DeZurik APCO CVS-EDV User manual

DeZURIK, Inc. Sartell, Minnesota USA | Phone: [phone] | www.dezurik.com | [e-mail]
APCO CVS-EDV
SWING CHECK VALVES
Instruction
D12042
February 2016

DeZURIK
Instruction and Operating Manual Page 2 © 2022 DeZURIK, Inc.
Instructions
These instructions are for use by personnel who are responsible for the installation, operation and
maintenance of DeZURIK valves, actuators or accessories.
Safety Messages
All safety messages in the instructions are identified by a general warning sign and the signal word CAUTION,
WARNING or DANGER. These messages indicate procedures to avoid injury or death.
Safety label(s) on the product indicate hazards that can cause injury or death. If a safety label becomes difficult
to see or read, or if a label has been removed, please contact DeZURIK for replacement label(s).
Personnel involved in the installation or maintenance of valves should be constantly alert to potential
emission of pipeline material and take appropriate safety precautions. Always wear suitable protection
when dealing with hazardous pipeline materials. Handle valves which have been removed from service
with suitable protection for any potential pipeline material in the valve.
Inspection
Your DeZURIK product has been packaged to provide protection during shipment; however, items can be
damaged in transport. Carefully inspect the unit for damage upon arrival and file a claim with the carrier if
damage is apparent.
Parts
Replaceable wear parts are listed on the assembly drawing. These parts can be stocked to minimize
downtime. Order parts from your local DeZURIK sales representative or directly from DeZURIK. When ordering
parts please provide the following information:
If the valve has a data plate: please include the 7-digit part number with either 4-digit revision number
(example: 9999999R000) or 8-digit serial number (example: S1900001) whichever is applicable. The
data plate will be attached to the valve assembly. Also, include the part name, the assembly drawing
number, the balloon number and the quantity stated on the assembly drawing.
If there isn't any data plate visible on the valve: please include valve model number, part name, and
item number from the assembly drawing. You may contact your local DeZURIK Representative to help
you identify your valve.
DeZURIK Service
DeZURIK service personnel are available to maintain and repair all DeZURIK products. DeZURIK also offers
customized training programs and consultation services. For more information, contact your local DeZURIK
sales representative or visit our website at DeZURIK.com.

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 3 D12042
Table of Contents
Description.................................................................................................................................4
Handling and Storage.................................................................................................................4
Installation..................................................................................................................................4
Fusion/Powder Coated Valves...................................................................................................5
Maintenance...............................................................................................................................5
Shaft Packing Adjustment.......................................................................................................5
Shaft Packing Replacement ...................................................................................................6
Disc Seat Replacement..........................................................................................................6
Changing Counterweight or Spring Assembly to Opposite Side of Valve...............................7
Adding Air Cushion Assembly to Valve...................................................................................8
Operation ...................................................................................................................................9
Closure Speed Control Adjustment (Valves with Lever & Weight)..........................................9
Closure Speed Control Adjustment (Valves with Air Cushion)................................................9
Start-up Procedure .................................................................................................................9
Adjustment (Valves with Air Cushion with Lever & Weight)..................................................10
Adjustment (Valves with Lever & Weight).............................................................................10
Drawings..................................................................................................................................11
CVS-EDV Swing Check Valve..............................................................................................11
Lever & Weight.....................................................................................................................12
Air Cushion...........................................................................................................................13
Lever & Spring 3-14" ............................................................................................................14
Lever & Spring 16-30" ..........................................................................................................15
Bill of Materials Table ...........................................................................................................16
Troubleshooting .......................................................................................................................17

DeZURIK
APCO CVS-EDV Swing Check Valves
D12042 Page 4 February 2016
Description
A swing check valve consists of a valve body, a cover, and a disc that is connected to a hinge. The disc
swings away from the valve-seat to allow flow in the forward direction, and returns to valve-seat when
upstream flow is stopped, to prevent backflow. The valve is equipped with either a lever & weight, an air
cushion with lever & weight, or a lever & spring to assist with closing the valve.
Handling and Storage
Lifting the valve improperly may damage it. Do not fasten lifting devices to the actuator or through the
seat opening in the body. Lift the valve with slings, chains or cables fastened around the valve body, or
fastened to bolts or rods through bolt holes in the flanges.
If installation will be delayed, place valve indoors in secure, weather tight storage. If temporary outside
storage is unavoidable, make sure a vermin proof rain cover (water shedding tarp, etc.) is secured
around/over the equipment to keep off rain and mud. Skid and set the assembly on a flat, solid, and
well drained surface for protection from ground moisture, runoff and pooled rain water.
Installation
•The APCO CVS-EDV Swing Check Valve may be installed in a horizontal or vertical position
(with the flow upward). In either case, the Counterweight Arm should be set in horizontal
position. Unless otherwise specified, the valves are shipped for horizontal installation.
oSee Figure 3 and 4 for component identification. On Lever and weight valves, to change
the counterweight arm position from horizontal to vertical installation, unscrew Lever Arm
to Shaft Set Screw (B57), remove Counterweight Lever Arm Washer (B56), loosen the
Lever Weight Assembly Set Screw (B55), slide the counterweight arm assembly off the
Shaft (A13), rotate the counterweight arm assembly and slide it back onto the Shaft
(A13) using the appropriate keyway shown in Figure 1.
Figure 1 – Counterweight Arm Position

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 5 D12042
Installation (Continued)
•Before installation, remove foreign material such as weld spatter, oil, grease, and dirt from the
pipeline.
•Prepare pipe ends and install valves in accordance with the pipe manufacturer’s instructions for
the joint used.
Do not deflect the pipe-valve joint. Minimize bending stresses in the valve end
connection with pipe loading.
If excessive seat leakage occurs during start-up, recheck the installation and
eliminate any distortion to the valve body.
•Ensure the valve and pipeline flanges are concentric to ensure proper flange sealing and seat
leakage control.
•Tighten the flange bolts or studs in a crisscross pattern a minimum of four stages.
Fusion/Powder Coated Valves
Valves with fusion/powder coated exterior paint require flat washers to be installed
under the flange nuts when installing the valve to the pipeline flange to prevent the
paint from cracking or chipping.
Maintenance
It is suggested that these valves, which do not require routine scheduled maintenance, be included as
part of the normal facility equipment inspections for any malfunction while under normal usage
conditions.
Shaft Packing Adjustment
Packing adjustment may be needed to optimize packing life on initial start-up.
These valves may open or close, swinging the counterweight/spring lever arm without
warning due to flow changes from pumps starting and stopping. Servicing or working
around these valves while the pipeline is under pressure can cause personal injury or
equipment damage.
Workers must be cautious when working around these valves. Relieve pipeline pressure
and lockout the pumps before servicing the valve.
Tighten the Gland Nuts (A26) (see Figure 3) evenly only until the packing leak stops.
Caution: Do not over-tighten Packing Gland. Valve can remain open during operation if packing is too
tight. After packing adjustments are made and pipeline is pressurized, visually inspect valve stroke to
ensure proper operation.
Note: Do not continue tightening after leak stops. If packing leak cannot be stopped by tightening the
gland nuts, the packing must be replaced.

DeZURIK
APCO CVS-EDV Swing Check Valves
D12042 Page 6 February 2016
Maintenance (Continued)
Shaft Packing Replacement
Removal of the valve from the line for shaft packing replacement is not required as long as the shaft is
accessible.
1. Relieve the pressure in the pipeline and close the valve.
2. If needed, remove Counterweight Lever Arm Fabrication (B54), spring Lever Arm Fabrication
(B33 or B85) or Cushion Lever (B88). Then, remove the Gland Nuts (A26) and Gland (A25)
from Shaft (A13).
3. Remove Long Flat Key (B78) from extended shaft.
4. Remove the V-Type Packing Sets (A23) with a flexible packing hook or similar tool. Clean the
packing area, being careful not to damage it.
5. Obtain the proper size packing from the parts list. Cut the packing rings to fit around the shaft.
Install one ring at a time. Make sure it is clean and has not picked up any dirt in handling before
installing it. Lubricate I.D. of each packing ring. Each ring should be firmly seated with a tamping
tool. Do not depend on the packing gland entirely to seat the set of rings properly. This practice
will jam the last rings installed but leave the first ones loose in the box.
6. See “Shaft Packing Adjustment” section to adjust packing after replacing.
Disc Seat Replacement
Servicing the valve while the pipeline is under pressure can cause personal injury or
equipment damage. Relieve pipeline pressure before servicing the valve.
1. Relieve the pressure in the pipeline and close the valve.
2. Remove Seat Retaining Ring (A16) from Disc (A10).
3. Remove old Disc Seat (A15) and replace with new Disc Seat.
4. Re-install Seat Retaining Ring (A16).

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 7 D12042
Maintenance (Continued)
Changing Counterweight or Spring Assembly to Opposite Side of Valve
Servicing the valve while the pipeline is under pressure can cause personal injury or
equipment damage. Relieve pipeline pressure before servicing the valve.
1. Relieve the pressure in the pipeline and close the valve.
2. Unscrew Lever Arm to Shaft Set Screw (B57). Remove Counterweight Lever Arm Washer
(B56). Loosen the Lever Weight Assy Set Screw (B55) and remove the counterweight
assembly, or loosen Spring Lever Arm Retention Screw (B31 or B87) and remove spring
assembly with Spring Bracket (B32) or Spring Cylinder (B83). (Note that a special spring
bracket or cylinder may be required to change lever & spring assembly to opposite side of
valve.)
3. If the valve is equipped with an Pneumatic Cylinder (B68):
a. Remove the Cushion Lever Clevis Pin Retaining Ring (B62) and Cushion Lever Clevis
Pin (B61) from the Y-Connector (B63) eye.
b. Remove the Pneumatic Cylinder assembly (B68) and Cylinder Bracket (B66) from the
Body (A1).
c. Loosen AC Assy Set Screw (B76) and remove the Cushion Lever (B88) from the Shaft
(A13).
4. Remove Long Flat Key (B78).
5. Loosen and remove Cover Nuts (A28) and Cover Nut Washers (A29). Remove Cover (A2).
6. Loosen and remove Limit Screw (A11).
7. From the extended shaft side of the valve, loosen and remove Gland Nuts (A26), remove the
Gland (A25), V-Type Packing set (A23) and Filler Ring (A21) from the Body (A1). Repeat
process on side opposite extended shaft.
8. Remove the Shaft (A13) along with Key (A8) from the Body (A1).
9. Flip and insert Shaft (A13) along with Key (A8) positioned in slot into shaft opening on opposite
side of Body (A1). Key must align with slot in Disc Arm (A9).
10. Install Filler Ring (A21) over extended Shaft (A13) flush into Body (A1) recess. Install V-Type
Packing (A23) pieces one at a time with flat face of first piece flush against Filler Ring (A21).
Follow insertion of the first 3 packing pieces with cap piece of the V-Type Packing set. Make
sure all pieces are clean and have not picked up any dirt in handling before installing it.
Lubricate I.D. of each piece. Each piece should be firmly seated with a tamping tool. Install the
Gland (A25), and Gland Nuts (A26) loosely. Repeat process on opposite side of valve.
11. Install Limit Screw (A11) in Body (A1) hole above receiving notch in Shaft (A13). Adjust V-Type
Packing Sets (A23) and tighten Gland Nuts (A26) on both sides.
12. Install the Cover (A2) to the Body (A1) with Cover Nuts (A28) and Cover Nut Washers (A29).
13. Insert Long Flat Key (B78) into slot at end of Shaft (A13).

DeZURIK
APCO CVS-EDV Swing Check Valves
D12042 Page 8 February 2016
14. If the valve is equipped with an Pneumatic Cylinder (B68):
a. Install the Cushion Lever (B88) onto the Shaft (A13).
b. Install the Pneumatic Cylinder assembly (B68) and Cylinder Bracket (B66) onto the
Body (A1) using Cylinder Bracket Mounting Bolts (B69).
c. Slide Cushion Lever (B88) into Y-Connector (B63). Install the Cushion Lever Clevis Pin
(B61) into the Y-Connector (B63) eye. Secure with Cushion Lever Clevis Pin Retaining
Ring (B62). Tighten AC Assy Set Screw (B76).
15. Install counterweight assembly by sliding Counterweight Lever Arm Fabrication (B54) onto Shaft
(A13) and tightening Lever Weight Assy Set Screw (B55), or install spring lever assembly by
sliding Lever Arm Fabrication (B33 or B85) onto the Shaft (A13) and tightening Spring Lever
Arm Ret. Screw 3-14” (B31) or Spring Lever Arm Ret. Screw 16-30” (B87). On sizes 3-14”,
install Spring Bracket (B32) to Body (A1). On sizes 16-30”, install Spring Cylinder (B83) to Body
(A1). Secure using Spring Bracket Screws (B38) or Spring Cylinder Mount Bolts (B84). On size
3-14”, hook ends of Spring (B34) thru Eye Bolt (B35) and Lever Arm Fabrication 3-14” (B33).
16. Position Counterweight Lever Arm Washer (B56) at end of Shaft (A13). Insert Lever Arm to
Shaft Set Screw (B57) and tighten.
Adding Air Cushion Assembly to Valve
Servicing the valve while the pipeline is under pressure can cause personal injury or
equipment damage. Relieve pipeline pressure before servicing the valve.
1. Relieve the pressure in the pipeline and close the valve.
2. Unscrew Lever Arm to Shaft Set Screw (B57). Remove Counterweight Lever Arm Washer
(B56). Loosen the Lever Weight Assy Set Screw (B55) and remove the counterweight
assembly.
3. Install the Cushion Lever (B88) onto the Shaft (A13).
4. Install the Pneumatic Cylinder assembly (B68) and Cylinder Bracket (B66) onto the Body (A1)
using Cylinder Bracket Mounting Bolts (B69).
5. Slide Cushion Lever (B88) into Y-Connector (B63). Install the Cushion Lever Clevis Pin (B61)
into the Y-Connector (B63) eye. Secure with Cushion Lever Clevis Pin Retaining Ring (B62).
Tighten AC Assy Set Screw (B76).
6. Install counterweight assembly by sliding Counterweight Lever Arm Fabrication (B54) onto Shaft
(A13) and tightening Lever Weight Assy Set Screw (B55).

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 9 D12042
Operation
The flow from the pump opens the Disc (A10) and raises the counterweight assembly. If the valve is
equipped with an air cushion, the cylinder piston is pulled upward, drawing air freely into the Pneumatic
Cylinder (B68) through the Flow Control Valve (B67).If the 3-14” valve is equipped with a lever &
spring, the spring (B34) is extended by the Lever Arm Fabrication (B33) raising up. If the 16-30” valve is
equipped with a lever & spring, the spring (B86) is compressed by the Lever Arm Fabrication (B85)
raising up, lifting the Spring Shaft (B39), which in turn pulls the Spring Tension Plate (B79) which the
Spring (B86) is seated on.
When the pump is shut off, the decreased flow allows gravity to close the Disc (A10) towards the Body
Seat Ring (A5). For valves equipped with a lever & weight, the Counterweight (B60) causes the Disc
(A10) to close faster or slower depending on its position along the Counterweight Arm (B59). For valves
equipped with an air cushion, the closure speed can be dampened by the Pneumatic Cylinder (B68).
As the Disc (A10) closes, the cylinder piston is pushed downwards and the compressed air can only
escape through the Flow Control Valve (B67) on the bottom of the cylinder. The exhausting air can be
adjusted with the Flow Control Valve (B67) to suit the best performance for the installation. For 3-14”
valves equipped with a lever & spring, the stored energy in the extended spring (B34) causes the Disc
(A10) to close in addition to weight of the disc. For 16-30” valves equipped with a lever & spring, the
stored energy in the compressed spring (B86) causes the Disc (A10) to close in addition to weight of
the disc.
System static pressure (downstream of the swing check valve) keeps the Disc (A10) and Disc Seat
(A15) closed and seated against the Body Seat Ring (A5).
Closure Speed Control Adjustment (Valves with Lever & Weight)
•Faster Disc closing - Move Counterweight (B60) away from the Shaft (A13).
•Slower Disc closing – Move Counterweight (B60) towards Shaft (A13).
Closure Speed Control Adjustment (Valves with Air Cushion)
•Increase cushioning - Turn adjusting screw of Flow Control Valve (B67) clockwise.
•Decrease cushioning - Turn adjusting screw of Flow Control Valve (B67) counterclockwise.
Start-up Procedure
1. Ensure the Counterweight Arm (B59) is horizontal.
2. Throttle down mainline isolation valve (furnished by others) on discharge side of Swing Check
Valve to approximately 1/3 open to prevent severe slamming during initial pump shutdown
testing.
3. Position Counterweight (B60) midway on the lever and lock in place.
4. If valve has an Air Cushion: Unlock Flow Control Valve by turning Flow Control Valve lock nut
counter-clockwise. Turn Flow Control Valve adjustment screw two (2) turns counterclockwise
from fully close position. Lock Flow Control Valve by turning Flow Control Valve lock nut
clockwise. (See Figure 2.)
5. Start and stop pump and observe rate of closing.

DeZURIK
APCO CVS-EDV Swing Check Valves
D12042 Page 10 February 2016
Operation (Continued)
Figure 2 – Adjustable Flow Control Valve
Adjustment (Valves with Air Cushion with Lever & Weight)
Condition Adjustment
Check valve slams
Unlock Flow Control Valve by turning valve lock nut counter-clockwise. Turn
adjustment screw of Flow Control Valve one-half (1/2) turn clockwise. Repeat
start and stop. If slam persists, continue turning adjustment screw in ½ turn
increments. Be careful not to fully close Flow Control Valve. Lock Flow Control
Valve when finished.
Slam persists Move weight towards end of lever a couple of inches. Repeat start and stop.
Slam still persists
Continue repeating above steps until satisfactory closing is achieved. Then
increase opening discharge isolation valve to ½ open.
Repeat start and stop
pump sequence and above steps until isolation valve is full open.
Lock Flow
Control Valve when finished.
Adjustment (Valves with Lever & Weight)
Condition Adjustment
Check valve slams Move weight towards end of lever a couple of inches. Repeat start and stop.
Slam persist Repeat above step.
Notes:
1. Testing must be conducted carefully and adjustments made in small increments to arrive at the
optimum setting where the swing check valve shuts off just prior to or at zero reverse flow.
2. The APCO CVS-EDV Swing Check Valve is not a silent closing check valve.

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 11 D12042
Drawings
Figure 3 – APCO CVS-EDV Swing Check Valve

DeZURIK
APCO CVS-EDV Swing Check Valves
D12042 Page 12 February 2016
Drawings (Continued)
Figure 4 - CVS-EDV Swing Check Valve (Lever & Weight)

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 13 D12042
Drawings (Continued)
Figure 5 - CVS-EDV Swing Check Valve (Air Cushion)

DeZURIK
APCO CVS-EDV Swing Check Valves
D12042 Page 14 February 2016
Drawings (Continued)
Figure 6 - CVS-EDV Swing Check Valve (Lever & Spring 3-14”)

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 15 D12042
Drawings (Continued)
Figure 7 - CVS-EDV Swing Check Valve (Lever & Spring 16-30”)

DeZURIK
APCO CVS-EDV Swing Check Valves
D12042 Page 16 February 2016
Table 1 - CVS-EDV Swing Check Valve Parts
Lever & Weight, Lever & Spring, and Cylinder Parts
Item
Number
Description
Item
Number
Description
A1 Body B31 Spring Lever Arm Ret. Screw 3-14"
A2 Cover B32 Spring Bracket
A3 Cover Gasket B33 Lever Arm Fabrication 3-14"
A5 Body Seat Ring B34 Spring 3-14"
A6 Seat O-Ring B35 Eye Bolt
A8 Key B36 Eye Bolt Washer
A9 Disc Arm B37 Eye Bolt Retaining Nut
A10 Disc B38 Spring Bracket Screw
A11 Limit Screw B39 Spring Shaft
A13 Shaft B40 Spring Shaft Nut
A14 Body Seat Screw B41 Spring Cylinder Pin
A15 Disc Seat B42 Spring Cylinder Pin Retaining Ring
A16 Seat Retaining Ring B54 Counterweight Lever Arm Fabrication
A17 Disc Seat Screw B55 Lever Weight Assy Set Screw
A18 Disc Stem B56 Lever Arm Washer
A19 Disc Nut B57 Lever Arm To Shaft Set Screw
A20 Disc Washer B58 Lever Arm Set Screw Nut
A21 Filler Ring B59 Counterweight Arm
A23 V-Type Packing B60 Counterweight
A25 Gland B61 Cushion Lever Clevis Pin
A26 Gland Nut B62 Cushion Lever Clevis Pin Retaining Ring
A27 Gland Stud B63 Y-Connector
A28 Cover Nut B65 Counterweight Set Screw
A29 Cover Nut Washer B66 Cylinder Bracket
A30 Cover Stud B67 Flow Control Valve
A31 Data Plate B68 Pneumatic Cylinder
A32 Drive Screws B69 Cylinder Bracket Mounting Bolt
A42 Plug B70 Clevis Pin
A64 Cover Eye Bolt B71 Clevis Pin Retaining Ring
B72 Female Clevis Bracket
B73 Bracket Shim
B74 Male Clevis Bracket
B75 Eye Bracket Mounting Bolt
B76 AC Assy Set Screw
B77 Lever Arm Set Screw
B78 Long Flat Key
B79 Spring Tension Plate
B80 Y-Connection

DeZURIK
APCO CVS-EDV Swing Check Valves
February 2016 Page 17 D12042
Table 1 - Continued
Lever & Weight, Lever & Spring, and Cylinder Parts
Item
Number
Description
B81 Y-Connector Pin
B82 Y-Connector Pin Retaining Ring
B83 Spring Cylinder
B84 Spring Cylinder Mount Bolt
B85 Lever arm fabrication 16-30"
B86 Spring 16-30"
B87 Spring Lever Arm Ret. Screw 16-30"
B88 Cushion Lever
Troubleshooting
Condition Possible Cause Corrective Action
Shaft seal leaks. Packing is loose. Tighten gland nuts only until the
leak stops.
Packing is worn. Replace Packing.
Valve leaks excessively from
one side of the disc to the other.
Foreign matter caught between
disc and seat. Fully open valve to remove object.
Disc seat is worn or damaged. Repair disc seat or replace
valve.
Valve leaks at flange joint.
Loose flange bolting. Tighten flange bolting.
Blown flange gasket. Replace flange gasket.
Misalignment or damage to field
piping and supports. Adjust misalignment or repair piping or supports.
Damaged flange face/s or
improper flange connections.
Repair flange, replace valve
body or adjust flange
connections.
Valve does not fully close.
Object is wedged between seat
and disc. Fully open valve to remove object.
Packing Gland is too tight Loosen packing gland fasteners. Packing may need to be
replaced if leakage occurs.

Limited Warranty
DeZURIK, Inc. (“Seller”) manufactured products, auxiliaries and parts for a period of twenty-four (24) months from date of shipment from
Seller’s factory, are warranted to the original purchaser onlyagainst defective workmanship and material, but only if properly stored, installed,
operated, and serviced in accordance with Seller’s recommendations and instructions.
For items proven to be defective within the warranty period, your exclusive remedy under this limited warranty is repair or replacement of
the defective item, at Seller’s option, FCA Incoterms 2020 Seller’s facility with removal, transportation, and installation at your cost.
Products or parts manufactured by others but furnished by Seller are not covered by this limited warranty. Seller will provide repair or
replacement for other’s products or parts only to the extent provided in and honored by the original manufacturer’s warranty to Seller, in
each case subject to the limitations contained in the original manufacturer’s warranty.
No claim for transportation, labor, or special or consequential damages or any other loss, cost or damage is being provided in this limited
warranty. You shall be solely responsible for determining suitability for use and in no event shall Seller be liable in this respect.
This limited warranty does not warrant that any Seller product or part is resistant to corrosion, erosion, abrasion or other sources of failure,
nor does Seller warrant a minimum length of service.
Your failure to give written notice to us of any alleged defect under this warranty within twenty (20) days of its discovery, or attempts by
someone other than Seller or its authorized representatives to remedy the alleged defects therein, or failure to return product or parts for
repair or replacement as herein provided, or failure to store, install, or operate said products and parts according to the recommendations
and instructions furnished by Seller shall be a waiver by you of all rights under this limited warranty.
This limited warranty is voided by any misuse, modification, abuse or alteration of Seller’s product, accident, fire, flood or other Act of God,
or your failure to pay entire contract price when due.
The foregoing limited warranty shall be null and void if, after shipment from our factory, the item is modified in any way or a component of
another manufacturer, such as but not limited to, an actuator is attached to the item by anyone other than a Seller factory authorized service
personnel.
All orders accepted shall be deemed accepted subject to this limited warranty, which shall be exclusive of any other or previous Warranty,
and this shall be the only effective guarantee or warranty binding on Seller, despite anything to the contrary contained in the purchase order
or represented by any agent or employee of Seller in writing or otherwise, notwithstanding, including but not limited to implied warranties.
THE FOREGOING REPAIR AND REPLACEMENT LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS AND
LIABILITIES, INCLUDING ALL WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR OF MERCHANTABILITY OR
OTHERWISE, EXPRESSED OR IMPLIED IN FACT OR BY LAW, AND STATE SELLER’S ENTIRE AND EXCLUSIVE LIABILITY AND YOUR
EXCLUSIVE REMEDY FOR ANY CLAIM IN CONNECTION WITH THE SALE AND FURNISHING OF SERVICES, GOODS OR PARTS,
THEIR DESIGN, SUITABILITY FOR USE, INSTALLATION OR OPERATIONS.
Disclaimer
Metric fasteners should not be used with ASME Class 150/300 bolt holes and flange bolt patterns. If you use metric fasteners with ASME
Class 150/300 bolt holes and flange bolt patterns, it may lead to product failure, injury, and loss of life. DeZURIK Inc. disclaims all liability
associated with the use of metric fasteners with ASME Class 150/300 bolt holes and flange patterns, including but not limited to personal
injury, loss of life, loss of product, production time, equipment, property damage, lost profits, consequential damages of any kind and
environment damage and/or cleanup. Use of metric fasteners with ASME Class 150/300 bolt holes and flange bolt patterns is a misuse that
voids all warranties and contractual assurances. If you use metric fasteners with ASME Class 150/300 bolt holes and flange bolt patterns,
you do so at your sole risk and any liability associated with such use shall not be the responsibility of DeZURIK, Inc. In addition to the
foregoing, DeZURIK’s Manufacturer’s Conditions apply.
Limitation of Liability
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES
WHATSOEVER, AND SELLER’S LIABILITY, UNDER NO CIRCUMSTANCES, WILL EXCEED THE CONTRACT PRICE FOR THE GOODS
AND/OR SERVICES FOR WHICH LIABILITY IS CLAIMED. ANY ACTION FOR BREACH OF CONTRACT BY YOU, OTHER THAN RIGHTS
RESPECTING OUR LIMITED WARRANTY DESCRIBED ABOVE, MUST BE COMMENCED WITHIN 12 MONTHS AFTER THE DATE OF
SALE. Sales and Service
For information about our worldwide locations, approvals, certifications and local representative:
Web site: www.dezurik.com E-Mail: [email protected]
250 Riverside Ave. N., Sartell, MN 56377 ● Phone: [phone] ● Fax: [phone]
DeZURIK, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation.
Design features, materials of construction and dimensional data, as described in this manual, are provided for your information only
and should not be relied upon unless confirmed in writing by DeZURIK, Inc. Certified drawings are available upon request.
Printed in U.S.A.
October 2021