DeVilbiss FinishLine HAR-680 Reference manual

SB-6-224-A (11/2016) 1 / 2
SERVICE BULLETIN
HAR-680 80 CFM FILTER + REGULATOR
DESCRIPTION
These units are designed to remove
water and dirt particles.
SPECIFICATIONS:
Air Inlet: 1/2 NPT (female)
Air Outlet HAF-580: 3/8 NPT (female)
Air Outlet HAR-680: 1/4 NPSM (male)
Air Capacity: 80 CFM filter
50 CFM regulator
Max. Pressure: 150 PSI
Max. Temp.: 150° F
Filter Size: 5 micron
Risk of personal injury.
Risk of property damage.
RELEASE ALL AIR PRESSURE
BEFORE SERVICING.
This product is specifically designed
for compressed air service. Use with
any other fluid (liquid or gas) is a
misapplication. For example, use
with or injection of certain hazard-
ous gases in the system (such as
oxygen or liquid petroleum gas)
could be harmful to the unit or
result in a combustible condition
that may cause fire or explosion.
Manufacturer’s warranties are void
in the event of misapplication and
manufacturer assumes no responsi-
bility for any resulting loss.
INSTALLATION
1.Assemble unit (refer to Figure1).
2.Install with the air flowing into the
top of the filter.
3.Install in a vertical position.
OPERATION
1.Turn the regulator’s handle clock-
wise to increase pressure.
2.To decrease pressure, turn the
handle counterclockwise.
3.Relieve downstream pressure by
triggering spray gun or tool.
MAINTENANCE
1.Drain filter daily.
2.Depressurize before replacing
filter element.
3.Replace element at least once per
year.
SERVICE PARTS
See Parts List, page 2.
WARRANTY
This product is covered by DeVil-
biss’ one year limited warranty. See
SB-1-000 which is available upon
request.
FIGURE 1
Only on
HAR-680

SB-6-224-A (11/2016)2 / 2
USA/Canada
www.autorenishdevilbiss.com
[email protected]
Toll Free Tel: [phone]
Toll Free Fax: [phone]
Mexico
www.autorenishdevilbiss.com.mx
Toll Free Tel: [phone] USA
DeVilbiss Automotive Renishing is part of Carlisle Fluid Technologies, a global leader in
innovative nishing technologies. For technical assistance or to locate an authorized distributor,
contact one of our international sales and customer support locations.
WARRANTY POLICY
DeVilbiss products are covered by Carlisle Fluid Technologies one year materials and workmanship limited warranty. The use of any parts
or accessories, from a source other than Carlisle Fluid Technologies, will void all warranties. For specic warranty information please
contact the closest Carlisle Fluid Technologies location listed below.
Carlisle Fluid Technologies reserves the right to modify equipment specications without prior notice.
DeVilbiss®, Ransburg®, MS®, BGK®, Binks®, TEKNA®, FinishLine®, StartingLine®, CamAir®, CVi®, PLUS®, GTi®, and PRi® are registered trademarks of Carlisle Fluid Technologies, Inc.
©2016 Carlisle Fluid Technologies, Inc. All rights reserved.
12
3
4
1
7
5
6
8
8
4
PARTS LIST
Ref. Individual
No. Order No. Part No. Description Parts Req.
1 130100 HAR-520 Regulator 1
2 240160 VA-594 Shut-Off Valve 1
3 192314 GA-375 Pressure Gauge 1
4 — — 80 CFM Filter Unit 1
5 803641 HAF-47 80 CFM Filter Element 1
6 **Socket Head Screw, 4
1/4-20 x 3/4
7 **Wingnut, 1/4-20 1
8 802112 KK-5088 Regulator Kit 1
*Purchase Locally
FIGURE 2