DEVI Devireg 330 User manual

DEVIreg™ 330
(+5 to +45°C)
Electronic Thermostat
Installation Guide
www.DEVI.com

Table of Contents
1 Introduction ............... 3
1.1 Technical Specifications ..... 4
1.2 Safety Instructions ........ 5
2 Mounting Instructions ......... 6
3 Settings ................. 7
4 Warranty ................. 8
5 Disposal Instruction .......... 9
1 Introduction
DEVIreg™ 330 is an electronic thermostat to be installed in
electric cabinets with DIN rail attachment. The thermostat
must be installed via an all-pole disconnection switch. Ei-
ther a floor sensor or an external room sensor must be used
to measure and control the desired temperature.
The thermostat has a button to adjust the temperature set-
ting with a scale from +5 to +45°C. An LED indicator shows
standby periods (green light) and heating periods (red
light).
More information on this product can also be found at:
devireg.devi.com
DEVIreg™ 330 (+5 to +45°C)
Installation Guide 3

1.1 Technical Specifications
Operation voltage 220-240V~, 50Hz
Standby power consumption Max 0.25W
Relay:
Resistive load
Inductive load
Max 16A / 3680W @ 230V
cos φ= 0.3 max1A
Sensing units NTC 15kOhm at 25°C
Sensing values:
0°C
25°C
50°C
42kOhm
15kOhm
6kOhm
Hysteresis ± 0.2°C
Ambient temperature 10°C to +50°C
Lowering in economy periods -5°C
Temperature range +5 to +45°C
Cable specification max 1x4mm2or 2x2,5mm2
Ball pressure temperature 75°C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20°C to +65°C
IP class 20
DEVIreg™ 330 (+5 to +45°C)
4 Installation Guide

Protection class Class II -
Dimensions 86 x 36 x 58mm
Weight 83g
The product complies with the EN/IEC Standard "Automatic
electrical controls for household and similar use":
ƒEN/IEC 60730-1 (general)
ƒEN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
IMPORTANT: When the thermostat is used to control a
floor heating element in connection with a wooden floor or
similar material, always use a floor sensor and never set the
maximum floor temperature to more than 35°C.
Please also note the following:
ƒThe installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
ƒThe thermostat must be connected to a power supply
via an all-pole disconnection switch.
ƒThe sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
DEVIreg™ 330 (+5 to +45°C)
Installation Guide 5

ƒAlways connect the thermostat to continuous power
supply.
ƒDo not expose the thermostat to moisture, water, dust,
and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
ƒInstall the thermostat in an electric cabinet with DIN
rail attachment or a separate DIN attachment accord-
ing to local regulation on IP classes.
ƒDo not place the thermostat in a way that it will be ex-
posed to direct sunlight.
Follow the steps below to mount the thermostat:
1. Click the thermostat on to the DIN rail attachment.
2. Connect the thermostat according to the connection
diagram.
IP20
10T50
8765
N
4321
L
Mains
220-240V~
250V~
16 (1) A
Sensor
D330
+5°C to
+45°C
-5°C
DEVIreg™ 330 (+5 to +45°C)
6 Installation Guide

The screen of the heating cable must be connected to
the earth conductor of the power supply cable by us-
ing a separate connector.
Note: Always install the floor sensor in a conduit in the
floor.
3. Turn on the power supply.
3 Settings
If a floor sensor is used, please be aware of the following:
ƒThe floor temperature is measured where the sensor is
placed.
ƒThe temperature of the bottom of a wooden floor can
be up to 10 degrees higher than the top.
ƒFloor manufactures often specify the max temperature
on the top surface of the floor (usually 27-28˚C).
ƒAlways use a floor sensor to control floor heating.
Without a floor sensor, the temperature control may
be less accurate and you risk overheating the floor.
DEVIreg™ 330 (+5 to +45°C)
Installation Guide 7

Thermal
resist-
ance
[m2K/W]
Examples of floor-
ing
Details Approximate
setting for
25˚C floor
temperature
0.05 8 mm HDF based
laminate
> 800 kg/m328˚C
0.10 14 mm beech par-
quet
650 - 800
kg/m3
31˚C
0.13 22 mm solid oak
plank
> 800 kg/m332˚C
< 0.17 Max. carpet thick-
ness suitable for
floor heating
acc. to EN
1307
34˚C
0.18 22 mm solid fir
planks
450 - 650
kg/m3
35°C
4 Warranty
2
2
YEAR
DEVIreg™ 330 (+5 to +45°C)
8 Installation Guide

5 Disposal Instruction
DEVIreg™ 330 (+5 to +45°C)
Installation Guide 9

DEVIreg™ 330 (+5 to +45°C)
10 Installation Guide

DEVIreg™ 330 (+5 to +45°C)
Danfoss A/S
Electric Heating Systems
Ulvehavevej 61
7100 Vejle
Denmark
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.DEVI.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its
products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes
being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. DEVI and the DEVI logo-
type are trademarks of Danfoss A/S. All rights reserved.
809 & VIGDQ02 Produced by Danfoss © 0/201

DEVIreg 330 +5<>+45°
140F1072
220-240V~ 50-60Hz~ +5 to +45°C 16A/3680W@230V~
Product Documentation
DK EL 7224215315 SEEL 8581185 NO EL 5491481 FI SSTL 3531031
Designed in Denmark for Danfoss A/S
5
7
03
4
66
2
0
922
6