DENT-X 810 Basic User manual

Automatic
X-Ray Film
Processors
P/N 801-050253
Installation, Operation and Maintenance Manual
810 Basic
(Includes Dent-X 9000)
®
Visionary Imaging

NOTE: Use of DENT-X Chemistry is strongly recommended for
optimum processor performance and highest quality diagnostic
information.
TABLE OF CONTENTS
I. Safety Information & Labels Page
Safety Information (English) 1
Safety Information (French) 2
Safety Information (German) 3
Safety Information (Spanish) 4
Safety Information, Literature 5
Labels 6-15
II. General Description
Introduction, Description of Major Components 16
Control Module, On/Off Power Switch, Case & Covers 17
Main Frame, Washer/Dryer Module, Transport Modules, etc. 18
Processor, Exploded View (9000 Shown) 19
Optional Accessories, (Loader, Recirculator, Mounting Base, Stand) 20
Utilities & Pre-Installation Requirements, Safelighting 21
III. Installation
General, Unpacking, Assembly & Installation for Countertop 22
Daylight Loader, Initial Test Procedure (Without Chemistry) 23
Initial Test Procedure (Without Chemistry) Cont. 24
IV. Preparation for Use
Materials, Safelighting, Loading Replenisher & Solution Tanks 25
V. Operation
Operating Instructions 26
Operational Test Procedure, Precautionary Note, 27
Theory of Operation (9000) 27
Theory of Operation (9000 Cont.) 28
Theory of Operation (810 Basic) 29
VI. Maintenance
Daily Maintenance Procedures, Weekly Maint. Procedures 30
Weekly Maintenance (Cont.), As Required 31
Monthly Maintenance Procedures 32
Monthly Maintenance (Cont.), Control Module 33
VII. Troubleshooting Guide (9000 & 810 Basic) 34
VII. Troubleshooting Guide (9000 Only), Common Processing Problems 35 - 36
VIII. Calibration
Temper atur e, Tr ansp ort t im e 37
Replenishment System Calibration, (9000 Only) 38
VIII. Specifications 39

WARNING: Study manual thoroughly before attempting to install or
operate processor. Failure to do so could result in improper operation
which may lead to operator injury or damage to processor.
IMPORTANT: Complete and mail enclosed warranty card promptly
after equipment installation to ensure required factory warranty
registration.
LIST OF ILLUSTRATIONS
Figure 1: Major Machine Components (810 Basic shown) 16
Figure 2: Major Internal Components 16
Figure 3: 9000 & 810 Basic Control Panels 17
Figure 4a. Processor with Water Recirculator & Chemical Drain Kit 18
Figure 4: Processor, Exploded View (9000 shown) 19
Figure 5: Panoramic Daylight Loader 20
Figure 6: Processor Stand 20
Figure 7: Processor Mounting Base 20
Figure 8: Water Recirculator Unit 20
Figure 9: Location of Drain Hole 21
Figure 10: Attaching Drain Hose 22
Figure 11: Connecting Water Inlet Hose 22
Figure 12: Connecting Cable to SOL receptacle 22
Figure 13: Lifting up Film Sensor Bar (9000 Only) 23
Figure 14: Removing Developer Transport Module 23
Figure 15: Inserting bolts through holes in front of Processor 23
Figure 16: Attaching Loader 23
Figure 17: DENT-X Chemistry 25
Figure 18: Filling Replenisher Tanks 25
Figure 19: Loading Fixer Solution 25
Figure 20: On/Off Power Switch 26
Figure 21: Depressing Time Button (810 Basic Shown) 26
Figure 22: Development Time Chart 26
Figure 23: Guides for Intraoral Film 27
Figure 24: Pressing RUN Button 27
Figure 25: Removing the Film Sensor Bar Assembly 31
Figure 26: Removing the Developer Transport Module 31
Figure 27: Heater/Fan Assembly Plug 31
Figure 28: Slide out Heater/Fan Assembly 32
Figure 29: Washing Rollers 32
Figure 30: Pulling out Drain Plug 32
Figure 31: Lubricating Main Frame 32
Figure 32: Drive Shaft Coupling 32
Figure 33: Uncoupling Water Line Hose 32
Figure 34: Lifting out Washer/Dryer Module 32
Figure 35: Inside Cover Decal 37
Figure 36: Logic/Power Board (9000 Shown) 38
Figure 37: Dimensions - Top & Side View 39

IMPORTANT SAFETY INFORMATION
TO REDUCE THE RISK OF INJURY OR ILLNESS, READ, UNDERSTAND, AND HEED THE INFORMATION ON
THIS SHEET, ALL PRECAUTIONARY LABELS ON THE EQUIPMENT, AND ALL INSTRUCTIONS INCLUDED
WITH THE EQUIPMENT BEFORE ATTEMPTING INSTALLATION, USE, OR MAINTENANCE.
WA RN IN G: S ER IO U S B OD ILY I NJ URY can result from improper handling or usage.
WA RN IN G: N EV ER move the equipment without enough help and/or lifting tools.
WARNING: ALWAYS use care when opening the shipping carton. Strapping bands can snap
and injure you.
WA RN IN G: N EV E R operate the equipment without its protective panels and guards installed.
Beware of rotating gears and belts, rollers, and chains, and keep from becoming entangled in
them.
DANGER: POTENTIALLY FATAL VOLTAGES ARE PRESENT IN THIS EQUIPMENT.
CAUTION: NEVER make electrical connections to the equipment unless you are a qualified
electrician.
WA RN IN G: A LWAY S route power supply wiring through a nearby disconnect device.
WA RN IN G: N EV E R attempt electrical service on the equipment unless you are a qualified
electronics technician.
CAUTION: ALWAYS shut off power at the disconnect device before making electrical connec
tions or servicing electrical components.
CAUTION: ALWAYS replace fuses with those of the same type and rating.
WA RN IN G: N EV ER touch supply voltages; THEY CAN BE LETHAL.
CAUTION: NEVER operate the equipment until it is reliably electrically grounded, NOT through
the water system.
PROCESSORS AND PROCESSOR ACCESSORIES


DANGER! POISON! 

 PROCESSING CHEMICALS MAY BE HARMFUL OR FATAL IF
SWALLOWED. KEEP OUT OF REACH OF CHILDREN.
Always review and follow the hazard warnings and the ventilation, use and disposal instructions of the
chemicals manufacturer. Install all fluids correctly before operating.
CAUTION: TO AVOID POSSIBLE DRINKING WATER CONTAMINATION, make certain that
all plumbing complies with local codes.
WA RN IN G: P RO C ES SI NG CH EM I CA LS C AN C A US E SE VE RE BU RN S. Do not get in eyes, on
skin, or on clothing. Avoid breathing vapor, mist or dust, and use only with adequate ventilation. ALWAYS
FOLLOW THE SAFETY RECOMMENDATIONS OF THE CHEMICALS MANUFACTURER.
I. Safety Information & Labels
Safety Information
1

RECOMMANDATIONS IMPORTANTES
AFIN DE RÉDUIRE TOUS RISQUES DE BLESSURES OU DE MALAISES, LIRE ATTENTIVEMENT ET
APPLIQUER LES RECOMMANDATIONS INSCRITES SUR CETTE PAGE, SUR LES ÉTIQUETTES COLLÉES
SUR L’APPAREIL AINSI QUE LE MANUAL D’UTILISATION FOURNI AVEC CET APPAREIL, AVANT TOUTE
INSTALLATION, UTILISATION ET MAINTENANCE.
AV E R T I S S E M E N T : risque de blessures grâves en cas de mauvaises manipulation ou utilisation de
l’appareil.
AV E R T I S S E M E N T : ne JAMAIS déplacer l’appareil sans être suffisament aidé ou muni d’outils adéquats.
AV E R T I S S E M E N T : être TOUJOURS prudent lors de l’ouverture des cartons d’emballage. Les rubans de
cerclage peuvent blesser en se cassant brutalement.
AV E R T I S S E M E N T : ne JAMAIS utiliser l’appareil sans ces couvercles et panneaux de protection. Atten-
tion à ne pas être grippé par les pièces en mouvement (engrenages, courroies, rouleaux et chaînes).
DANGER : PRESENCE POSSIBLE DE TENSION ELECTRIQUE MORTELLE DANS CET APPAREIL.
AV E R T I S S E M E N T : ne JAMAIS effectuer la connexion électrique de l’appareil à moins d’être électricien
qualifié.
AV E R T I S S E M E N T : TOUJOURS connecter le câble d’alimentation au coupe-circuit le plus proche.
AV E R T I S S E M E N T : ne JAMAIS faire d’interventions électriques à l’intérieur de cet appareils à moins
d’être technicien qualifié en électronique.
ATTENTION : TOUJOURS couper le courant avant toutes connexions électriques ou dépannage de
composants électriques.
ATTENTION : TOUJOURS remplacer les fusibles défectueux par des fusibles de même valeur et de
même calibre.
AV E R T I S S E M E N T : ne JAMAIS toucher les fils d’alimentation électrique, cela peut être mortel.
ATTENTION : ne JAMAIS utiliser l’appareil tant qu’il n’est pas relier à la terre (mais pas par l’intermédiaire
des canalisations d’eau).
MACHINES A DEVELOPPER ET ACCESSOIRES


DANGER ! POISON ! 

 MANIPULER LES PRODUITS CHIMIQUES PEUT ETRE
DANGEREUX OU MORTEL S’ILS SONT AVALES. GARDER HORS DE PORTEE DES
ENFANTS. Toujours suivre attentivement les instructions des fabricants de produits chimiques
(indiquées sur les étiquettes et sur la documentation) concernant leur utilisation et leur évacuation. Veiller
aussi à avoir une ventilation suffisante. Installer correctement les différents liquides avant utilisation.
ATTENTION : AFIN D’EVITER TOUTE CONTAMINATION DES EAUX POTABLES, s’assurer
que toutes les canalisations et raccords de plomberie sont en accord avec la législation locale.
AV E R T I S S E M E N T : MANIPULER LES PRODUTS CHIMIQUES PEUT CAUSER DE SEVERES
BRULURES. Ne pas mettre en contact avec les yeux, la peau et les vêtements. Eviter de respirer les
vapeurs, émanations et poussières, et utiliser uniquement avec la ventilation adéquate. TOUJOURS SUIVRE
LES RECOMMANDATIONS DE SECURITE FOURNIES PAR LES FABRICANTS DE PRODUITS
CHIMIQUES.
Safety Information (Cont’d)
2