DEVI DEVIreg 130 User manual

DEVIreg™ 130
Electronic Thermostat
Installation Guide
www.DEVI.com

Table of Contents
1 Introduction ............... 3
1.1 Technical Specifications ..... 4
1.2 Safety Instructions ........ 5
2Mounting Instructions ......... 6
3Settings ................. 10
3.1 Temperature Settings ...... 10
4 Warranty ................. 12
5 Disposal Instruction .......... 12
1 Introduction
DEVIreg™ 130 is an electronic thermostat to be installed di-
rectly on the wall. It is provided with a floor sensor to meas-
ure and control the desired floor temperature.
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 1 to 5 (each step corresponds
to approximately 9°C). Furthermore, the thermostat has an
LED indicator showing standby periods (green light) and
heating periods (red light).
More information on this product can also be found at:
devireg.devi.com
DEVIreg™ 130
Installation Guide 3

1.1 Technical Specifications
Operation voltage 220-240V~, 50Hz
Power consumption Max 5W
Relay:
Resistive load Max 16A / 3680W @ 230V
Inductive load cos φ= 0.3 max 1A
Sensing units NTC 15 kOhm at 25°C
Sensing values:
0°C 42 kOhm
25°C 15 kOhm
50°C 6 kOhm
Hysteresis ± 0.2°C
Ambient temperature 0 to +30°C
Frost protection temperature 5°C -
Temperature range () 5-45°C
Cable specification max 1x4mm2or 2x2,5mm2
Ball pressure temperature 75°C
Pollution degree Degree 2 (domestic use)
Type 1C
Storage temperature -20 to +65°C
DEVIreg™ 130
4 Installation Guide

IP class 30
Protection class Class II -
Dimensions 82 x 82 x 36mm
Weight 90g
The product complies with the EN/IEC Standard "Automatic
electrical controls for household and similar use":
▪EN/IEC 60730-1 (general)
▪EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
IMPORTANT: When the thermostat is used to control a
floor heating element in connection with a wooden floor or
similar material, always use a floor sensor and never set the
maximum floor temperature to more than 35°C.
Please also note the following:
▪The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
▪The thermostat must be connected to a power supply
via an all-pole disconnection switch.
DEVIreg™ 130
Installation Guide 5

▪The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
▪Always connect the thermostat to continuous power
supply.
▪Do not expose the thermostat to moisture, water, dust,
and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
Place the thermostat at a suitable height on
the wall (typically 80-170cm.).
In wet rooms, place the thermostat according
to local regulation on IP classes.
Do not place the thermostat on the inner side
of an exterior wall.
DEVIreg™ 130
6 Installation Guide

▪Place the floor sensor in a conduit in an
appropriate place where it is not exposed
to sunlight or draft from door openings.
▪Equally distant and >2cm from two heat-
ing cables.
▪The conduit should be flush with the floor
surface - countersink the conduit if neces-
sary.
▪Route the conduit to the connection box.
▪The bending radius of the conduit must
be min 50mm.
DEVIreg™ 130
Installation Guide 7

Follow the steps below to mount the thermostat:
1. Open the thermostat:
▪Lift off the button using a small screwdriver.
▪Loosen the screw which holds the front.
▪Push down the release tab at the top of the thermo-
stat using a flat object while slowly pulling off the
front cover.
DEVIreg™ 130
8 Installation Guide

2. Fasten the thermostat directly to the wall by driving
the screws through the holes in each side of the ther-
mostat.
= Screw holes for fastening the thermostat.
3. Connect the thermostat according to the connection
diagram.
IP30
0T30
D130
NTC
LN
1234
Sensor
Max.Load
16 (1) A
Mains
220-240V~
N
LOAD
L
LOAD
The screen of the heating cable must be connected to
the earth conductor of the power supply cable by us-
ing a separate connector.
Note: Always install the floor sensor in a conduit in the
floor.
DEVIreg™ 130
Installation Guide 9

4. Install the front cover and button in the reverse order
of disassembly.
5. Turn on the power supply.
3 Settings
3.1 Temperature Settings
How to change the minimum and maximum floor tem-
peratures
1. Lift off the adjustment
button using a thin
screwdriver. (1)
2. Move the pins to the
desired positions. (2
and 3)
3. Put the adjustment
button back in place.
Please be aware of the following:
▪The floor temperature is measured where the sensor is
placed.
▪The temperature of the bottom of a wooden floor can
be up to 10 degrees higher than the top.
DEVIreg™ 130
10 Installation Guide

▪Floor manufactures often specify the max temperature
on the top surface of the floor (usually 27-28˚C).
▪By default, the maximum floor temperature is set to
35°C.
▪Always use a floor sensor or a room + floor sensor
combination to control floor heating. Without a floor
sensor, the temperature control may be less accurate
and you risk overheating the floor.
Thermal
resist-
ance
[m2K/W]
Examples of floor-
ing
Details Approximate
setting for
25˚C floor
temperature
0.05 8 mm HDF based
laminate > 800 kg/m328˚C
0.10 14 mm beech par-
quet
650 - 800
kg/m3
31˚C
0.13 22 mm solid oak
plank > 800 kg/m332˚C
< 0.17 Max. carpet thick-
ness suitable for
floor heating
acc. to EN
1307
34˚C
0.18 22 mm solid fir
planks
450 - 650
kg/m3
35°C
DEVIreg™ 130
Installation Guide 11

4 Warranty
2
Y E A R
5 Disposal Instruction
DEVIreg™ 130
12 Installation Guide

DEVIreg™ 130
Installation Guide 13

DEVIreg™ 130
14 Installation Guide

DEVIreg™ 130
Danfoss A/S
Electric Heating Systems
Ulvehavevej 61
7100 Vejle
Denmark
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.DEVI.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its
products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes
being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. DEVI and the DEVI logo-
type are trademarks of Danfoss A/S. All rights reserved.
08095775 & VICKD202 Produced by Danfoss © 06/2012

DEVIreg 130
140F1010
220-240V~ 50-60Hz~ +5 to +45°C 16A/3680W@230V~ IP 30
Product Documentation
DK EL 7224215001 SE EL XXXXXX NO EL 5402690 FI SSTL 3531130
Designed in Denmark for Danfoss A/S
5 7 0 3 4 6 6 2 0 8 9 5 3