Digimerge DPV24D User manual

Please read this manual thoroughly before use and keep it handy for future reference.
Vandal Models: DPV24D / DPV24TLX
Indoor Models: DPD23D / DPD24D
Ultra Resolution
Day & Night Dome Camera
INSTRUCTION MANUAL

INTRODUCTION
Features
All Models Feature:
• 1/3”SonySuperHAD™IICCD
• Excellentlowlightperformanceusing
 PolarisVision2technology.
• 0.15Lux/F1.2(Color)
 0.001Luxw/Sense-Upatx256
• 600TVlines(Color)ofresolution
• 3DDigitalNoiseReduction(3D-DNR)
• OSDmenucontrol
• PrivacyMasking/MotionDetection
• VIDEOOUT(BNC)
• Operatesin12VDCor24VAC
• TestMonitorOutput
• CameraMounting:Surface/Flushmounting
  (IndoorModelonly)
DPD23D
• IndoorDomeModel
• 3.6mmFixedLens
DPD24D
• IndoorDomeModel
• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris
DPV24D
• VandalResistantDomeModel
• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris
DPV24TLX
• VandalResistantDomeModel
• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris
• SmartIRtechnology
• ICRltertogiveclearnightvision
• ArcticProtechnologywithbuilt-inheater
• 0LuxwithIRLED
General DPD23D DPD24D DPV24D DPV24TLX
Power source DC 12V / AC 24V +10%
Power consumption 2.5 Watts 10 Watts
(Heater On)
Image sensor 1/3”SonySuperHAD™IICCD
Total pixels 811 (H) x 508 (V)
Scanning system 2:1 interlace
Scanning frequency 15.734KHz(H), 59.95Hz(V)
Sync.system Internal / Line Lock
Resolution 600 TV Lines
Min.Illumination 0.15Lux / 0.001Lux
Sense Up at x256 0 Lux IR LED On
Video output 1.0 Vp-p (75 ohm, composite)
S/N Ratio more than 50dB (AGC OFF)
Operating Temperature -10°C - +50°C -40°C - +50°C
Power input 2-Pin terminal block (Detachable)
Video output BNC Connector (2nd video RCA)
Lens mount Fixed mount
Lens 3.6mm Fixed 2.8 - 10.5mm F1.4 Varifocal DC Auto iris
Operating humidity 0-90% (non-condensing)
SPECIFICATIONS
-1-

-2-
MEASUREMENTS
Vandal Dome Dimensions
3/4’’ -14
NPS thread
97.0 mm
3.82 in
Base hole positions
40 mm
1.57 in
55.5 mm
2.19 in
Ø 0.1"
3.5 mm
3.9"
100.0 mm
3.4"
87 mm
5.1"
130 mm
112 mm
4.4 in
112 mm
4.4 in
39 mm
1.5 in
115 mm
4.5 in
27 mm
1.1 in
137°
123°
100°
7 mm
.28 in
Underside Base hole positionsIndoor Dome Dimensions
Recess cutout and tting clearance.Recess Mount Fitting dimensions
5.1"
130 mm

-3-
PACKING CONTENTS
Indoor Dome package contains the following:
Camera in housing ---------------------------------1
Camera Locking screws (PA3 Type) -----------2
Instruction guide (This Document)-------------1
Surface & Flush Mounting Templates----------2
RCA - BNC test cable------------------------------1
Junction Box Plate----------------------------------1
Mounting screw pack ------------------------------1
Vandal Dome package contains the following:
Camera in housing ---------------------------------1
Camera Locking screws (PM4 Type) ----------3
Instruction guide (This Document)-------------1
Surface Mounting Template ----------------------1
RCA - BNC test cable------------------------------1
Junction Box Plate----------------------------------1
Mounting screw pack ------------------------------1
Tamper allen key------------------------------------1
Conduit Key ------------------------------------------1
Junction box plate allows tting of either Vandal dome or
Indoor dome to standard 2S, 4S and Octagon junction
boxes.
NOTE: Flush side of junction box plate should be attached
to junction box
Junction Box tting plate accessories:
Junction Box Fitting plate ------------------------1
2S / 4S plate screws (KM3.5 Type) ------------4
Octagon tting screws (KM4 Type)-------------2
Base Fitting Screws PWM3 ----------------------3
JUNCTION BOX PLATE
Screw hole overview Vandal dome tting illustration Junction box tting plate attached to camera
Base Fitting
Screws
88.9 mm
3.5 in
83.3 mm
3.28 in
46.0 mm
1.8 in
Base Fitting
Screw.
Octagon
Screw
2S / 4S
Screw
Locking
Screw
Conduit
Key
Allen Key
Mounting Screws Pack.
3pc 70mm / 2.8in Screws
3pc 30mm / 1.2in Screws
3pc 40mm 1.6in plugs

-4-
JUNCTION BOX INSTALLATION TYPES
2S FITTING
a. 2S Fitting requires only 2pcs of base
attachment screws.
Note: You have a reduced space in which
to hide cables using this type of
installation. Recommended for indoor
dome only.
TWO GANG FITTING
a. Two gang tting (switch box) requires 4pcs
of base attachment screws.
Note: A two gang provides the most robust
tting. Suitable for both indoor and
vandal domes.
4S FITTING
a. 4S Fitting requires 2pcs of base attachment
screws.
Note: Screws used for the 4S box are larger
compared to those used for the 2S (M4
type). Suitable for both indoor and
vandal domes
OCTAGON FITTING
a. 4” Octagon tting requires only 2pcs of
base attachment screws.
Note Screws used for the octagon tting
are larger compared to those used for
the 2S/4S (M4 type). Suitable for both
indoor and vandal domes
Cable
Entry
Screws
Cable
Entry
Screws
Cable
Entry
Screws
Cable
Entry
Screws

-5-
VANDAL DOME FITTINGS
Pendant Cap - model # MNTV2XPC
Replaces the need for the camera base.
Compatible with ceiling conduit installations
Pole Mount - model # MNTV2XPJunction Box Accessory - model # MNTV2XJ
Fits either wall mount and corner mount bracket.
Symmetrical so reversible for top or bottom
conduit.
Corner Mount bracket - model # MNTV2XR
Can t either Wall Bracket or Junction Box. Pendant Mount - model # MNTV2XC
Wall Mount - model # MNTV2XW

-6-
INSTALLATION. VANDAL DOME
1) Remove the three tamper screws using the provided
allen key. Size is standard T-15
Note: If you plan to use conduit tting, remove conduit
cap using the prodivded conduit key.
DPV24TLX ONLY
When using DC power, note the correct polarity stated on the
label attached to the power cord.
Note: If you plan on installing onto a junction
box, attach provided tting plate rst to
the junction box and then you attach the
camera base to the tting plate.
3a) Reinsert camera module into camera base
by ligning up the arrow notches, and turning
camera module clockwise to lock into place.
3b) Use the supplied three base locking screws to
secure camera base to camera module.
Go to step 4on page 7 to complete installation.
Method 1 - Direct Attach Install
2a) Use included mounting template to mark and pre-
drill the required holes. Use 2pc of the 2.8” screws
to mount the camera directly to the mounting
surface.
Remove (one base locking screw, used for shipping
purposes) and install the 3rd 2.8” screw.
Go to step 4on page 7 to complete installation.
OR
Method 2 - Camera Base Install
Note: Use this method if installing onto junction box
plate.
2b) Remove the camera base by unscrewing the base
locking screw, and turn camera module approx. 5
degrees counter-clockwise to detach camera base
from the camera module. Now you install the base
to the correct holes as indicated on the mount
template using the 1.2” screws.
1
3
a
b
a
b
2

-7-
INSTALLATION. VANDAL DOME
7a) Re-attach the camera cover. Line up arrows as shown in
gure 3a on page 6 as a guide
7b) Use the allen key to tighten the tamper screws to create
a proper weatherproof seal.
Note: Make sure dome cover cord does not get caught in
the rubber seal.
1) Remove the three tamper screws using the provided
allen key. Size is standard T-15
Note: If you plan to use conduit tting, remove conduit
cap using the prodivded conduit key.
DPV24TLX ONLY
When using DC power, note the correct polarity stated on the
label attached to the power cord.
Method 1 - Direct Attach Install
2a) Use included mounting template to mark and pre-
drill the required holes. Use 2pc of the 2.8” screws
to mount the camera directly to the mounting
surface.
Remove (one base locking screw, used for shipping
purposes) and install the 3rd 2.8” screw.
Go to step 4on page 7 to complete installation.
OR
Method 2 - Camera Base Install
Note: Use this method if installing onto junction box
plate.
2b) Remove the camera base by unscrewing the base
locking screw, and turn camera module approx. 5
degrees counter-clockwise to detach camera base
from the camera module. Now you install the base
to the correct holes as indicated on the mount
template using the 1.2” screws.
6a) Adjust camera viewing angle and secure into place by
tightening thumb screw using a at head screwdriver.
6b) Adjust lens and OSD as required.
6c) Re-attach the camera cover, using the thumb screw
as a guide, until it snaps into place.
Note: Lens adjustment levers are by default in the
locked position. Turn counter clockwise to unlock.
Tighten levers to secure lens setting.
5) Insert the included video test cable into the RCA jack
and connect to a test monitor to set up camera.
4) Remove camera cover by squeezing the back and front
of the cover as indicated by the “PRESS” indicators at
the same time and lifting it up and away from the lens.
7
5
6
4

-8-
INSTALLATION. INDOOR DOME (Surface Fitting)
1a) Press down on the tab marked with an arrow to lift
up the dome cover slightly
1b) While pressing on tab, twist the dome cover
counter clockwise just a few degrees to release
dome cover from back clips.
Lift off the cover.
Note: If you plan on installing onto a junction box,
attach provided mounting plate rst to the
junction box and then attach camera base
to the mounting plate.
3a) Reinsert camera module into camera base
by ligning up the arrow notches, and turning
camera module clockwise to lock into place.
3b) Reinstall the base locking screws. (indicated by
padlock markings)
Go to step 3on page 9 to complete installation.
Method 1 - Direct Attach Install
2a) Use included mounting template to mark and pre-
drill the required holes. Use included 2.8” screws
to mount the camera directly to the mounting
surface.
Go to step 3on page 9 to complete installation.
OR
Method 2 - Camera Base Install
Note: Use this method if installing onto junction box
plate.
2b) Remove the camera base by unscrewing the base
locking screws (indicated by padlock markings)
and turn camera module approx. 5 degrees
counter-clockwise to detach camera base from the
camera module. Install the base as indicated using
the 1.2” screws.
1
3
a
a
b
a
b
b
2

-9-
INSTALLATION. INDOOR DOME (Semi-Flush Fitting)
1a) Press down on the tab marked with an arrow to lift
up the dome cover slightly
1b) While pressing on tab, twist the dome cover counter-
clockwise to release dome cover
1c) Remove the camera base by unscrewing the base
locking screws (indicated by a padlock markings)
and turn camera module approx. 5 degrees counter-
clockwise to detach camera base from the camera
module.
1a) Press down on the tab marked with an arrow to lift
up the dome cover slightly
1b) While pressing on tab, twist the dome cover
counter clockwise just a few degrees to release
dome cover from back clips.
Lift off the cover.
Method 1 - Direct Attach Install
2a) Use included mounting template to mark and pre-
drill the required holes. Use included 2.8” screws
to mount the camera directly to the mounting
surface.
Go to step 3on page 9 to complete installation.
OR
Method 2 - Camera Base Install
Note: Use this method if installing onto junction box
plate.
2b) Remove the camera base by unscrewing the base
locking screws (indicated by padlock markings)
and turn camera module approx. 5 degrees
counter-clockwise to detach camera base from the
camera module. Install the base as indicated using
the 1.2” screws.
a) Cut semi ush mounting hole into surface using
provided ush mounting template.
Note: Always cut according to the inside of the cutout
template
b) Insert dome into cutout. Make sure that the
mounting arms are not extended.
c) Turn screwdriver clockwise to unlock all of the 3
mounting arms.
d) Continue turning clockwise to move mounting arms
down until they make contact with inner mounting
surface.
Note: Once mounting arms have made contact with
the inner mounting surface, do not apply too
much pressure to avoid damaging surface.
a) Re-attach the camera cover, using the thumb screw as a guide, until it snaps into
place.
b) Reattach dome cover.
a) Remove camera cover by squeezing the back and front
of the cover as indicated by the “PRESS” indicators at
the same time and lifting it up and away from the lens.
b) Insert the included video test cable into the RCA jack
and connect to a test monitor to set up camera. (see
page 10)
c) Adjust camera viewing angle and secure into place by
tightening thumb screw using a at head screwdriver.
Adjust lens and OSD as required.
Note: Lens adjustment levers are by default in the locked
position. Turn counter clockwise to unlock. Tighten
levers to secure lens setting.
1
a
b
d
c
b
4
2
3

-10-
CAMERA ADJUSTMENT
1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. DAY NIGHT AUTO
5. 3DNR OFF
6. SPECIAL
7. ADJUST
8. RESET
9. EXIT
1. LENS DC
LENS •DCorMANUAL(ModelDPD23D)
EXPOSURE •SHUTTER•AGC•SENS-UP•BLC•D-WDR•RETURN
WHITEBAL •AWB•ATW•AWCSET•OUTDOOR•INDOOR•MANUAL
DAY/NIGHT•AUTO•COLOR•B/W
3DNR •OFF•ON
SPECIAL •CAMTITLE•D-EFFECT•MOTION•PRIVACY
 •SYNC•LANGUAGE
ADJUST •SHARPNESS•MONITOR•OSDCOLOR
RESET •FACTORY•RETURN
MENU TREE SUMMARY
•NOTE
The brightness level can be adjusted within
the range of 0 - 100. Default setting - 50
With Model DPD23D DC Lens setting is MANUAL
The EXPOSURE menu is used to set the automatic
light control method for the camera.
1. Highlight 'EXPOSURE' in the main setup menu
2. Press the joystick to access the exposure setup menu.
EXPOSURE
Using this function, you can control screen brightness.
1. Highlight 'LENS' in the main setup menu
2. Press the joystick to access the DC lens setup menu.
3. After completing setting update, highlight 'RETURN' to save setting and return to previous menu
SHUTTER : Select the shutter mode. (1/60, FLK - 1/100,000 sec, x2 - 256)
Default setting is 1/60
AGC: Auto gain control (LOW / MIDDLE / HIGH)
Default setting is MIDDLE
LENS
SETUP
1. LENS DC
2. EXPOSURE
SETUP
1. LENS DC
2. EXPOSURE
3. WHITE BAL MANUAL
EXPOSURE
 
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
LENS

RETURN RET
1. Press down on the function joystick to access the setup menu.
• Main setup menu is displayed on the monitor screen.
2. Select a function by moving the joystick up and down and move left or right to change
setting value and press joystick to conrm selection.
3. If a menu option features a ' ', a sub menu is available which can be accessed by pressing
down on the joystick
4. Once nished updating settings, highlight 'EXIT' and press down on the joystick
to exit setup menu
Menu Setup
OSD function joystick. Pressing down
on joystick acts as ENTER function.
RCA Service Connector
Use supplied RCA - BNC cable
If you require BNC output.

-11-
CAMERA ADJUSTMENT
•NOTE
The brightness level can be adjusted within
the range of 0 - 100. Default setting - 50
With Model DPD23D DC Lens setting is MANUAL
The EXPOSURE menu is used to set the automatic
light control method for the camera.
1. Highlight 'EXPOSURE' in the main setup menu
2. Press the joystick to access the exposure setup menu.
EXPOSURE
Using this function, you can control screen brightness.
1. Highlight 'LENS' in the main setup menu
2. Press the joystick to access the DC lens setup menu.
3. After completing setting update, highlight 'RETURN' to save setting and return to previous menu
SHUTTER : Select the shutter mode. (1/60, FLK - 1/100,000 sec, x2 - 256)
Default setting is 1/60
AGC: Auto gain control (LOW / MIDDLE / HIGH)
Default setting is MIDDLE
LENS
SETUP
1. LENS DC
2. EXPOSURE
SETUP
1. LENS DC
2. EXPOSURE
3. WHITE BAL MANUAL
EXPOSURE
 
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
LENS

RETURN RET
1. Press down on the function joystick to access the setup menu.
• Main setup menu is displayed on the monitor screen.
2. Select a function by moving the joystick up and down and move left or right to change
setting value and press joystick to conrm selection.
3. If a menu option features a ' ', a sub menu is available which can be accessed by pressing
down on the joystick
4. Once nished updating settings, highlight 'EXIT' and press down on the joystick
to exit setup menu
Menu Setup
OSD function joystick. Pressing down
on joystick acts as ENTER function.
RCA Service Connector
Use supplied RCA - BNC cable
If you require BNC output.

-12-
CAMERA ADJUSTMENT
Select digital slow shutter speed setting in order to allow extra light into the camera
thereby providing higher sensitivity in low light conditions. NOTE only adjustable
if SHUTTER setting is set to 'AUTO' or '1/60'
- OFF : Deactivates the SENS-UPfunction.
Selectable low shutter values are as follows:
x2 x4 x8 x16 x32 x64 x128 x 256 (default - x8)
For proper setup, check setting during low light / night time conditions.
- AUTO :Activates SENS-UP function. Enter submenu to select maximum low shutter value
•It's recommended to keep the value in the x2 to x64 range to limit ghosting
effect.
Notes
SENSE-UP
SENSE-UP x�
RETURN RET
SENSE-UP
EXPOSURE
SHUTTER 1/60
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
The BLC menu is used to adjust backlight compensation function to sharpen subjects in backlight situations
1. Highlight 'BLC' in the exposure setup menu.
2. Press the joystick to access the BLC setup
menu.
BACKLIGHT (BLC)
BLCOFF
HSBLC (Highlight Compensation):
If a scene contains very bright light sources (e.g. car headlights),they will be masked
to provide greater detail in the rest of the scene.
Enter the HSBLC submenu to select an area in the scene which requires masking.
Change the LEVEL value to set level of masking and change MODE to set whether
to mask all day long or during low light conditions only.
Default setting is OFF
EXPOSURE
SHUTTER 1/60
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
BLC (Backlight Compensation):
Enter the BLC submenu to select an area in
the scene which requires enhancing.
Change the GAIN value (LOW/MIDDLE/HIGH)
to set level of enhancement.
BLC
GAIN LOW
AREA
DEFAULT
RETURN RET

-13-
CAMERA ADJUSTMENT
Select digital slow shutter speed setting in order to allow extra light into the camera
thereby providing higher sensitivity in low light conditions. NOTE only adjustable
if SHUTTER setting is set to 'AUTO' or '1/60'
- OFF : Deactivates the SENS-UPfunction.
Selectable low shutter values are as follows:
x2 x4 x8 x16 x32 x64 x128 x 256 (default - x8)
For proper setup, check setting during low light / night time conditions.
- AUTO :Activates SENS-UP function. Enter submenu to select maximum low shutter value
•It's recommended to keep the value in the x2 to x64 range to limit ghosting
effect.
Notes
SENSE-UP
SENSE-UP x�
RETURN RET
SENSE-UP
EXPOSURE
SHUTTER 1/60
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
The BLC menu is used to adjust backlight compensation function to sharpen subjects in backlight situations
1. Highlight 'BLC' in the exposure setup menu.
2. Press the joystick to access the BLC setup
menu.
BACKLIGHT (BLC)
BLCOFF
HSBLC (Highlight Compensation):
If a scene contains very bright light sources (e.g. car headlights),they will be masked
to provide greater detail in the rest of the scene.
Enter the HSBLC submenu to select an area in the scene which requires masking.
Change the LEVEL value to set level of masking and change MODE to set whether
to mask all day long or during low light conditions only.
Default setting is OFF
EXPOSURE
SHUTTER 1/60
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
BLC (Backlight Compensation):
Enter the BLC submenu to select an area in
the scene which requires enhancing.
Change the GAIN value (LOW/MIDDLE/HIGH)
to set level of enhancement.
BLC
GAIN LOW
AREA
DEFAULT
RETURN RET

-14-
CAMERA ADJUSTMENT
D-WDR :
1. Highlight 'D-WDR' in the exposure
setup menu.
2. Move the the joystick left/right to
change setting to OFF/INDOOR/OUTDOOR.
Default setting is OFF
The D-WDR menu is used to adjust dynamic range of the camera electronically.
This is especially useful in high contrast scenes in order to brighten up
darker parts of the scene.
White balance function adjusts displayed colors to account for different lighting temperatures.
1. Highlight 'WHITE BAL' in the main setup menu.
2. Move the the joystick left/right to change setting to:
AWB/AWC->SET/MANUAL/INDOOR/OUTDOOR/ ATW
Default setting is AWB (Auto White Balance)
White Balance (White Bal.)
Wide Dynamic Range (E-WDR)
EXPOSURE
SHUTTER 1/60
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
INDOOR : Preferred setting when camera is installed indoors.
Default settings are LOW-6 and HIGH-9
OUTDOOR ::
Preferred setting when camera is installed outdoors.
Default settings are LOW-11 and HIGH-11
D-WDR INDOOR
LOW-LEVEL ----|---- �
HIGH-LEVEL ----|---- �
RETURN RET
AWB(Automatic White Balance) : This mode automatically adjusts white balance
AWC-SET : To obtain the optimum state under the current luminance
levels, direct the camera to point toward a sheet of white paper
and press the SET button. If the environment changes, including
the light source, the white balance will require re-adjustment.
MANUAL : The manual adjustment setting enables
detailed color adjustment. Select 'ATW' or 'AWB' rst
then change to 'MANUAL' adjustment setting and press
the joystick. Set the appropriate color temperature
by increasing / decreasing the red and blue color values
and monitor the color changes of the object.
Default settings are BLUE-41, RED-45
INDOOR : Select this when the color temperature is between 4,500˚K
and 8,500˚K.
OUTDOOR : Select this when the color temperature is between 1,800˚K
and 10,500˚K. (sodium light)
ATW(Auto Tracking White Balance) : This mode can be used within the color temperature
range 1,800˚K ~ 10,500˚K
•White Balance may not work properly under the following conditions. In this case
select the AWC mode.
1 When the color temperature of the environment surrounding the subject is outside
of the supported temperature range (e.g. clear sky or sunset).
2 When the ambient illumination of the subject is dim.
3 If the camera is directed towards a uorescent light or is installed in a place
where illumination changes dramatically, the White Balance function may become
unstable.
Notes
SETUP
1. LENS DC
2. EXPOSURE
3. WHITE BAL AWB
4. DAY NIGHT AUTO
WHITE BAL MANUAL
 
 
RETURN RET

-15-
CAMERA ADJUSTMENT
D-WDR :
1. Highlight 'D-WDR' in the exposure
setup menu.
2. Move the the joystick left/right to
change setting to OFF/INDOOR/OUTDOOR.
Default setting is OFF
The D-WDR menu is used to adjust dynamic range of the camera electronically.
This is especially useful in high contrast scenes in order to brighten up
darker parts of the scene.
White balance function adjusts displayed colors to account for different lighting temperatures.
1. Highlight 'WHITE BAL' in the main setup menu.
2. Move the the joystick left/right to change setting to:
AWB/AWC->SET/MANUAL/INDOOR/OUTDOOR/ ATW
Default setting is AWB (Auto White Balance)
White Balance (White Bal.)
Wide Dynamic Range (E-WDR)
EXPOSURE
SHUTTER 1/60
AGC MIDDLE
SENSE-UP AUTO
BLC OFF
D-WDR OFF
RETURN RET
INDOOR : Preferred setting when camera is installed indoors.
Default settings are LOW-6 and HIGH-9
OUTDOOR ::
Preferred setting when camera is installed outdoors.
Default settings are LOW-11 and HIGH-11
D-WDR INDOOR
LOW-LEVEL ----|---- �
HIGH-LEVEL ----|---- �
RETURN RET
AWB(Automatic White Balance) : This mode automatically adjusts white balance
AWC-SET : To obtain the optimum state under the current luminance
levels, direct the camera to point toward a sheet of white paper
and press the SET button. If the environment changes, including
the light source, the white balance will require re-adjustment.
MANUAL : The manual adjustment setting enables
detailed color adjustment. Select 'ATW' or 'AWB' rst
then change to 'MANUAL' adjustment setting and press
the joystick. Set the appropriate color temperature
by increasing / decreasing the red and blue color values
and monitor the color changes of the object.
Default settings are BLUE-41, RED-45
INDOOR : Select this when the color temperature is between 4,500˚K
and 8,500˚K.
OUTDOOR : Select this when the color temperature is between 1,800˚K
and 10,500˚K. (sodium light)
ATW(Auto Tracking White Balance) : This mode can be used within the color temperature
range 1,800˚K ~ 10,500˚K
•White Balance may not work properly under the following conditions. In this case
select the AWC mode.
1 When the color temperature of the environment surrounding the subject is outside
of the supported temperature range (e.g. clear sky or sunset).
2 When the ambient illumination of the subject is dim.
3 If the camera is directed towards a uorescent light or is installed in a place
where illumination changes dramatically, the White Balance function may become
unstable.
Notes
SETUP
1. LENS DC
2. EXPOSURE
3. WHITE BAL AWB
4. DAY NIGHT AUTO
WHITE BAL MANUAL
 
 
RETURN RET

-16-
CAMERA ADJUSTMENT
The DAY/NIGHT menu is used to congure the day and night related settings for the camera.
1. Highlight 'DAY&NIGHT' in the main setup menu
2. Move the the joystick left/right to change setting to AUTO/COLOR/ B/W
3. Press the joystick to access the submenu's for AUTO and B/W settings
DAY/NIGHT
COLOR :The picture is always displayed in color.
B/W :The picture is always displayed in black and
white. Press joystick to turn ON or OFF
the burst signal in B/W mode.
AUTO :The mode is switched to ‘Color ’ ina normal
environment, but switches to ‘B/W’mode
when ambient illuminationis low.To set up
the switching time or speed for AUTOmode,
press the joystick.
You can now set the Delay in seconds
for the Day - Night and the Night - Day
transitions.
DAY NIGHT AUTO
 
 
 
RETURN RET

BURST OFF
RETURN RET
SETUP
1. LENS DC
2. EXPOSURE
3. WHITE BAL
4. DAY NIGHT
MANUAL
AUTO
This function reducesthe background noise in a low luminance environment.
1.Highlight '3DNR' in the main setup menu.
2. Move the the joystick left/right to change setting to OFF/ON
OFF - Noise is not reduced
ON - Noise is reduced
3. Press the joystick to access the submenu for ON setting.
In the 3DNR submenu you can adjust the noise reduction level values range
from 0 to 100. Default setting is 60.
Digital Noise Reduction (3D DNR)
•Noise levels can be very subtle, and may not be always noticable on adjusting
•When adjusting the noise reduction level in 3DNR submenu, remember that the
higher the level set, the more the noise level will be reduced, however this can
have a softening effect on the image.
Notes

 
RETURN RET
SETUP
1. LENS DC
2. EXPOSURE
3. WHITE BAL
4. DAY NIGHT
MANUAL
AUTO
5. 3DNR ON