODE button··········· ·······(32)
8DIMMER button······ '(47)
oTOP MENU button (TI (36)
oENTER button ·· · .. · .. ····(22)
4Dl SETUP button (SI" (21)
G) Fast-reversing button (~I '(43)
4f) Pause/Still button (III (41, 43)
4Il Revers-skip button (~I (41)
~ ANGLE button" .. (47)
Gil DISPLAY button....·(34)
CD RED/GRN/BLU/YEL buttons
iI PURE DIRECT button ·(38)
4Jj) PICTURE ADJUST button · ··........ (33)
~ SOURCE button" '''(34)
WDisc tray OPEN/CLOSE button (~I '(34)
~ PROGRAM/DIRECT button (PROG/DIRECTI '(45)
oRANDOM button.... .. '(44)
~ CLEAR button' .. (33)
~ SEARCH button (SRCHI'" ··(37)
~ CALL button" · · · .. · · · ·(45)
DENON
RC-1140
Part Names and Functions
~ REPEAT button ·· · ··(44)
~ A-B button···· .. ·· · .. ·· .. · · ..·· .. · ..·· · .. · .. · ··.. · ·· .. ·(44)
~ MENU/POP UP MENU button (36)
@l Cursor buttons (~'\l <ll>1 · · · .. · · ··(22)
G> RETURN button (R) · ·· · .. · · · .. · · ··(22)
G) Play button (~I (37)
~ Fast-forwarding button (~I"'"'''''''''''' ·(43)
Gl Stop button (_) .. (41)
Gl Forward-skip button (~I ·(41)
~ SUBTITLE button' "(46)
~ AUDIO button .. .. ·(45, 46)
@i) PAGE +button ··(38)
~ DISC LAYER button·· · .. · .. ·.. · .. · ·· .. ··(37)
•When power is in standby, press ~ and G) to turn the power on.
• You can use C9 when operating the SO popup menu screen, etc.
10
I

ENGLISH
Connections
DBP-4010UDCI
,- ~o 0000
o .. ·~· ...
•2ch stereo pin plug cable (unbalanced) connection
"Connecting to aDevice
with Analog 2-channel Audio
Input Terminal with Stereo
Pin Plug Cable" (@,page 18)
•LAN connection
"Connecting to the Network" (~page 19)
3Playing Back 2-Channel
Audio &page 18
DBP-401OUDCI
5Using BD-L1VE
function
or updating the software &page 19
version
of DBP-4010UDCI
(W'page 19
c::::=:Jo 0000
~o:~:~ I [==:J I ~o~~
.. ~o 0000
o ••• ~.···
DBP-4010UDCI
.. ~o 0000
o ••• ~.,··
•••••••••••••••••••••••• or ••••••••••••••••••••••••
•HDMI connection (~page 13)
• Analog video connection (@'page 18)
('-- A_u_d_io_+_V_i_de_o ~)
2Playing Back
with a Direct
Connection to a TV (W'page 18
• Digital output
"Connecting to aDigital Recording Device" (@'page
15)
4Recording aCD
DBP-4010UDCI
~o 0000
O"·~·'··
DBP-4010UDCI
OIc=::JIO
~.: I I... 1------11
~~~
Multi-channel Audio
•DENON LINK connection
"Making aJitter-free Connection"
(@,page 17)
"Making aNormal Connection" (@,page 17)
• Digital audio connection
"Connection
to an AV Amp with No HDMI Audio Input" (@,page 15)
• Analog 7.1 ch connection
"Connecting
to aDevice with an Analog Multi-channel Audio Input
Terminal"
(@'page 16)
• Analog video connection
"Connection to
an AV Amp with No HDMI Video Input" (~page 17)
••••••••••••••••••••••••••••••• or •••••••••••••••••••••••••••••••
( Multi-channel Audio + Video)
•HDMI connection
"Using an HDMI Cable to Connect to an AV Amp or Television" (@'page
13)
1 Home Theater Playback (W' page 13
-Playing Back Using Multi-Channel System -
Connect the DBP-4010UDCI as follows before using. Make connections according to the equipment you are connecting.
Some DBP-4010UDCI
settings may be necessary depending on the connection method. Check each connection item for more information.
I
•Connecting the Power Cord (W' page 20
•Once Connections are Completed
11

ENGLISH
Preparation
Prepare the cables to match the devices you are to use.
ICables Used for Connections I
t?'
• Use only HOMI (High Definition Multimedia Interface) cable that
bears the HOMI logo (genuine HOMI product). Using cable without
the HOMIIogo (non-genuine HOMI product) may result
in abnormal
playback.
•When outputting deep colour or
10S0p, etc., we recommend you
use High Speed HDMI cable for enhanced high-quality playback.
.N-U-
• Do not plug the powercord intothe power outlet until all connections
are completed.
•
Be sure to read the owner's manuals for the connected devices.
•First check the connection channels,
and then correctly connect the
input
and output channels.
•
Do not bundle the power cord together with the connection cables.
This
can result in noise.
Video cables
Other cables
Component video 03EO''I
connections 0o(PB/CB)
(Sold separately) 0o(PR/CR)
Component video (75 O/ohms) cable
S·Video @0
c:()
@
connections 0 0
(Sold separately) S-Video cable
Video connections G
cj[J::
~
0
(Included)
75 O/ohms pin-plug video cable
OENON LINK
(]
~
~
(]
connections
(Included) OENON LINK cable
Network
connections
(]
~ ~
(]
(Sold separately) Ethernet cable
Pin-plug cable
Optical cable
~ {)~-----~ClP ~
o~
o ~
Stereo pin plug cable
l§J 0 0 l§J
19-pin HOMI cable
Audio and video cables
HOMI connections
(Sold separately)
Coaxial digital 0 ~ 0
connections
(Sold separately) Coaxial digital (75 O/ohms pin-plug) cable
Optical digital
connections
(Sold separately)
Analog connections
(stereo, surround)
(1 included)
Analog connections 0 cj[J:::-------::D!P CO
(center, subwoofer)
(Sold separately)
12

ENGLISH
1. Home Theater Playback -Playing Back Using Multi-channel System -
HOMI
IN
nop
(720 progressivei
1080i
(1080 interlaced)
Source Direct -- 480/576i -- 480/576P
(Source direct) (480/576 interlaced) (480/576 prOgreSSiV~
1080P
(1080 progressive)
•If the HDMI resolution is not set to "Auto", set it to correspond with the resolution of your television.
Images will not be projected normally if the television resolution and DBP-401 OUDCl's output resolution
do not match.
•Audio and video will be temporarily interrupted if the power of the connected device currently playing
back is turned off, or input is switched.
•When you change the HDMI video resolution of the DBP-401 OUDCI, it takes from a few seconds up to
about 10 seconds for validation between the DBP-4010UDCI and the connected device. Audio/video is
not output during this period.
•When outputting deep colour or 1080p, etc., we recommend you use High Speed HDMI cable for
enhanced high-quality playback.
oConnection to adevice with aOVI-O terminal
If you use aHDMIIDVI-D conversion cable (sold separately), HDMI video signals are converted to DVI-
Dsignals, enabling connection to adevice with a DVI-D terminal.
'N,n-
• In this case, the audio signal is not output. Make the appropriate audio connections for your devices.
(Grpage 14 - 20).
•The video signal will be in RGB format.
• You cannot output to a DVI-D device that does not support HDCP (high-bandwidth digital content
copyright protection system).
•Video may not be output depending on the combination of devices.
Setting HOMI video output
oMake HOMI Output Signal and HOMI Control Function Settings
"HDMI Setup" (Grpage 23,24)
oMake the Video Output Signal Setting for the Connected Television
"Video Setup" ((W'page 24)
oAbout HOMI Video Resolution Setting
RESOLUTION
•Change the HDMI video resolution by pressing I ~~~' ]. Switch the output mode as follows. Default
settings are underlined.
[
Auto
(Auto)
1080P24
(1080 progressive, 24-frame)
IRequired Settings for HOMI Connection
•When connecting with an HOMI cable, press ll\;l and set it to "HOM IOn".
•OBp·4010UOCI automatically detects audio/video signal supported by the connected HOMI
device and outputs the signal. To change the setting, see "HOMI Setup" on the GUI menu
IGT'page 23, 24).
•When you press l~) and set it to "HDMI On", no video signals are output from the component
video outputs.
• To disable video or audio output from the HDMI terminal, set "Video Out" of "Pure Direct Setup",
which outputs high quality analog audio to "Off". To enable the HDMI signal output. set the Pure
Direct mode to one of the following setting:
• Pure Direct mode"Off" or "User Preset 1" or "User Preset 2"' ('*)
("Playing Back High-Quality Audio (Pure Direct Function) " Grpage 38)
'* Do this after setting "Pure Direct Setup" -"User Preset 1" or "User Preset 2" -"Video Out" on GUI
menu to "On" (Grpage 28)
During "HOMI On"
Audio/video signals are output from the HDMI terminal.
When the HDMI video resolution is set to "Auto" as described in "About HDMI Video Resolution
Setting" (Gr page 13), the DBP-401 OUDCI outputs the highest resolution video signal that is supported
by the connected equipment.
AVAmp or
TV
Using an HOMI Cable to Connect to an AV Amp or Television
I
i 'N'O-
I
I
I
I'N,n-
"
•When audio/video signals are output from the HDMI terminal, no video signals are output from the
component terminals.
•When asignal comprising 24 frames persecond, such as 1080P24, is output from the HDMI terminal,
no video signals are output from the video or S-Video outputs.
IDurin "HOMI Off"
lAudiolvideo is not output from the HDMI terminal.
I
When outputting avideo signal comprising 24 frames per second from the HDMI terminal, select
"1080P24" or "Source Direct" after setting the GUI menu "HDMI Setup" -"I/P Direct" (Grpage 23) to
"On". ISee
overleaf>
13

ENGLISH
1. Home Theater Playback -Playing Back Using Multi-channel System -
Even if "HDMI Setup" -"Audio Setup" on the GUI menu is set to "Auto" (~page 23), multilinear PCM
or downmixed 2-channel linear PCM signals are output if adevice that does not support bitstreams is
connected.
* 1 :Multi
LPCM signals are output when "BD Audio Mode" is set to "Mix Audio Output " (~page 32).
Multi LPCM signals are output when outputting HDMI video signals with resolutions of 480i/576i or
48Dp/576p.
* 2 :Super Audio
CD audio signals are output at 44.1 kHz 16-bit.
oAudio signal from the HOMI output terminal
You can change the audio format and playback number of channels according to the specifications of
the device to which the DBP-4010UDCI's HDMI audio output signals are input. Make settings while
checking the specifications of the audio device to
be connected as well as the audio format/number
of channels stored
in media and files for playback. I
2 ch Downmix
LPCM
2 ch Downmix
LPCM
2
ch Downmix
LPCM
2
ch Downmix
LPCM
2 ch Downmix
LPCM
Multi LPCM
Multi LPCM
---fsening "HDMt-Setup" - .. Audio-Setup" {~page-l3t-on
I 'h.G __
--
Audio formatMedia/Files
: I
Auto
Dolby Digital Dolby Digital * 1
Dolby Digital Plus Dolby Digital Plus * 1
Dolby TrueHD Dolby
TrueHD * 1
DTS
DTS* 1
DTS-HD
DTS-HD* 1
LPCM
Multi LPCM
AVCHD Dolby Digital Dolby Digital
LPCM Multi LPCM
Dolby Digital Dolby Digital
DVD-Video
DTS
DTS
LPCM 2 ch LPCM
DVD-Audio LPCM,
PPCM
Multi LPCM
Multi area
Super audio CD *2Stereo
area
2 ch LPCM
CD layer
DivX® Dolby Digital Dolby Digital
MP3,
MP2
2 ch LPCM
CD, MP3, WMA, AAC, LPCM
DTS-CD
DTS
•When you press C5 and set "HDMI Setup" ~ "Audio Setup" to "Auto" (~page 23) on the GUI menu,
audio mode
is set according to the connected device.
•When
you want to set the HDMI audio output separately, change according to the following table.
•Refer to the owner's manual of the connected device regarding HDMI audio input specifications
compatible with the connected device.
Setting HOMI Audio Output
'~'D
•When the HDMI video resolution is set to "1080P24", HDMI video signals are output from the DBP-
401 OUDCI with aresolution of 1080P and aframe rate of 24 frames per second, regardless of the video
signals
on the disc being played. Because of this, when playing discs containing video signals recorded
with aframe rate of something other than
24 frames per second, the movement of the picture may be
unnatural. If this happens, set the HDMI video resolution to something other than "1080P24".
•When the "liP Direct"
(11::11 page 23) setting is "On" and adisc with aframe rate of 24 rrames per second
is played, no video signals are output from the video or S-Video outputs.
•When the "liP Direct"
(~page 23) setting is "Off", "1080P24" is not displayed.
Device to be connected ISetting items IAbout output signal and speaker settings
Device with the following
DBP-401 DUDCI outputs abitstream signal that is decoded
built-in decoder
by the connected device.
·Dolby
TrueHD
'* In this case, you cannot make aspeaker setting for HDMI
·Dolby Digital Plus Auto audio with the
DBP-401OUDCI.
·Dolby Digital Make the setting with the connected device.
·
DTS-HD
'* When (~utting the Dolby TrueHD or DTS-HD audio,
·
DTS
press MOllE and set "BD Audio Mode" to "HD Audio
Output'
(~page 32).
Outputs multi-channel Linear PCM audio signals with
Device compatible with speaker setting by the DBP-4Dl
DUDCI.
multi-channel HDMI audio Multi LPCM
'* For speaker setting, on the GUI menu, "Audio Setup"
input, but not capable of
BMOn
-"7.1ch Audio
Out"- "Multi Channel" -"Speaker
speaker setting for each Configuration"
(~page 25).
channel
'* BM :Bass Management (means multi-channel speaker
setting)
Device compatible with Output of multi-channel Linear
PCM audio signals from the
multi-channel HDMI audio Multi LPCM
DBP-4D1DUDCI.
input.
and capable of BM Off Perform the speaker setting with the connected device.
speaker setting for each
'* BM : Bass Management (means multi-channel speaker
channel setting)
Device compatible with
2-
Downmixed 2-channel Linear PCM audio signals are output
channel HDMI audio input
2ch
from the DBP-4D1 DUDCI.
Perform the speaker setting with the connected device.
Audio signal are not output from the
DBP-4D1 DUDCI's
Device not compatible with Mute HDMI terminal.
HDMI audio signal input Only video signals
are output from the HDMI terminal.
'* Make the audio connection.
14

ENGLISH
1. Home Theater Playback -Playing Back Using Multi-channel System -
•When playing back Dolby Digital Plus/Dolby TrueHD/DTS-HD audio recorded on a BD disc. the DBP-
. 401 OUDCI outputs Dolby Digital or DTS bitstream from its digital audio output terminal.
IConnection to an AV Amp with No HOMI Audio Input
Ah' shapes
AVAmp
-AUDIO-
COAXIAL
IN
OPTICAL
iIN
i ~ o[~)f----e:JP
I-~[.n.
I0Dolby TrueHD/Dolby Digital Plus/DTS-HD audio signals are not output with
this connection.
When outputting Dolby TrueHD/Dolby Digital Plus/DTS-HD audio signals. do
so with an HDMI connection (l2U'page 13. "Using an HDMI Cable to Connect
to an AV Amp or Television").
oSuper Audio CD's DSD signal cannot be output. Also. during CD layer
playback. 44.1 kHz/16-bit Linear PCM is output.
o Do not output DTS audio signals to an AV Amp that does not support DTS. Playing back aBD/DVD
disc with recorded DTS content can generate noise and even damage your speakers.
oWhen connecting with an optical transmission cable (sold separately), make sure the plug shape
aligns with the socket. and insert fully.
In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection.
both the player and TV or the AV Amp need to support the copyright protection system known as
HDCP (High-bandwidth Digital Content Protection System). HDCP is copyright protection technology
comprised of data encryption and authentication of the connected AV device. The DBP-4010UDCI
supports HDCP
Copyright protection system
-N'U.
oIf adevice that does not support HDCP is connected. video and audio are not output correctly. Read the
owner's manual of your television or AV Amp for more information.
oThe audio signal from the HDMI output terminal (sampling frequency. number of channels. etc.) may
be limited by the HDMI audio specifications of the connected device regarding permissible inputs. For
example. if the HDMI audio specification of the connected device is 5.1 channels. 5.1-channel audio
will be automatically output even when playing back 7.1 channels by the DBP-401 OUDCI. In this case.
analog audio output will also be 5.1-channel.
oAudio signal input may not be supported depending on the HDMI compatible monitor (projector. etc.)
being used.
When the DBP-4010UDCI is connected to this kind of device. audio signals are not output from the
HDMI terminal.
I
15

ENGLISH
1. Home Theater Playback -Playing Back Using Multi-channel System -
Audio Signal from the Digital Audio Output (Optical/Coaxial) Terminal
c
"
I
#
In the case of a5.1-channel 1
connection, you need not
connect the
SBR/SBL terminals. I
In this case, on the GUI menu, i
select "Audio Setup" - "7.1 ch J
Audio Out" -"Multi Channel" - .
"Speaker Configuration" -
"Surr.
Back", and set "Size" to "None"
(&page 25).
Connecting to aDevice with an Analog Multi-channel Audio
Input Terminal
Outputs multi-channel audio decoded by the DBP-4010UDCI
I If your audio system has an analog multi-channel audio input terminal, connect using audio cable (sold
Iseparately).
2
ch Downmix LPCM
2ch Downmix LPCM
(DTS*2)
2ch LPCM
Dolby Digital
DTS
Bitstream PCM/PCM Down Sampling
AVAmp
-AUDro-
Dolby Digital
FRONT
Dolby Digital Plus
Dolby Digital * 1
L~
Dolby TrueHD
Re
SUBWOOFER
DTS
e
DTS*l
DTS-HD
CENTER
LPCM 2
ch Downmix LPCM * 1 e
2ch Downmix LPCM
Dolby Digital Dolby Digital
SURROUND
LPCM 2ch Downmix LPCM
Le
Dolby Digital Dolby Digital
Re
DTS DTS
e
LPCM 2
ch Downmix LPCM
Re
LPCM, PPCM
Multi area
DVD-Video
BD
AVCHD
* 1 :Bitstream signals are output in accordance with the BD re-encode setting when "BD Audio Mode"
is set to "Mix Audio Output" ((jT'page 32).
* 2 :When "HDMI Setup" -"Audio Setup" is set to 'Auto" on the GUI menu and bit stream is output from
HDMI ,the
DTS bit stream is output from the digital audio output (optical/coaxial) as well.
The DBP-401 OUDCI can convert and output digital audio signal format recorded on media.
Convert the digital audio signal
in accordance with the specifications of the device that is to input digital
audio output signals from the DBP-4010UDCI.
For content with copyright protection, audio signal is down sampled to 48kHz 16bit and is output.
16

ENGLISH
1. Home Theater Playback -Playing Back Using Multi-channel System -
o
DENON LINK Connection @Making aNormal Connection
AVAmp
-AUDIO-
DENON LINK
•When connecting to aDENON L1NK·compatible AV Amp, the multi-channel signals of DVD-Audio
discs, Super Audio CDs, etc., can be transferred as such in digital format.
•DENON LINK connection requires that the version of AV Amp to be connected match the DBP-
4010UDCI version. Check the version of the AV Amp, and then on the GUI Menu, set "DENON LINK
Setup" -"DENON LINK Mode" (l2i1"page 28)
If the OBP-401 OUDCI and AV Amp versions do not match, audio cannot be output correctly.
•Check the video terminals and make the connection to one of them.
•When connecting using the component video outputs, press (=l and set it to "HOMI Off".
AVAmp
-VIDEO-
I/IIlEO IN' _
,'. ~ ~"'''-9[J' :::--=:[:EP ----i-I
Connection to an AV Amp with No HDMI Video Input
I
I·~[·i'.
I :NON LINK does not support BD audio transmission.
•DENON LINK supports digital transmission up to 24 bit/2 ch at 192/176.4 kHz, and up to 24 bit/6 ch
at 96 kHz or less.
•When you have made aDENON LINK connection, the DBP-4010UDCI's speaker setting becomes
invalid. (Make the speaker setting on the connected AV Amp)
•DENON LINK 2nd cannot transmit multi/stereo area audio of Super Audio CD.
AVAmp
-AUDIO-
~
HOMI
IN
ld
C§J
DENDNlINK
tiJ
D
DENON LINK Connection CD Making aJitter-free Connection
m
-N,na
•When using DENON LINK 4th functions, press the (~l and set to "HDMI On".
•The jitter·free function does not work except during BD playback. In this case, the video signal is
output from the HDMI OUT terminal, and the audio signal from the DENON LINK terminal.
IWhen you connect the DBp·4010UDCI to aDENON LINK 4th compatible AV Amp uSing DENON ,
ILINK cable and HDMI cable, during BD playback the DBP·4010UDCI's circuit operates with the AV '
Amp's master clock signal. (The clock control indicator of the DBP-4010UDCI lights.) This enables
transmission of high-quality digital audio with minimal jitter.
.'
I
17