DEVI DEVIreg 610 User manual

DEVIreg™ 610
Electronic Thermostat
Installation Guide
www.DEVI.com

Table of Contents
1 Introduction ............... 3
1.1 Technical Specifications ..... 4
1.2 Safety Instructions ........ 5
2Mounting Instructions ......... 6
3Warranty ................. 11
4 Disposal Instruction .......... 11
1 Introduction
DEVIreg™ 610 is an electronic thermostat to be installed di-
rectly on the wall. It is provided with a 2-pole switch and a
wire sensor to control the desired temperature.
The thermostat has a button for adjusting the temperature
setting with a scale from -10° to +50°C, and an LED indica-
tor that shows standby periods (green light) and heating
periods (red light).
More information on this product can also be found at:
devireg.devi.com
DEVIreg™ 610
Installation Guide 3

1.1 Technical Specifications
Operation voltage 220-240V~, 50Hz
Standby power consumption Max. 0.93W
Relay:
Resistive load
Inductive load Max 10A / 2300W @ 230V cos φ= 0.3 max 1A
Sensing units NTC 15kOhm at 25°C
Sensing values:
0°C
25°C
50°C
42kOhm
15kOhm
6kOhm
Hysteresis ± 0.2°C
Ambient temperature 10°C to +50°C
Temperature range -10°C to +50°C
Cable specification max 1x4mm2or 2x2,5mm2
Ball pressure temperature 75°C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20°C to +65°C
IP class 44
Protection class Class II -
DEVIreg™ 610
4 Installation Guide

Dimensions 100 x 69.5 x 45mm
Weight 165g
The product complies with the EN/IEC Standard "Automatic
electrical controls for household and similar use":
▪EN/IEC 60730-1 (general)
▪EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
Please also note the following:
▪The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
▪The thermostat must be connected to a power supply
via an all-pole disconnection switch.
▪The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
▪Always connect the thermostat to continuous power
supply.
▪Do not expose the thermostat to moisture, water, dust,
and excessive heat.
DEVIreg™ 610
Installation Guide 5

2 Mounting Instructions
Please observe the following placement guidelines:
▪The thermostat can be placed both indoors and out-
doors.
▪Place the thermostat on a wall, pole, steel/wooden
plate or pipe.
In wet rooms, place the thermostat according
to local regulation on IP classes.
DEVIreg™ 610
6 Installation Guide

Follow the steps below to mount the thermostat:
1. Open the thermostat:
-10
10 30
50
C
I
0
-10
10 30
50
C
I
0
▪Set adjustment button to minimum temperature.
▪Loosen the 2 screws and open the front cover.
DEVIreg™ 610
Installation Guide 7

2. Fasten the thermostat:
▪Drive the screws through the holes in the bottom
corners of the thermostat.
▪Seal the holes with the enclosed screw stopper to
maintain the density.
DEVIreg™ 610
8 Installation Guide

3. Connect the thermostat according to the connection
diagram.
IP44
-10T50
D610
L N N NO NC NTC
Mains
220-240V~
L
N
Sensor
Max.Load
10 (1) A
▪Heating: (L-main, N-main, L-load, NO (normally open)
- load).
▪Cooling: (L-main, N-main, L-load, NC (normally
closed) - load).
The screen of the heating cable must be connected to
the earth conductor of the power supply cable by us-
ing a separate connector.
4. Reinstall the front cover.
5. Ensure that the adjustment button can be adjusted
within full temperature range, i.e. from -10°C to +50°C.
DEVIreg™ 610
Installation Guide 9

6. Install sensor using the supplied sensor cable - spec.
NTC 15 kΩ @ 25°C.
▪Press out the blanket located at the bottom of the
thermostat and insert the seal nipple.
▪Connect sensor to terminals 6+7.
The sensor cable can be extended up to 50 m with 1.5
mm² installation cable without affecting the accuracy
of the thermostat.
Do not place the cable parallel to other installation ca-
bles as undesirable signals may be induced.
The installation must be permanent.
If the sensor is to be built in, used for pipe applica-
tions, or exposed to pressure, always install it in a con-
duit.
7. Turn on the power supply.
DEVIreg™ 610
10 Installation Guide

3 Warranty
2
Y E A R
4 Disposal Instruction
DEVIreg™ 610
Installation Guide 11

DEVIreg™ 610
12 Installation Guide

DEVIreg™ 610
Installation Guide 13

DEVIreg™ 610
14 Installation Guide

DEVIreg™ 610
Danfoss A/S
Electric Heating Systems
Ulvehavevej 61
7100 Vejle
Denmark
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.DEVI.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its
products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes
being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. DEVI and the DEVI logo-
type are trademarks of Danfoss A/S. All rights reserved.
08095435 & VICKK302 Produced by Danfoss © 07/2012

DEVIreg 610 IP44
140F1080
220-240V~ 50-60Hz~ -10 to +50°C 10A/2300W@230V~ IP44
Product Documentation
DK EL 7224215344 SE EL 8581196 NO EL 5491490 FI SSTL 3531041
Designed in Denmark for Danfoss A/S
5 7 0 3 4 6 6 2 0 9 2 5 7