Denver Electronics SCO-65220 User manual

User manual
SCO-65220
facebook.com/denverelectronics
Before operating this vehicle, read all the instructions for safe assembl and operations. User’s manual can guide ou through the
functions and usage of Electric scooter. Before using this Electric scooter, familiarize ourself with how to operate, so that ou can
keep the Electric scooter in the best condition possible.
This appliance can be used b children aged from 14 ears and above and persons with reduced ph sical, sensor or mental
capabilities or lack of experience and knowledge if the have been given supervision or instruction concerning use of the appliance in
a safe wa and understand the hazards involved.
Children shall not pla with the appliance.
Cleaning and user maintenance shall not be made b children without supervision.
Version 1.0
1

Table of Contents
2

1. Product and Accessories
IMPORTANT:
This Electric scooter must be charged and stored in a safe place.
For safet reason and batter performance, never charge the Electric scooter in the temperature below 5°C or above 45°C. Onl use
the charger included to charge the Electric scooter. Alwa s disconnect the charger after the Electric scooter is full charged.
3

2. Unfold/fold t e Electric scooter
Unfold the Electric scooter
1) Stand the Electric scooter on its wheels, and press the unlock clasp.
2) Pull up the handle in a gentle wa .
3) The Electric scooter is unfolded as soon as ou hear the rod click into place.
Fold the Electric scooter
1) Hold the clasp and pull it outward
2) Press the front tube of Electric scooter downward (Attention: the limit position must be put right.)
3) The rod clicks audibl into place.
4

4) Dual action safet knob
Press the red button to fold or unfold the Electric scooter.
Rotate the safet knob to the “FOLDING” position on the left or right, then press the red button to fold our Electric scooter. Rotate
the safet knob to the “RIDING” position, ou can start our driving.
The knob must be set to the “RIDING” position when riding for safet issue to prevent unintended folding the Electric scooter.
3. Handle bar assembly
1) Parts inside the packaging: two handlebars
2) Change displa angle: Loosen the screw on the handlebar, and rotate the axle to make the handlebar meter
screen upwards while the and displa screen turn inwards in a horizontal level. Remember to tighten screws again
3) Before operating the electric scooter, turn the handlebar grips, and carefull check all the components to make sure that the
steering is correctl installed as described above, and that all connecting parts are secure and full functional.
Figure 1 Figure 2
5

4. Connect t e c arger
Plug the supplied adapter into the charging port.
6

5. Intended Use
The Electric scooter is neither a means of transport nor sports equipment, but a device for personal entertainment. The Electric scooter for
domestic use onl and onl b a person aged at least 14 with a maximum weight of 100 kg. The other parameters for the permissible operation
of the Electric scooter are defined in the section (“10. List of parameters”) . Importantl , the Electric scooter ma onl be operated in good
visibilit conditions and onl if the ph sical conditions for stabilit on the Electric scooter are met (for example, not on one leg/not under the
influence of drugs or alcohol). When operating the Electric scooter, the operator must wear personal protective equipment specified in the
section (“13. Warnings” > 13.2 Preparation”).
6. Safety Instruction
We recommend alwa s wearing helmet and protective gear like elbow, knee and wrist protectors to ensure our personal safet .
Also make sure ou have read the user manual carefull , to ensure ou know how to ride it in a safe and fun wa .
The Electric scooter is for domestic use onl .
It is our responsibilit to be aware of and compl with all regulations in our countr . If there are no regulations for this Electric
scooter in our countr , please take care of our own safet and the safet of others.
Also pa attention to other people. Alwa s ride safel and onl at a speed that allows ou to brake safel at an time. A common
thing for such products is that there is a risk that ou ma fall off the product and injure ourself. Alwa s ride as safel as possible.
If lending the Electric scooter to friends and famil , please make sure the use proper protective gear and know how to ride it.
Before riding the Electric scooter, please check that all parts are working as supposed to. If an loose parts, abnormal noise, reduced
batter life etc. are detected, please contact our retailer for product service and warrant . Do not repair the Electric scooter ourself.
Inspect the rear tire, rear brake, and brake pad according to Section 7 of the maintenance specification in this operating instructions.
The Electric scooter ma become unstable if the rear brake is deformed or loose. This is because the distance between the brake pad
and the rear wheel becomes too small, possibl leading to a blocked rear wheel.
Avoid appl ing too much force or stepping on the rear fender permanentl . This ma cause the fender to loosen or damage the spring
holding the fender.
As a result, the brake pad constantl touches the wheel and the motor temperature increases due to the additional resistance. The rear
tire can also get loose if the brake is in constant braking position.
Avoid constant braking. As a result, the tires will not onl wear off, but also become hot. This will soften the rubber and it will no
longer have the same grip on the road as usual. Do not touch the tire after braking.
If ou hear unusual noises or notice friction when switching on the Electric scooter, a bearing ma be damaged. A worn bearing ma
even be indicated b strong vibration of the handlebar. In this case, please contact our retailer since the bearing needs to be replaced
and/or the handlebar checked and adjusted.
Ride the Electric scooter onl on a dr surface since otherwise the riding safet and braking performance ma be impaired and the
motor or bearings ma be damaged.
Please do not ride up or down long and steep slopes.
Stop riding when ou receive the "Low Batter Warning". The Electric scooter then moves onl slowl and does not have the same
traction as normal and the electric brake does not work. In this case, please use the rear brake to stop the Electric scooter. Get off the
scooter as soon as the speed allows to do that safel .
Do not use the electric brake and the throttle at the same time.
A normall working Electric scooter operates safel and quietl . If ou hear noises or notice bump operation, please check wheels,
bearings, and brakes. Contact our customer service for repair and maintenance, if necessar .
7

7. Maintenance
•Storage and cleaning
If our Electric scooter gets dirt , please clean it with a damp cloth. ( ou can use a stiff brush first to get the worst dirt off and then
use a cloth afterwards to clean it.). It is also possible to use a little toothpaste if the dirt is stuck. Remember to clean with damp cloth
after this.
Please make sure to keep the Electric scooter turned off while cleaning it, and make sure to cover the charging input to avoid
problems with the electronics.
Please notice: Do not use alcohol, gas, kerosene or other corrosive and volatile chemical solvents. This can damage both the
appearance and the internal structure of the Electric scooter. You ma not use pressured water-gun or running water either.
Please store our Electric scooter in a dr and cool environment when not in use. Avoid leaving it outdoors, as it is not made for use
in wet areas. Nor is it good to expose to high temperatures caused b direct sun for a long time.
•Maintenance of batteries
Please make sure the batteries do not get over 50° Celsius, or minus 10° Celsius for a longer period of time. (e.g. don’t leave the
Electric scooter in a hot car in summer, do not put batteries into fire et.) Low temperature (e.g. subzero temperature) can damage the
batter cells.
Keep the Electric scooter awa from open flame or other sources of heat to prevent the batter from getting too hot. Also make sure
not to leave the Electric scooter at freezing temperatures. Both heat and excessive cold can cause the batter to discharge.
Please avoid draining the batteries 100%. It is best to charge them while there is still power on them. This will extend batter life.
Also if riding the Electric scooter in cold or ver hot areas, the batter time can be lower than when riding in temperatures from 15-
25° Celsius. This is not a failure on the batteries, but normal behavior.
Do not overcharge and discharge the batter .
Make sure that the batter is charged at regular intervals, even if ou do not use the Electric scooter for a long time. This is to prevent
damage to the batter caused b low voltage over an extended period.
Please notice: Even full charged batteries will run out of power if the Electric scooter is not used for a period of time. Expect
between 90 and 120 da s in off mode if batteries are full charged. If onl partiall charged, this period of time is lower.
Please make sure to charge the batteries before the are 100% out of power, to avoid damaging the batter cells. (damaged batter
caused b wrong handling are not covered b warrant )
It is forbidden to disassemble batter package. This is onl to be handled b official service repair centers and professionals.
•Maintaining bearings
The Electric scooter has sealed and dustproof bearings so that no lubrication is required. Check the bearings for wear at regular
intervals to avoid unsafe riding. Do not jump on and off and do not appl excessive force otherwise to avoid damage to the bearings.
This is not a sports Electric scooter.
•Maintaining wheels
Check the wheels for wear at regular intervals to avoid unsafe riding.
•Maintaining the brake
The brake pad is made of metal. Check the brake pad for wear at regular intervals to avoid unsafe riding. Do not appl excessive
force to avoid damage to the brake.
•Maintaining screws and other fasteners
Make sure that all screws are properl tightened to avoid unsafe situations.
8

•Please make sure to check that the steering s stem is correctl adjusted and that all connection components are firml secured
and not broken before riding, refer to handlebar assembl and safet instruction.
•Please read operation guide and warnings of correct techniques for use and braking
•Alwa s wear shoes;
•When self-locking nuts and other self- locking fixings ma lose their effectiveness
•All parts and materials' qualit of electric scooter can not be changed, modifications are not allowed
9

8. Operational control
For better operation, please read the instructions carefull .
8.1 Button
There are three buttons in the displa , Power button, ▲ Speed up button and ▼ speed down button.
8.2 Control and display
10

Power On: Long press the power button until the displa lights up.
Power Off: Long press the power button until the displa goes out and the s stem is off.
1. Batter power displa : it shows the current remaining batter capacit .
2. Power off automaticall : After the displa is idle for more than 5 minutes, the Electric scooter automaticall turns off.
Change displa information: When the Electric scooter is on, short press the power button , change the showing data on
the displa , TIME, ODO, DIS and other characters respectivel . When it is showing time, it indicates the running time after
switching on. The time will be cleared after switching off. When it is showing DIS, it indicates the driving distance after
switching on, and it will be cleared after power off. When it is showing ODO, it indicates the total mileage, which will be
retained unless it is manuall cleared.
Change the gear: Short press ▲ or ▼ button to change the gear level (Gear 3 is fast speed, Gear 2 is medium speed, and Gear 1
is slow speed).
Deceleration: Gentl press the deceleration dial to slow down. The deeper the press, the greater the deceleration (the
deceleration is relevant to the formation of the press, and pushing too hard cannot increase the braking force and ma cause
damage to the brake dial).
Clear total mileage: Press ▲ and ▼ buttons at the same time, then press the power button to switch on the Electric
scooter, and the total mileage will be cleared.
Important: Press ▲and ▼ buttons at the same time, then press the power button and select P3 mode, when parameter value
is 0, it will start with zero. When parameter value is 1, it will start with non-zero.
(Zero start: When starting, the Electric scooter in a stationar case, press the accelerator to start driving.)
(Non-zero start: When starting, the scooter is static, press the accelerator and the Electric scooter does not work, push the Electric
scooter manuall to start driving, the Electric scooter works. factor default is non-zero start.)
You have to manuall move the Electric scooter with our foot before the accelerator handle are working.
9. Riding Electric scooter
1. Press ▲ and ▼ buttons to adjust speed level.
11

2. Press the accelerator button to accelerate, so ou can drive；
3. Press the brake button to brake；
4. When ou press the accelerator and electric brake button at the same time, the Electric scooter will automaticall brake;
5. For safet , the rear wheel brake s stem must be used when driving at high speed.
6. When driving at night, press the headlight switch button to turn on the headlight.
12

9.1 Front and back LED lamps
This Electric scooter is equipped with the front and back LED lamps. The front lamp lights white and the back lamp lights red.
Both of the LED lamps needs 2 t pe AA batteries (not included) for operation.
1) Detach the front and back LED lamps from the Electric scooter.
2) Open the LED housing b using a coin. Insert 2 t pe AA batteries, and close the housing.
3) Re-attach the front and back LED lamps to the Electric scooter.
Press “PUSH” to turn the light on/off.
Press ”PUSH” one time to make the lamp flash.
Press ”PUSH” a second time and the LED lamp turns to solid light from flashing.
Press “PUSH” again to turn the LED lamp off.
13

10. List of parameters
Parameter Range
Size Folding size (m) 1.08*0.42*0.28
Developed size (m) 0.97*0.42*1.08
Carton size (m) 1.13*0.22*0.33
Weight Max load (kg) 100
Net Weight (kg) 9.76
Ride Condition Age (Year) 14+
Electric scooter Max. speed (horizontal riding) (km/h) 20
Max traveling distance (km) 12
Terrain Level and dr surface
Batter
T pe: Li-ion batter
Nominal voltage (V) 25.2
Input voltage (V) 29.4
Batter capacit (mAH) 4000
Motor Motor Power (W) 300
Emission sound pressure level (DB) Emissions < 70 db (A).
Batter Charger Rated input voltage(V) 100-240
Rated output voltage(v) 29.4
Rated current (A) 1.5
Charging Time(h) 3
Electric scooter
Model: SCO-65220
Input: 100V-240V~, 50/60Hz, 1.5A (Max)
Output: 29.4V 1.5A
Max Speed: 20km/h
Weight: 9.76 kg
Year Of Construction: 2019
Max Load: 100kg
Batter : 25.2V/4Ah
Power Consumption: ≤300W
Please charge the Electric scooter with the original charger XHK-922B-29415.
DENVER ELECTRONICS A/S
Omega 5A Soeften DK-8382 Hinnerup
Denmark
denver-electronics.com
14

11. Electric scooter safe parking
Once ou have stopped the Electric scooter, get off it and press the side stand down with our right foot to support the Electric
scooter. The side stand is located on the left-hand side of the Electric scooter below the foot board.
Before ou ride again, push the side stand back up so that it is parallel to the foot board.
12. Safe transportation
Pack the Electric scooter flat, don’t drop the Electric scooter during the transportation, forbid to put the Electric scooter near fire or
explosive materials.
13. Warnings
13.1 Risks of riding
First, learn safe riding before ou ride the Electric scooter fast.
-Failure to observe, loss of control, falls, and violations of the rules can cause injuries.
-Speed and range depend on the rider's weight, terrain, temperature, and riding st le.
-Wear a helmet and protective clothing when riding the Electric scooter.
-Read the operating instructions carefull before riding the Electric scooter.
-For use onl in a dr environment.
-The Electric scooter ma not be used on public roads.
-Make sure that this product complies with local regulations.
-For domestic use onl
13.2 Preparation
-First, charge the batter completel .
-Wear a helmet, knee and elbow pads, as well as earmuffs/earplugs.
-Do not wear loose clothing or open laces that can get caught in the Electric scooter wheels.
13.3 Weig t restriction
Reason for the weight restriction:
•Ensuring the rider's safet ;
•Avoiding damage due to overload.
Maximum capacit : 100kg.
Do not tr to make a turn too fast.
Lithium batter inside.
If the Electric scooter switches off, the s stem will block the vehicle automaticall .
It can be released again b pressing On/Off.
•Use the device onl at temperatures between -10 °C and +45 °C.
13.4 Range per c arge
The range depends on several factors:
•Topograph : On level paths ou have a greater range than on uneven ground.
•Weight: The range depends on the rider's weight.
•Temperature: Extreme temperatures reduce the range.
•Maintenance: If the Electric scooter is charged properl and the batter is kept in good condition, the range will be extended.
•Speed and riding st le: The range is greater at constant speed than at frequent stops and starts, acceleration and braking.
13.5 Safe riding
This chapter focuses on safet , experience, and warnings. Before operating the vehicle, please read all installation and operating
instructions carefull .
Familiarize ourself with the vehicle before ou use it so that ou can keep the Electric scooter in sound condition.
15

•Observe all safet instructions when riding the Electric scooter.
•The Electric scooter is designed onl for personal entertainment. Avoid operating it on public roads/in road traffic.
•Children, elderl people, and pregnant women are not allowed to ride the vehicle.
•People with limited sense of balance are not allowed to ride the Electric scooter.
•Avoid riding the Electric scooter under the influence of alcohol or other substances.
•Do not carr an objects while riding.
•Make sure ou have a clear vision in front of ou to ride the Electric scooter safel .
•While riding, our feet must alwa s be on the foot board.
•The Electric scooter can accommodate onl one person.
•Do not start or stop abruptl .
•Avoid riding on steep slopes.
•Stop riding the Electric scooter if ou hit against a solid object (such as a wall or other structure) with it.
•Do not ride in diml lit or dark places.
•Ride the Electric scooter at our own risk, we assume no liabilit for accidents or damage.
•Ride at a safe speed that allows ou to stop at an time.
•Keep the Electric scooter at a sufficient distance from other people and avoid collisions.
•Steer through balance shifting, fast movement can result in falls.
•Do not ride in rain or under other wet conditions. Ride onl in dr weather.
•Avoid riding over obstacles, if possible, and avoid snow, ice, and slipper surfaces.
•Avoid riding over textiles, small branches, and stones, if possible.
•Avoid riding in narrow places or in places with obstacles, if possible.
•Jumping on and off the Electric scooter will cause damage that is not covered b the warrant . There is a risk of injur . Injuries
and damage due to "trick riding" are not covered b the warrant .
13.6 C arging
•Make sure that the Electric scooter, charger, and DC power input of the device are alwa s dr .
•Note: To charge this Electric scooter, use SOLELY the supplied XHK-922B-29415 charger with the following output: 29.4 V -
1.5 A.
•Using a different charger ma cause damage to the device and other potential risks.
•Use the mains adapter to plug the DC input of the device into a conventional socket.
•Make sure that the green indicator on the mains adapter is on.
•The red indicator lights up when properl charged; if this is not the case, please check the connections.
•If the indicator on the charger switches from red to green, the batter is full charged.
•Now ou can stop the charging c cle. Overcharge shortens the batter life.
•The charging process takes up to 3 hours. Do not charge the batter for more than 3 hours. After 3 hours, disconnect the charger
from the device and the power suppl . Overcharge reduces the batter service life.
•The product must not be charged over extended periods.
•Alwa s keep an e e on the device throughout the charging c cle.
•Charge the device onl at temperatures between 0 °C and +45 °C.
•When charging at lower or higher temperatures, there is a risk that the batter performance will be reduced; therefore, there is a
potential risk of injuries and material damage.
•Store and charge the device in an open, dr area awa from combustible materials.
•Do not charge the device in direct sunlight or in the vicinit of open flames.
•Do not charge the device immediatel after use. Allow the device to cool down for an hour before charging it.
•If the device is left to other people, it must be charged partiall (20 - 50%), not full .
•Do not remove the device from its package to full charge it and then put it back in the package.
•The device is generall partiall charged as shipped from the factor . Keep the device partiall charged until it is used.
•Allow the Electric scooter to cool down for at least 1 hour before it can be put in the package.
•Do not leave the device exposed to sunlight in a car.
16

The Electric scooter must not be used during the charging c cle!
•The LED indicator on the batter charger lights red during the charging process.
•The LED indicator on the charger will light green when the charging process is complete.
•After charging, disconnect the charger from the mains and the Electric scooter.
Connect the DC cable supplied with the Electric scooter onl to the DC input!
•Do not insert foreign bodies into the DC input.
•Do not remove the protective cap from the DC input!
•Remove the cap onl when charging the Electric scooter!
•After charging, disconnect the DC plug and close the DC input again with the cap!
Make sure that neither water nor other liquids penetrate into the inner components of the Electric scooter; otherwise, the
electronics/batteries of the device could be permanentl damaged. There is a risk of injur .
•If ou open the Electric scooter casing, the warrant will become null and void.
•Alwa s keep the protective cap plugged onto the DC connector!
•Onl take off the cap when charging the Electric scooter!
•After charging, take out the DC plug and put on the protective cap onto the DC connector again!
•Make sure to wear helmet and protective clothing before using the Electric scooter.
•Make sure to read manual carefull before using the Electric scooter.
•The Electric scooter is not intended for use on public roads nor in traffic
•The Electric scooter must onl be used on dr and level ground
•For domestic use onl
•The Electric scooter ma not be used b an one under age of 14 ears
17

Please notice - All products are subject to change without an notice. We take reservations for errors and omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to our
health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctl .
Electric and electronic equipment and batteries is marked with the crossed out trash can s mbol, seen below. This s mbol signifies
that electric and electronic equipment and batteries should not be disposed of with other household waste, but should be disposed of
separatel .
As the end user it is important that ou submit our used batteries to the appropriate and designated facilit . In this manner ou make
sure that the batteries are rec cled in accordance with legislature and will not harm the environment.
All cities have established collection points, where electric and electronic equipment and batteries can either be submitted free of
charge at rec cling stations and other collection sites, or be collected from the households. Additional information is available at the
technical department of our cit .
DENVER ELECTRONICS A/S
Omega 5A, Soeften
DK-8382 Hinnerup Denmark
facebook.com/denverelectronics
18

Regarding Batter charging SCO-65220
Important – Please read!
Dear customer. We hope ou get a lot of jo out of our new Electric scooter.
The batter built in the Electric scooter is not full charged from production line. And when left unused the batter can slowl
discharge b itself.
This can lead to slow charge if the batter is full discharged, but this is done to avoid damage to the batter .
If you experience t at you cannot turn on your Electric scooter, and it doesn’t seem to c arge (t e c arger
lig ts up green instantly), t en please do t e following.
1. Leave the charger in for 6-7 hours. This will make sure the batter will be full charged again (it can take 3-4 hours before
it starts normal charging).
2. If this does not solve our problem, please ride the Electric scooter manuall without turning it on. Use our legs to give
speed, for around 100 m, and then connect the charger. The engine in the front wheel will this wa help to activate the
charging function and it will charge normall . (full charge takes 2-3 hours if using this wa )
Please enter: www.denver-electronics.com to obtain the electronic version of the manual.
19

WARNINGS
Please read t e manual completely and t e instructions below before using t e product.
Product names: SCO-65220
Product t pe: Electric scooter
Year of manufacturing: 2019
•Note: ONLY use the supplied charger labelled XHK-922B-29415 with the following output voltage to charge this Electric
scooter:29.4V – 1.5A.
•Using another charger ma damage the product or create other potential risks.
•Never charge the product without supervision.
•The charging period of the product should not exceed four hours. Stop charging after four hours.
•The product should onl be charged in temperatures between 0°C and 45°C.
•If charging at lower or higher temperatures, there is a risk that the performance of the batter will be reduced and a potential risk
of damage to the product and personal injur .
•The product should onl be used in temperatures between -10°C and +45°C.
•If used at lower or higher temperatures, there is a risk that the performance of the batter will be reduced and a potential risk of
damage to the product and personal injur
•Store the product at temperatures between 0°C and 35°C. (optimum storage temperature is 25°C)
•Charge and store the product in an open, dr area and awa from flammable materials (i.e. materials that ma burst into flames).
•Do not charge in sunlight or near open fire.
•Do not charge the product immediatel after use. Let the product cool down for one hour before charging.
•If the product is left with other persons for example during a holida period, it should be partiall charged (20-50% charged).
Not full charged.
•Do not remove the product from the packaging, charge it full and then put it back into the packaging.
•When shipped from the factor , the product has often been partiall charged. Keep the product in a partiall charged state, until
it is going to be used.
DENVER ELECTRONICS A/S
Omega 5A, Soeften, 8382 Hinnerup, Denmark
www.denver-electronics.com
20