DEVI DEVIreg 535 User manual

DEVIreg™ 535
Electronic Intelligent Thermostat
User Guide
www.DEVI.com

Table of Contents
1 Introduction ............... 4
1.1 Safety Instructions ........ 5
2Settings ................. 6
2.1 Increase/Decrease Preferred Tem-
perature .............. 7
2.2 Time and Day of Week ...... 7
2.3 Periods with Lowering of Temper-
ature ................ 8
2.4 Minimum Floor Temperature .. 14
2.5 Frost Protection ......... 15
2.6 Safety Lock ............ 16
2.7 Switching Between Floor and
Room Temperature ....... 16
2.8 Turning the Thermostat On and
Off ................. 17
3 Error Messages ............. 18
4 Warranty ................. 20
5 Disposal Instruction .......... 20
DEVIreg™ 535
User Guide 3

1 Introduction
DEVIreg™ 535 is a electronic timer temperature controller
specially designed for floor heating systems.
Once set, the thermostat automatically adjusts the heating
to meet your comfort levels regardless of changing weath-
er conditions by measuring the floor temperature and com-
bining it with the room temperature.
Even the programming of economy temperatures (i.e. low-
ering of temperature during the night and when you are
out of the house) is very simple. Just choose the pro-
gramme that fits your daily rhythm best.
Furthermore, the thermostat features a minimum floor
temperature setting, eg. for keeping your tile floors warm
in summer as well.
DEVIreg™ 535
4 User Guide

1.1 Safety Instructions
Please observe the following guidelines:
▪Do not cover the thermostat, e.g. by hanging towels or
similar items in front of it! This will impair the ability of
the thermostat to sense and adjust the room tempera-
ture correctly.
▪Do not spill liquids of any kind into the thermostat.
▪Do not open, disassemble, or tamper with the thermo-
stat in any way.
▪If the thermostat is installed in a place frequented by
small children, use the safety lock.
▪Do not interrupt the power supply to the thermostat.
▪The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
The thermostat has a safety
switch. When turned off, all
electrical supply to the ther-
mostat is disconnected.
DEVIreg™ 535
User Guide 5

2 Settings
Using clear visual symbols, the display of the thermostat
shows active and selected functions, the actual tempera-
ture and the time:
1. Days of week
2. Settings
3. Frost protection
4. Room temperature
5. Day rhythm periods and comfort / economy tempera-
ture
6. Actual temperature is displayed
7. Safety lock
8. Maximum / minimum temperature
9. Floor temperature
DEVIreg™ 535
6 User Guide

2.1 Increase/Decrease Preferred Temperature
How to increase or decrease the temperature
1. Press the arrow buttons ▲▼ to either
increase or decrease the temperature.
The temperature is changed in incre-
ments of 0.1°C.
2. Press the • button to accept.
Note: If the thermostat is configured to use a floor sensor
only, and you try to increase the temperature above the
maximum floor temperature limit, the corresponding sym-
bol will flash on the display.
2.2 Time and Day of Week
How to set the time and day of week
1. Press the clock pinhole with a small
screw driver, pencil, or needle.
The display now changes from tem-
perature to time display.
DEVIreg™ 535
User Guide 7

2. Press the • button and the hours start flashing. Use the
arrow buttons ▲▼ to select the hour.
3. Press the • button and the minutes start flashing. Use
the arrow buttons ▲▼ to select the minutes.
4. Press the • button and the day of week start flashing.
Use the arrow buttons ▲▼ to select the day of week.
The seven top bars indicate Monday through Sunday.
5. Press the • button to accept.
2.3 Periods with Lowering of Temperature
With DEVIreg™ 535 you have the possibility of either setting
the thermostat to keep a constant temperature, or let the
thermostat automatically switch between periods with a
lower temperature (also called economy temperature) and
periods with comfort temperature.
Using the Timer Function
In order to automatically switch between comfort tempera-
ture and economy temperature (e.g. when going to bed or
to work), the timer function is used. A status bar in the bot-
tom of the display gives an overview of timer status.
DEVIreg™ 535
8 User Guide

The day is divided into 4 time peri-
ods (see image): morning , day
, evening and night .
The start time of each period can be
configured.
The period symbol can be: Empty (thermostat is in
economy mode) or full (thermostat is in comfort
mode)
DEVIreg™ 535
User Guide 9

Default timer settings
By default, the timer has the following settings:
Floor sensor
only Room sensor only Floor and Room sensor
Temperature:
Comfort 25 °C 21 °C 21 °C
Economy 5 °C 17 °C 17 °C
Periods – Day rhythm:
Morning 06:00-08:00
Day 08:00-16:00
Evening 16:00-22:30
Night 22:30-06:00
You can use these settings as they are, or you can change
them to match your day pattern.
Return to Default Timer Settings
1. Turn off the thermostat.
2. While pressing the pinhole button,
turn on the thermostat.
The LED indicator will now flash red/
green for 1 second indicating the ther-
mostat will reset.
DEVIreg™ 535
10 User Guide

Timer Programs
Four different programs can be selected.
Program 1 Manual mode. A constant temperature is
maintained 24 hours all week.
Program 2 The temperature is lowered to economy
temperature during the day and night peri-
od all week.
P2 is a day program for e.g. working days
where the temperature is decreased during
the middle of the day and at night. In the
morning and evening, comfort temperature
is preferred.
Program 3 The temperature is lowered to economy
temperature during the night period all
week.
P3 is a program for days at home where
comfort temperature is preferred during
the day and a economy temperature at
night.
Program 4 A week program where:
Mon – Fri: Program 2 and
Sat – Sun: Program 3
P4 is a week program with Monday-Friday
as workdays and Saturday-Sunday as days
off. The 7 top bars indicate Monday
through Sunday.
DEVIreg™ 535
User Guide 11

By default, program 1 is selected.
How to define comfort periods and economy periods
Note: When defining the starting time of the 4 periods
keep in mind that the thermostat will start heating/stop
heating at the given time. Therefore some periods should
start and end before, to compensate for the time it takes to
heat up or cool down.
1. Press the clock pinhole with a small
screw driver, pencil, or needle.
The display now changes from tem-
perature to time display.
2. Keep the • button pressed for 2 sec-
onds.
The currently selected timer program
starts to flash.
3. Use ▲▼ to select the desired program and press • to
accept .
The first period bar (morning) starts flashing.
DEVIreg™ 535
12 User Guide

4. Use ▲▼ to change the start time of
this period (in increments of 15 mi-
nutes) and press • to accept .
5. Repeat Step 4 to define the start time of the day, eve-
ning and night periods.
Note: When setting the time periods you cannot go
back to the previous time period until the last one is
set. This is to ensure that the periods do not overlap.
6. Press • again and the preset comfort temperature
starts flashing.
7. Use ▲▼ to change it and press • to accept .
8. Press • again and the preset economy temperature
starts flashing.
9. Use ▲▼ to change it and press • to accept .
It can also be set to "off".
DEVIreg™ 535
User Guide 13

2.4 Minimum Floor Temperature
Note: Minimum floor temperature only applies if the ther-
mostat is configured to use a combination of room and
floor sensor.
This setting will overrule any other set point as you always
want e.g. 20°C at the floor sensor
How to set the minimum floor temperature
1. Press the clock pinhole with a small
screw driver, pencil, or needle to ac-
cess thermostat settings.
The display now changes from tem-
perature to time display.
2. Use the arrow buttons ▲▼ until you
reach the minimum floor temperature
and press the • button.
The preset minimum floor limit tem-
perature starts flashing.
--.-° means that the function is disa-
bled.
3. Use the arrow buttons ▲▼ to select the minimum
temperature.
DEVIreg™ 535
14 User Guide

4. Press the • button to accept.
The floor temperature is now kept above the specified
lower limit.
2.5 Frost Protection
How to set the thermostat in frost protection mode
1. Hold down ▼ until you reach the low-
est setting, then press ▼ again.
A frost symbol now appears and
the temperature display flashes.
2. To accept, press • or leave it flashing for 10 seconds.
How to turn off frost protection mode
1. Press ▲ (0.5sec).
DEVIreg™ 535
User Guide 15

2.6 Safety Lock
The safety lock is used for preventing undesirable changes
to the thermostat settings, i.e. all buttons will be locked un-
til the safety lock is turned off again.
How to turn the safety lock on and off
1. Press the lock pinhole with a small
screw driver, pencil, or needle.
If the safety lock was turned off, it will
now be turned on and vice versa.
When turned on, a lock symbol ap-
pears on the thermostat display.
2.7 Switching Between Floor and Room Tempera-
ture
How to display the room temperature
Note: This option only applies if the thermostat is config-
ured to use a floor sensor only.
1. Press ▲ and ▼ at the same time for 2
seconds.
The room sensor symbol is now dis-
played.
To return to the default display, press ▲ and ▼ again.
DEVIreg™ 535
16 User Guide

How to display the floor temperature
Note: This option only applies if the thermostat is config-
ured to use a combination of room and floor sensor.
1. Pressing ▲ and ▼ at the same time
for 2 seconds.
The floor sensor symbol now appears,
and the floor sensor temperature will
be displayed for 2 minutes.
2.8 Turning the Thermostat On and Off
How to turn the thermostat off
1. Hold down ▼ until you reach 5.0°.
Then press ▼ again twice.
OFF appears on the display.
2. Press • to accept.
How to turn the thermostat on
When the thermostat is off, two lines are
shown on the display.
1. Press ▲ (0.5sec).
DEVIreg™ 535
User Guide 17

3 Error Messages
Light Indications (LED)
No light The system is turned off.
Green light System is standing by, set point tem-
perature reached
Green light flash-
ing Floor sensor is defect
Red light System is heating
Switching be-
tween red and
green light
The floor temperature limit prevents
the set point room temperature from
being reached.
DEVIreg™ 535
18 User Guide

Error
code
Problem Solution
Clock
symbol
flashing
in dis-
play
Time settings
were lost due
to power cut.
The thermostat resumes to
manual mode.
E4 sym-
bol
flashing
in dis-
play
The thermo-
stat has over-
heated and
has switched
off.
Let the thermostat cool for pe-
riod. Then switch the thermo-
stat off and on. If the error per-
sists contact your authorized
installer.
E5 sym-
bol
flashing
in dis-
play
Floor sensor
short circuit-
ed.
If the error persists contact
your authorized installer.
E6 sym-
bol
flashing
in dis-
play
Floor sensor
disconnected. If the error persists contact your authorized installer.
DEVIreg™ 535
User Guide 19

4 Warranty
2
Y E A R
5 Disposal Instruction
DEVIreg™ 535
20 User Guide