Digital Equipment VAX 4000 Model 500A User manual

VAX4000
Model500A/505A/600A/700A/705A
Installation
Order Number: EK–493AB–IN. B01
Digital Equipment Corporation
Maynard, Massachusetts

First Edition, March 1990
Seventh Edition, July 1994
The information in this document is subject to change without notice and should not be construed
as a commitment by Digital Equipment Corporation.
Digital Equipment Corporation assumes no responsibility for any errors that may appear in this
document.
The software, if any, described in this document is furnished under a license and may be used or
copied only in accordance with the terms of such license. No responsibility is assumed for the use
or reliability of software or equipment that is not supplied by Digital Equipment Corporation or its
affiliated companies.
Restricted Rights: Use, duplication or disclosure by the U.S. Government is subject to restrictions
as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause
at DFARS 252.227–7013.
Copyright © Digital Equipment Corporation 1990, 1994. All Rights Reserved.
The Reader’s Comments form at the end of this document requests your critical evaluation to assist
in preparing future documentation.
The following are trademarks of Digital Equipment Corporation: CompacTape, CX, DDCMP, DEC,
DECconnect, DECdirect, DECnet, DECscan, DECserver, DECUS, DECwindows, DELNI, DEMPR,
DESQA, DESTA, DSRVB, DSSI, IVAX, KDA, KLESI, KRQ50, MicroVAX, MSCP, Q–bus, Q22–bus,
RA, RQDX, RV20, SA, SDI, ThinWire, TK, TMSCP, TQK, TS05, TU, VAX, VAX 4000, VAXcluster,
VAX DOCUMENT, VAXELN, VAXlab, VAXserver, VMS, VT, and the DIGITAL logo.
All other trademarks and registered trademarks are the property of their respective holders.
FCC NOTICE: The equipment described in this manual generates, uses, and may emit radio
frequency. The equipment has been type tested and found to comply with the limits for a Class A
computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such radio frequency interference.
Operation of the equipment in a residential area may cause interference, in which case the user
at his own expense will be required to take whatever measures may be required to correct the
interference.
Warning: The VAX 4000 Model 705A is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take adequate measures.
Achtung! Der VAX 4000 Modell 705A ist ein Gerät der Funkstörgrenzwertklasse A. In
Wohnbereichen können bei Betrieb dieses Geräts Rundfunkstörngen auftreten, in welchen Fällen
der Benutzer für entsprechende Gegenmaßnahmen verantwortlich ist.
Attention! Le VAX 4000 modèle 705A est un produit de Classe A. Dans un environnement
domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à
l’utilisateur de prendre les mesures spécifiques appropriées.
S2578
This document was prepared using VAX DOCUMENT Version 2.1.

Contents
1Verify Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2ChecktheShipment.............................. 2
3PositiontheSystem.............................. 5
4OpentheSystemDoors ........................... 6
5Install the Console Terminal . . . . . . . . . . . . . . . . . . . . . . . 8
6Set the System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7Connect Additional Devices to the System . . . . . . . . . . . . . 16
7.1 Connecting Terminals and Serial Printers . . . . . . . . . . 19
7.2 Connecting Parallel Printers . . . . . . . . . . . . . . . . . . . . 23
7.3 Connecting Synchronous Modems . . . . . . . . . . . . . . . . 25
7.4 Connecting Asynchronous Modems . . . . . . . . . . . . . . . 29
7.5 Connecting to an Ethernet Network at the H3604
ConsoleModule .............................. 33
7.5.1 Making a ThinWire Network Connection . . . . . . . . 34
7.5.2 Making a Standard Network Connection . . . . . . . . 38
7.6 Connecting to an Ethernet Network at the DESQA
Module..................................... 40
7.6.1 Making a ThinWire Network Connection . . . . . . . . 41
7.6.2 Making a Standard Network Connection . . . . . . . . 46
8ConnectanExpander............................. 48
8.1 Connecting the Q–Bus Cables . . . . . . . . . . . . . . . . . . . 49
8.2 Connecting the DSSI Cable . . . . . . . . . . . . . . . . . . . . . 50
8.3 Connecting the KZQSA External Cable . . . . . . . . . . . . 53
8.4 Connecting the Power Control Bus Cable . . . . . . . . . . 55
8.5 Connecting the Ground Cable . . . . . . . . . . . . . . . . . . . 56
9Connect the System Power Cable . . . . . . . . . . . . . . . . . . . . 56
10 Turn On the System and Select a Language . . . . . . . . . . . 58
11 Close the System Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
12 AfterInstallation................................ 62
iii

Index
iv

1 Verify Site Preparation
Caution
Review your system warranty. It may require that a Digital service
representative install your system to prevent damage to equipment or
software.
If you are installing a DSSI VAXcluster configuration, and you are a licensed
self-maintenance customer, you should be familiar with the contents of your DSSI
VAXcluster Installation and Troubleshooting manual.
Caution
If you are installing a DSSI configuration, to prevent system performance
degradation or data corruption caused by excessive ground offset voltages,
make sure your site power distribution system does not have any of the
grounding faults listed in your Site Preparation manual.
The installation instructions that follow assume:
• Your site meets all the requirements listed in the system Site Preparation
manual.
• All cables that you plan to connect to your system are in place and clearly
labeled.
Terminal data cables?
Telephone cables?
Network cables?
• You have the following tools (not included in your shipment).
Scissors
Flat-blade screwdriver
Phillips (cross-point) screwdriver
Adjustable wrench
Voltmeter calibrated for millivolts
1

2 Check the Shipment
1. Find the Product Delivery Document. It is inside or attached to one of the
shipping cartons.
Product Delivery Document
TMTM
Digital Equipment Corporation
Documentation Issue Date
Customer Order No. Dec No. Product Delivery No.
Shipped To Invoice To
MLO-007108
2

2. Make sure your shipment is complete by checking that each item listed as
shipped on the Product Delivery Document appears on a Content Listing or
on a Barcode Label on the outside of one of the cartons in your shipment.
Content Listing
TMTM
Date:
DEC NO.
Line
Item Model No.
Shipped Description Serial No. Rev Qty
681QJ-B9 A01 AY0121DS23
MLO-010176
AContent Listing may also be attached to a smaller container (bag or box)
packed inside a shipping carton.
3

3. Use the unpacking illustrations on the cartons as a guide to unpack your
shipment.
Warning
The system weighs 68 kilograms (150 pounds) with all options installed.
To prevent personal injury, two or more people should move the system.
Anti Static Anti Static
System
Keys to Front Door
Note:
Unpacking is illustrated on the
exterior of the shipping carton.
Ground Wire Cable
Power Cable
Console Terminal Cable
(12-13756-A8)
(17-01364-02)
DSSI Bus Node ID Plugs
(12-28766-19)
KZQSA
Internal Cable
(BC06P-2F)
KZQSA
Bus Node ID Plugs
(12-28766-28)
Installation
Checklist
MLO-007181
Customer
Hardware
Information Kit
Installation Checklist
VMS FIS Guide
Includes:
4. Check the contents of each carton against the Content Listing to ensure you
received all items.
4

5. If any item is missing or damaged:
Contact your delivery agent.
Contact your Digital sales representative.
3 Position the System
Warning
To prevent personal injury, do not use the handholds to lift the system.
Slides Front
to Back
Rolls Left to Right MLO-004012
Hand Holds
For now, leave space behind the system for routing cables.
5

4 Open the System Doors
1. Find a key (two are provided).
Anti Static
MLO-007110
2. Insert that key in the rotary lock, and turn it to the bottom position.
Door Handle
Rotary Lock
MLO-007111
6