Diamond IDS40-R6 User manual

Mod: IDS40-R6
Production code: 801054_200
06/2021

QUICK START GUIDE
VERY IMPORTANT: Always read the safety and operations instructions before starting up
the appliance to obtain full safety and operating instructions.
Operation of the equipament is totally controlled by a digital DIXEL thermostat, which allows for
selection of temperature.
Connect the equipment to the mains. If “OFF” appears in the digital display, press ON/OFF key.
It is necessary to wait +/- 2 minutes for the compressor to star after the cabinet is connected to the
mains.
Digital controls the temperature from -2ºC to +8ºC on SNACK models (ID 40-R6), 0ºC to +5ºC
(IDS40-R6) on FISH models and negative models (IE40-R2) from -15ºC to -22ºC with factory set
point -18ºC.
To change the set point, you shall do the steps described bellow:
To do this press SET key more than 2 seconds to change the set point value;
The value of set point will be displayed and the “ºC” will star blinking;
To change the Set value push UP or DOWN arrows within 10 seconds;
To record the new set point value, push the SET key again or wait for 10 seconds
ALARM SIGNALS
Message
Cause
“P1”
Room probe failure
“P2”
Evaporator probe failure
“P3”
Third probe failure
“HÁ”
Maximum temperature alarm
“LA”
Minimum temperature alarm
“dA”
Door open
“EA”
External alarm
“CA”
Serious external alarm (i2F=bAL)
“CA”
Pressure switch alarm (i2F= PAL)
“rtc”
Real time clock alarm
rtF
Real time clock boar failure
Defrosting is automatic and controlled by the thermostat, the water from the process is drained
through a hole into a container. This container must be empty
regulary, -/+ twice a week.
When is possible connect to the sewers with a siphon where
the equipment is installed.
Very Important: This recipient (water tray) is supplied
inside the cabinet. The user must introduce it on the
guides below the cabinet, and make sure the sewage pipe
send the water to inside the water tray. See the scheme:
UP
DOWN// +3 seg Defrost ON
SET
ON/ OFF
EN
SET1=SET 2
Not USED

Table of Parameters
DIXELL XR60CH c/ prog. XR 70 CH
DC-09.151-PRD
R02/22.04.2021
Parameters
Code
Range
ASP 400 Snack
ASP 400 FISH
ASP 400 N
LT
NT
NT
LT
LT
Set Point
SEt
LS; US
2
2
2
2
-20
Differential
HY
(0.1 to 25,5ºC)
3
3
3
3
4
Minimum set point
LS
(-100 to SET)
-2
0
0
-2
-22
Maximum set point
US
(Set to 150ºC)
+8
+5
+5
+8
-15
Thermostat probe calibration
ot
(-12,0 to 12,0º)
-1
-1
-1
-1
+1
Evaporator Probe presence
P2P
N;Y
Y
Y
Y
Y
Y
Evaporator probe calibration
oE
(-12,0 to 12,0)
0
0
0
0
0
Third probe presence
P3P
N; Y
n
n
n
n
n
Third probe calibration
o3
(-12,0 to
12,0ºC)
0.0
0.0
0.0
0.0
0.0
Second digital input presence
P4C
Pb, id2
Id2
Id2
Id2
Id2
Id2
Outputs delay at start up
odS
0 to 255 min
2
2
2
2
2
Anti-short cycle delay
AC
0 to 50 min
3
3
3
3
4
Anti-short cycle delay for second
compressor
AC1
0 to 50 min
0
0
0
0
0
Continuous cycle duration
CCt
0.0 to 24h00
min, res.10 min
0.0
0.0
0.0
0.0
0.0
Set point continuous cycle
CCS
(-100 to
150,0ºC)
+2
+2
+2
+2
-22
Compressor ON time with faulty probe
Con
0 to 255 min
10
20
20
10
20
Compressor OFF time with faulty probe
CoF
0 to 255 min
20
20
20
20
5
Temperature measurement unit
CF
ºC; ºF
ºC
ºC
ºC
ºC
ºC
Resolution
rES
dE; in
in
in
in
in
In
Probe displayed
Lod
P1; dtr
P1
P1
P1
P1
P1
Not used
dtr
Not used
99
99
Not used
Not used
Defrost type
tdF
EL; in
EL
EL
EL
EL
In
First defrost termination temperature
dtE
(-55 to 50,0ºC)
+6
+5
+5
+6
10
Not used
dts
8
Not used
Not used
8
8
Interval between defrost cycles
idF
0 to 120 hours
6
6
6
6
6
(Maximum) length for first defrost
MdF
0 to 255 min
20
20
20
20
15
(Maximum) length for second defrost
MdS
0 to 255 min
0
0
0
0
0
Start defrost delay
dSd
0 to 255 min
0
0
0
0
0
Displaying during defrost
dFd
Rt; it; Set; dEF
it
it
it
it
dEF
MAX display delay after defrost
dAd
0 to 255 min
15
15
15
15
60
Draining time
Fdt
0 to 255 min
2
2
2
2
3
First defrost after start up
dPo
n;y
n
N
n
n
n
Defrost delay after fast freezing
dAF
0.0 to 24h00
min, res.10 min
0
0
0
0
0
Fan Operating mode
FnC
C-n; o-n; C-Y;
o-Y
C-Y
C-Y
C-Y
C-Y
C-n
Fan delay after defrost
Fnd
0 to 255 min
2
2
2
2
1
Differential of temperature for forced
activation of fans
FCt
0 to 50ºC
0
0
0
0
0
Fan stop temperature
FSt
(-55 to 50.0ºC)
10
10
10
10
0
Fan on time with compressor off
Fon
0 to 15 min
2
2
2
2
1
Fan off time with compressor off
FoF
0 to 15 min
6
6
6
6
5
Kind of action of fan
FSU
Std; FoF; Fon
FoF
FoF
FoF
FoF
FoF
Temperature alarms configuration
ALC
rE; Ab
re
rE
rE
rE
rE
Maximum temperature alarm
ALU
Rel (0.0 to
50.0º) (0 to
90ºF)
Abs: (ALL to
150ºC) (ALL to
302ºF)
7
10
10
7
10

Table of Parameters
DIXELL XR60CH c/ prog. XR 70 CH
DC-09.151-PRD
R02/22.04.2021
Parameters
Code
Range
ASP 400 Snack
ASP 400 FISH
ASP 400 N
LT
NT
NT
LT
LT
Minimum temperature alarm
ALL
Rel (0.0 to
50ºC) (0 to
90ºF)
ABs: (-100ºC to
ALU) (-148ºF to
ALU)
4
4
4
4
5
Differential for temperature alarm
recovery
AFH
(0,1 to 25,5ºC)
(1 to 45ºF)
1
1
1
1
2
Temperature alarm delay
ALd
0 to 255 min
60
60
60
60
120
Delay of temperature
dAo
0,0 to 24h00
min, res.10 min
2
2
2
2
4
2D2efrost relay configuration (1-7/6)
oA1
ALr=alarm;
dEF= do not
select it;
LIG-light;
AUS= AUX,
onF= always on;
Fan= do not
select it;
db=neutral
zone;
CP2=second
compressor;
dF2= do not
select it
deF
deF
deF
deF
deF
Fan relay configuration (1-2)
oA2
ALr=alarm;
dEF= do not
select it; LIG=
light;
AUS=AUX;
onF=always on;
Fan0 do not
select it; db=
neutral zone;
CP2= second
compressor
FAn
FAn
FAn
FAn
FAn
2Digital input polarity (18-19)
i1P
oP; CL
oP
oP
oP
oP
oP
Digital input configuration (18-10)
i1F
EAL; bAL;
PAL; dor;
dEF;ES;AUS;Ht
r; Fan; HdF;
onF
Fan
FAn
FAn
FAn
FAn
Digital input alarm delay (18-20)
did
0 to 255 min
3
3
3
3
3
Second digital input polarity
i2P
oP; CL
CL
CL
CL
CL
CL
Second digital input configuration
i2F
EAL; bAL;
PAL; dor; DEF;
ES; AUS; Htr;
Fan; HdF; onF
EAL
EAL
EAL
EAL
EAL
Second digital input alarm delay
D2d
0 to 255 min
0
0
0
0
0
Number of activations of pressure switch
nPS
0 to 15
15
15
15
15
15
Compress and fan status when open door
odC
No; Fan; CPr;
F-C
no
no
no
no
no
Regulation restart with door open alarm
rrd
N; Y
y
y
Y
y
y
Differential for energy saving
HES
(-30 to 30ºC)
(-54 to 54ºF)
0
0
0
0
0

Table of Parameters
DIXELL XR60CH c/ prog. XR 70 CH
DC-09.151-PRD
R02/22.04.2021
Parameters
Code
Range
ASP 400 Snack
ASP 400 FISH
ASP 400 N
LT
NT
NT
LT
LT
Serial address
Adr
0 to 247
1
1
1
1
1
Kind of probe
PhC
PtC; ntC
ntc
ntc
ntc
ntc
ntc
Room probe display
dP1
Probe value
P1
P1
P1
P1
P1
Evaporator probe display
dP2
Probe value
P2
P2
P2
P2
P2
Third probe display
dP3
Probe value
noP
noP
noP
noP
noP
Software release
rEL
Read only
14.2
14.2
14.2
14.2
14.2
Map code
Ptb
Read only
2
2
2
2
2
MAIN FUNCTIONS:
How to see the set point:
Push and immediately release the SET key: The display will show the Set Point value;
Push and immediately release the SET key or wait for 5 sec to display the probe value again;
How to change the set point
Push the SET key more than 2 second to change the set point value;
The value of the set point will be displayed and the ºC or ºF led will start blinking
To change the set value, push the UP or DOWN arrows within 10 sec
How to start a manual defrost
Push the DEF key for more than 2 sec and a manual defrost will start
How to change a parameter value
To change a parameter value, operate follows:
Enter the programming mode by pressing the SET + DOWN buttons for 3s (the ºC or ºF LED will start blinking)
Select the required parameter. Press the SET button to display its actual value
Use UP or DOWN buttons to change its value.
Press SET button to store the new value move to the following parameter.
To exit: Press SET + UP buttons or waiting for 15 s without pressing any key.
NOTE: the set value is stored even when the procedure is exited by waiting for the time-out expire.
The hidden menu
The hidden menu includes all the parameters of the instrument
-How to enter the hidden menu
Enter the programming mode by pressing the SET + DOWN buttons for 3 sec (the ºC or ºF LED will star
blinking)
Release the buttons and then push again the SET + DOWN buttons for more than 7 s. The Pr2 label will be
displayed immediately followed from HT parameter.
Now i tis possible to browse the hidden menu
Select the required parameter
Press the SET button to display its value
Use UP or DOWN to change its value
Press SET to store the new value and move to the following parameter
To exit: Press SET + DOWN or wait 15 sec without pressing a key
Note1: If no parameter is present in Pr1 menu, after 3 sec the “nop” message will be displayed.
Keep the buttons pushed til the Pr2 message will be displayed
Note2: The set value is stored even when the procedure is exited by waiting for the time-out to expire.