Digicom POS 360 Series User manual

POS 360 Series
User Manual
Point-of-Sale
Hardware System
2007 January V1.0

Copyright 2007 January
All Rights Reserved
Manual Version 1.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of
this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced or
translated to another language without the prior written consent of the
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.

3
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrial power supply, turn off the power
switch and remove the power cord plug from the wall socket. The wall socket
must be easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart,stand,or table.The product may
fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation;to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered.The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface.This product should never be placed near or over a radiator or
heat register,or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the
marking label.If you are not sure of the type of power available, consult your
dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product
where persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the product.
CE MARK
This device complies with the requirements of the EEC directive
89/336/EEC with regard to “Electromagnetic compatibility” and
73/23/EEC “Low Voltage Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.

4
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the
treatment, collection, recycling and disposal of electric and electronic
devices and their components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.

5
Table of Contents
1. Item Checklist ................................................................................................6
1.1. Standard Items......................................................................................6
1.2. Optional Items.......................................................................................6
2. System View ..................................................................................................7
2.1. Front View.............................................................................................7
2.2. Side View..............................................................................................7
2.3. Rear View .............................................................................................8
2.4. Bottom View..........................................................................................8
2.5. I/O View ................................................................................................9
3. Driver Installation .........................................................................................10
3.1. Driver List............................................................................................10
3.2. Chipset Driver Installation ...................................................................10
3.3. USB 2.0 Driver Installation..................................................................12
3.4. VGA Driver Installation........................................................................15
3.5. ELO Touch Driver Installation..............................................................16
3.6. POSTouch Driver Installation ..............................................................18
3.7. 10/100Mb LAN Driver Installation .......................................................21
4. Peripherals Installation.................................................................................22
4.1. Magnetic Card Reader Installation......................................................22
4.2. Cash Drawer Installation.....................................................................23
5. System Disassembly ...................................................................................25
5.1. Replacing HDD ...................................................................................25
5.2. Replacing Mainboard & I/O Board ......................................................26
5.3. Replacing the Customer Display.........................................................27
5.4. Replacing the Fan...............................................................................28
5.5. Replace Inverter Board & Touch Screen Board ..................................29
6. Specification.................................................................................................30
7. Jumper Settings...........................................................................................32
7.1. Connectors .........................................................................................33
7.2. Jumper Settings..................................................................................33
7.3. Connectors Pin Definition ...................................................................35
8. BIOS Settings ..............................................................................................39
8.1. BIOS Setup Utility ...............................................................................39
8.2. Starting the BIOS Setup......................................................................39
8.3. When a Problem Occurs.....................................................................39
8.4. BIOS Main Menu.................................................................................39

6
1. Item Checklist
Take the system unit out of the carton. Remove the unit from the carton by holding
it by the foam inserts. The following contents should be found in the carton:
1.1. Standard Items
a. Driver CD b. System
c. Power Cable
1.2. Optional Items
a. Customer Display b. MSR

7
2. System View
2.1. Front View
2.2. Side View
MSR
Power
LED
Tilt Angle 65˚~ -25˚
Ventilation
Pole type VFD
Small Footprint

8
2.3. Rear View
2.4. Bottom View
Flush mount VFD
Rear I/O
Robber Foot
VESA

9
2.5. I/O View
Note: The maximum current that can be drawn from each COM port is 500 mA.
Only one PS/2 keyboard can be connected to the system: either on the
side or in the rear.
LAN
DC Jack
2
nd
VGA
Parallel
USB
(4)
COM
(4)
Line in
Line out
Cash
Drawer

10
3. Driver Installation
3.1. Driver List
Folder/File File Description
<CD>:\POS360_B78.htm B78 Driver List
<CD>:\COMMON\INTEL\Chipset Chipset Driver
<CD>:\COMMON\INTEL\USB 20 USB 2.0 Driver
<CD>:\COMMON\INTEL\VGA\i85x VGA Driver
<CD>:\COMMON\Elo_Touch ELO Touch Driver
<CD>:\COMMON\POS_Touch POSTouch Driver
<CD>:\COMMON\Lan_driver\R8139_810x\V3.00.504 10/100Mb LAN Driver
-The following procedures are for Windows 2000/XP, other platforms are similar.
3.2. Chipset Driver Installation
a. Double click “infinst_enu_6.0.1.1002”
on the My computer window.
b. Click the “Next” button on the
Welcome window.