Diamond SA/61G Operation manual

Mod: SA/61G
Production code: SGM 600
11/2011

INSTRUCTIONS FOR USE AND INSTALLATION
GAS SALAMANDERS
SGM 600 / SGM 800 / SGF 800
Made in France
November 2011

GAS SALAMANDERS
SGM 600/SGM 800/SGF 800
Congratulations for the acquisition of this upmarket appliance made in France. You
chose an appliance which alloys the best technical qualities with a big user-
friendliness. We wish you the biggest contentment
1. SECURITY INSTRUCTIONS
Please respect these instructions scrupulously to avoid any risk of fire, scald or other
wounds and damage. During the use of this appliance, fundamental circumspection
of security must always be noticed, such as:
-Take into account the instructions to be systematically kept with the appliance.
-Install the appliance always in instructions respect. A 40 cm distance minimum
with the partition or the wall is necessary.
-Protect the appliance from direct light of the sun, frost and humidity.
-Never leave the appliance within the reach of children or disabled persons with-
out surveillance.
-Never move the appliance when it is working or when the cooking surfaces are
still hot.
-Do not touch the hot surfaces of the appliance. Their temperature can be very
important when the appliance is working. Always use handles and control knobs.
-Do not use the appliance for other functions than determined use.
-Do not leave the pipe or hose (purchased separately from a specialised shop) in
the contact of hot surfaces.
-The appliance should not be used close to combustible materials.
-During use, look after not to obstruct hearings of aeration of the appliance
-Do not bend the pipe or hose
-Entrust compensations only to a skilled person.
-Use only spare parts of origin.
-At the end of cooking, before cleaning the appliance, do not forget to disconnect
the gas inlet.
2. CONTENTS OF CARDBOARD PACKAGING
Device: a salamander
Accessories: - - A tray
-A grid
-A grid with handles (SGF 800)
-A set of natural gas injectors (burner + pilot light)
-The present note
See exploded views for each models at the end of the document 2

3. CONFORMITY OF USE
Use the device only to defrost, brown, glaze, grill toasts, gratins, pizzas, onion
soups.
4. WAY OF FUNCTIONING
These salamanders exist in 11 versions (3 gas versions and 8 electric versions)
SALAMANDERS WITH MOVABLE TOP
Salamanders SGM 600 and SGM 800 are respectively fitted with two infrared burn-
ers with safety thermocouple, a removable inside tray.
The top of the salamander is movable and enables you to adapt the cooking position
to grill, glaze or brown your foodstuffs.
FIXED SALAMANDERS
Salamander SGF 800 is fitted with two infrared burners with safety thermocouple, a
removable inside tray, two racks enabling to adjust the grid with handles on 3 levels
to adapt cooking position.
To turn on the device, just approach a long matchstick or gas lighter near the pilot
light located under the top (n°2 on picture), press and turn the control knob (n°1 on
picture) in front of star position.
Keep the control knob (n°1 on picture) pressed for 15 seconds. The burner then re-
mains lit.
While cooking, the temperature can be regulated using the control knob (n°1 on pic-
ture) from high flame to low flame in order to avoid over-cooking.
A safety thermocouple cuts the gas supply if one of the burner is extinguished. In
this particular case, just turn on the device again as explained before
The low flame of the appliance is pre-adjusted in the factory, it must not be changed.
3

Power control knob + on/off Pilot light
5. FUNCTIONING / HANDLING
a) Installation/Assembly:
-Unpack carefully the machine from its packaging.
-Place the device on a plane and heatproof surface in a well ventilated place.
-Never place the device near a wall or near a partition makes of combustible materi-
als even if it is very well isolated.
-A distance of minimum 40 cm with the partition or the wall is necessary.
-Remove the protective film from the top, the rear, the sides and the tray.
-Unlock the movable top by unscrewing the screw located on the back of the ma-
chine thanks to a 10 pipe key (models SGM 600 and SGM 800).
CAUTION :
During use: never place the machine on surfaces or near walls, partitions or
kitchen furniture and similar—except if they are made with a non combustible
material or recovered with non combustible thermic insulation, and pay atten-
tion to fire preventions rules.
b) First starting:
During the first use, warm your machine up outside during about 30 min to evacuate
residual smokes of manufacturing oil from the metallic parts. This may emit a slight
smell for a few moments.
4
1 2
1
2

First cleaning
Clean the device before the first use. (See 6 Cleaning)
Gas connection
The appliances run on the following gases: Butane G30, Propane G31, Natural gas
G20/G25. The appliances are originally delivered with a Butane/Propane injector
(85/100 for SGM 600, 100/100 for SGM 800 and SGF 800) corresponding to the cate-
gory II2E+3+, under pressure of 28/30/37mbar. The connection is made thanks to a
thread G 1/2.
The heat release rate of the appliance is
-SGM 600 5,3 kW
-SGM 800 8.1 kW
-SGF 800 8,1 kW
Check the supply pressure using a manometer when all the burners are lit. It must be
equal to the indications on the rating plate.
The fresh air flow required for combustion air supply is:
10m3/h
15m3/H
-SGM 600
-SGM 800
-SGF 800 15 m3/H
General conditions of installation
The installation and maintenance of the appliance must be carried out in compliance
with the statutory texts and good practices in force, mainly:
General specifications
For all appliances:
Article GZ Installation with combustible gases and liquefied hydrocarbons.
Then, according to use:
Article CH Heating, ventilation, refrigeration
Air conditioning and domestic hot water steam generation.
Article GC Installation of appliances to be used for catering
Specific provisions for each type of establishment to which the public is admitted
(hospitals, shops, etc…)
Important: Never change the diameter of the injectors.
5

Gas modification for SGM 600
Gas category table, according to the country of destination of the appliance.
6
Country of des-
tination Category Gas Pres- sures Injector
diameter By-Pass screw dia-
meter
Air
setting
ring
France/
Luxembourg II2E+3+ G20/25 20/25 130 Adjustable Without
G30/G31 28-30/37 85 110 Without
II2E+3B/P G20/G25 20/25 130 Adjustable Without
G30/G31 50 75 95 Without
Germany II2E3B/P G20/G25 20 130/142 Adjustable Without
G30/G31 50 75 95 Without
Austria II2H3B/P G20 20 130 Adjustable Without
G30/G31 50 75 95 Without
II2H3B/P G20 20 130 Adjustable WithoutSweden/Danemark
Finland G30/G31 28-30/30 85 110 Without
Spain II2H3+ G20 20 130 Adjustable Without
G30/G31 28-30/37 85 110 Without
II2H3P G20 20 130 Adjustable Without
G31 50 75 95 Without
II2L3B/P G25 25 130 Adjustable Without
G30/G31 28-30/37 85 110 Without
II2L3P G25 25 130 Adjustable Without
G31 50 75 95 Without
Norway I3B/P G30/G31 28-30/30 85 110 Without
Islande/Greece/
Great Britain /Italy II2H3+ G20 20 130 Adjustable Without
Portugal II2H3+ G30/G31 28-30/37 85 110 Without
Netherlands
N°injector Gas Pressure Diameter
Injector n°1 G30/G31 Butane/Propane 28-30/37 85/100
Injector n°2 G30/G31 Butane/Propane 50 75/100
Injector n°3 G20/G25 Natural gas 20-25 130/100
Injector n°4 G25 Natural gas 20 142/100

To change the by-pass screw, unscrew completely the screw located on the left of
the tap and replace it by corresponding screw.
For a use in natural gas, change the injectors (burner + pilot light (Ø 45). They are
delivered in a small plastic bag in the package. Unscrew completely the nut and then
the injector located on the hole. The low flame of the appliance is regulated by un-
screwing the by-pass screw to obtain a flow of 4KW.
Gas modification for SGM 800 and SGF 800
Gas category table, according to the country of destination of the appliance.
Country of des-
tination Category Gas Pres- sures Injector
diameter By-Pass screw dia-
meter
Air
setting
ring
France/
Luxembourg II2E+3+ G20/25 20/25 150 Adjustable Without
G30/G31 28-30/37 100 110 Without
II2E+3B/P G20/G25 20/25 150 Adjustable Without
G30/G31 50 90 95 Without
Germany II2E3B/P G20/G25 20 150/160 Adjustable Without
G30/G31 50 90 95 Without
Austria II2H3B/P G20 20 150 Adjustable Without
G30/G31 50 90 95 Without
II2H3B/P G20 20 150 Adjustable WithoutSweden/Danemark
Finland G30/G31 28-30/30 100 110 Without
Spain II2H3+ G20 20 150 Adjustable Without
G30/G31 28-30/37 100 110 Without
II2H3P G20 20 150 Adjustable Without
G31 50 90 95 Without
II2L3B/P G25 25 150 Adjustable Without
G30/G31 28-30/37 100 110 Without
II2L3P G25 25 150 Adjustable Without
G31 50 90 95 Without
Norway I3B/P G30/G31 28-30/30 100 110 Without
Islande/Greece/
Great Britain /Italy II2H3+ G20 20 150 Adjustable Without
Portugal II2H3+ G30/G31 28-30/37 100 110 Without
Netherlands
7
N°injector Gas Pressure Diameter
Injector n°1 G30/G31 Butane/Propane 28-30/37 100/100
Injector n°2 G30/G31 Butane/Propane 50 90/100
Injector n°3 G20/G25 Gaz naturel 20-25 150100
Injector n°4 G25 Gaz naturel 20 160/100

To change the by-pass screw, unscrew completely the screw located on the left of the tap
and replace it by corresponding screw. For a use in natural gas, change the injectors
(burner + pilot light (Ø 45). They are delivered in a small plastic bag in the package. Un-
screw completely the nut and then the injector located on the hole. The low flame of the
appliance is regulated by unscrewing the by-pass screw to obtain a flow of 6KW.
Air adjustment
Injectors were conceived to avoid any air adjustments and that whatever the gas you use.
c) Use of device :
Elements of command and display
Switching-on
Press the power control knob (n°1 on picture) for a few seconds in front of star posi-
tion.
Use a gas lighter or a long matchstick by holding it near the pilot light (n°2 on picture)
Keep the control knob (n°1 on picture) pressed for some more seconds.
The burner then remains lit and it is now possible to increase the power by turning the
power control knob (n°1 on picture).
Temperature setting
Once the burner is lit, set the appliance to the desired power by turning the control
knob (n°1 on picture).
It is not necessary to leave the device switched on at full power. It is necessary to
adapt the temperature to products to be cooked to limit the gas consumption.
Stopping the appliance
Set each control knob (n°1 on picture) to 0: the appliance is completely switched-off.
Cut the gas supply
Clean the appliance. (See 6. Cleaning)
d) Breakdown / repair:
In case of breakdown or of damaged part, please call your after-sales service and confide
any technical operation to qualified person.
When you contact the after-sales service of your distributor or your store, give him the
complete reference of your device (commercial name, type and serial number). This infor-
mation appears on the visible descriptive plate behind the device.
Command/Display Function
Power control knob
(n°1 on picture) On/off Set the power (low flame = low power, high flame = high
power)
Pilot light (n°2 on pic-
ture) Switch on the machine
8

9
6. CLEANING AND MAINTENANCE
-Cut the gas supply.
-Let cool completely the device before any technical intervention or cleaning.
-For cleaning, only use non-abrasive products, clean regularly the external walls of your
device with warm water and wash liquid: avoid the abrasive towelling. Rinse your device
with a wet sponge.
-Never clean the device under a water jet, the infiltrations would risk to damage it in a ir-
reparable way.
-During a prolonged non-use, we recommend you strongly to keep the device shielded
from the humidity .
7. TECHNICAL SPECIFICATIONS
8. GUARANTEE
Conditions of guarantee
The guarantee applicable to any device is the commercial guarantee of the distributor or
the retailer. Please contact the store where you bought your device to know the precise
conditions.
The guarantee grants no right for damages.
The dispositions which follow are not exclusive of the profit of the legal guarantee planned
by articles 1641 and following ones of the Civil code relative to the defects and the latent
defects.
Exclusion clauses of the guarantee
Bad installation and bad maintenance, in particular if they do not respect current
regulations or instructions appearing in this user guide.
Cannot benefit from the guarantee the repairs required as a result of false operations, of
inappropriate use, of carelessness or of excess loads of the device, as well as those result-
ing from defective installations.
The damage due to shocks, bad weather is not flatware by the guarantee. The material
travels at the risks of the user; in case of delivery by carrier, the consignee has to have
reservations towards the carrier before any delivery of the device.
The guarantee comes to an end in case of intervention, of repair, of modification by no
qualified persons, or of use in inappropriate purposes.
Models SGM 600 SGM 800
Outisde dimensions 600x590x590mm 800x590x590 mm
Weight 49 Kg 57 Kg
Power 5300 W 8100 W
Cooking surface 495x375 mm 740x375 mm
Nb of burner 2 2
SGF 800
800x590x590 mm
40 Kg
8100 W
740x375 mm
2