Digital Equipment VAXstation VLC Quick start guide

Upgrade Instructions
Order Number: EK–VSAXP–UP. A01
VAXstation VLC to
DEC 3000 Model
300/300L AXP
MLO-010693

Can Cannot
Upgrade Upgrade
Expansion SZ03
Boxes: SZ12
SZ16
Hard Disks: RZ23L RZ57
RZ24L
RZ24*
RZ25*
RZ26*
RZ55*
RZ56*
RZ58*
Removable TZK10 RX23
Media:* TZ30 RX33
TLZ04
TLZ06
RRD42
RX26
Memory
Option: None
* Available only in expansion boxes
Options You Can Upgrade

Can Cannot
Upgrade Upgrade
Monitors VRC16-Cx/Hx VR262-Ax
VRM17-Ax/Hx VR290-Dx
VR319-Dx** VR297-Dx
VR320-Dx** VR299-Dx
VRT16-Hx** VRT16-Dx
VRT19-Hx** VRT19-Dx
VRT13
VR319-Cx
VR320-Cx
Input
Devices: VSxxx-AB
VSxxx-AA
VSxxx-FA
VSxxx-JA
VSxxx-GA
LK401
LK201
Ethernet
Adapter: DECXM-AA
** Available only on the Model 300.
Options You Can Upgrade

Check the Box Contents
Monitor
Video Cable
Antistatic
Wrist Strap
Mousepad
Monitor
Power Cord
System Power
Cord
Screwdriver
System Unit
Documentation
Modem Loopback
Connector
10BASE-T Loopback
Connector
SCSI
Terminator
Universal
Strain Relief
Strap
Keyboard/Mouse
Extension Cable
System Kit:
Network
Cable
Accessory Kit:
MLO-010694
Screws (8)
Mounting
Brackets (2)
xxxxxxx
xxxxxxxxxxx
xxx
Upgrade
Card
Return
Address
Label External
SCSI Cable

If your DEC 3000 system has factory-
installed drives, check the SCSI ID settings
on the drives you are upgrading.
To find out the SCSI ID settings on your
VAXstation drives, enter these commands:
•To shut down your system software:
$ SYS$SYSTEM:SHUTDOWN
•To show the drives and their SCSI ID
settings: >> SHOW CONFIG
A screen similar to this will display:
Write your system drive names and SCSI ID
settings here:
Check the SCSI ID Settings
>>> SHOW CONFIG
KA48-A V1.3-343-V4.0
08-00-2B-1D-28-6C
8MB
DEVNBR DEVNAM INFO
------ ------ --------------------------------
1 NVR OK
LR - 8 PLN FB - 5.2
3 DZ OK
4 CACHE OK
8MB = S0/1=0MB, S2/3=0MB, S4/5=0MB
6 FPU OK
7 IT OK
8 SYS OK
9 NI OK
10 SCSI OK
5-RX26 6-INITR
11 AUD OK
>>>
2 LCG OK
5 MEM OK
MLO-010730
SCSI
ID Numbers

1. Turn off the VAXstation system unit by
pressing O on the On/Off switch.
Caution: After you turn off the system,
wait 15 seconds before
unplugging the power cord.
2. Unplug all the cables.
3. To open the cover, press firmly on
the latches located on the side of the
system unit.
•Push the latches in and up until the cover
releases.
•Pull the cover up and off.
Caution: You may damage the equipment
if you do not wear an antistatic
wrist strap when working inside
the system unit.
Turn Off/Open the VAXstation
C1
C2
MLO-010695
Latches

Your VAXstation may have an RZ23L or an
RZ24L fixed disk drive installed.
4. Locate the small metal clip attached to
the disk mounting bracket.
•Push in on the metal clip to unlock the
bracket, then slide the drive away from
the power supply.
•Remove the drive from the system unit.
•Disconnect the SCSI and power cable
connectors from the drive.
5. Remove the drive bracket and clip by
using a Phillips screwdriver to remove
the rubber feet.
Remove/Prepare the Disk Drive
C1
C2
MLO-010696
Power
Supply

You need change a SCSI ID setting only if
two or more drives have the same setting.
Check the SCSI ID setting for the VAXsta-
tion drives, which you noted previously. If
you need to change a SCSI ID on a drive
that is not covered here, see the DEC 3000
Model 300/300L AXP System Hardware
Reference Guide.
RZ23L Drive SCSI ID Settings:
Set the SCSI ID on the Drives
MLO-010587
6
SCSI
Settings:
5
4
3
2
1
0
E2 E1
E3

RZ24L Drive SCSI ID Settings:
Set the SCSI ID on the Drives
MLO-010732
4
SCSI
Settings:
5
6
0
1
2
3
A0 A1 A2

If you are upgrading an RZ23L or RZ24L
drive from a VLC to a DEC 3000 300/300L,
you must put the drive into either of the
brackets included in your accessory kit.
•Stand the bracket on its side with the
sliding latch up. Place the drive in the
bracket with the connectors facing you,
as shown below.
•Attach the two screws on each side of
the drive bracket.
Insert a Drive Into a Bracket
MLO-010844