Digital Equipment 5200 Series User manual

DIGITAL Server 5100/5200
DIGITAL Server 5100/5200 Series
Service Maintenance Manual
Part Number: ER-B52WW-SM. A01
Digital Equipment Corporation

January 1998
The information in this document is subject to change without notice and should not
be construed as a commitment by Digital Equipment Corporation.
Digital Equipment Corporation assumes no responsibility for any errors that might
appear in this document.
The software, if any, described in this document is furnished under a license and may
be used or copied only in accordance with the terms of such license. No responsibility
is assumed for the use or reliability of software or equipment that is not supplied by
Digital Equipment Corporation or its affiliated companies.
Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject
to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data
and Computer Software clause at DFARS 252.227-7013.
DIGITAL Server 5100/5200 Series Service Maintenance Manual
1998 Digital Equipment Corporation.
All Rights Reserved.
DEC, DIGITAL, ServerWORKS, and the DIGITAL logo are trademarks of Digital
Equipment Corporation.
Intel and Pentium are registered trademarks of Intel Corporation.
Microsoft, Windows NT, and Windows 95 are registered trademarks of Microsoft
Corporation.
Novell and NetWare are U.S. registered trademarks of Novell Inc.
OS/2 and PS/2 are registered trademarks of International Business Machines
Corporation.
PhoenixBIOS is a trademark of Phoenix Technologies Ltd.
SCO is a trademark of The Santa Cruz Operation, Inc.
SCSI
Select is a registered trademark of Adaptec Corporation.
UNIX is a registered trademark of X/Open Company, Ltd.
All other trademarks and registered trademarks are the property of their respective
holders.

DIGITAL Server 5100/5200
FCC ID: B5XWW1
The FCC wants you to know...
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user's authority
to operate this equipment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
All external cables connecting to this basic unit need to be shielded. For cables
connecting to option cards, see the option manual or installation instructions.
This digital apparatus does not exceed the Class B limits for radio noise emissions
set out in the radio interference regulations of the Canadian Department of
Communications.

This equipment is in the 2nd Class category (information equipment to be used in a
residential area or an adjacent area thereto) and conforms to the standards set by
the Voluntary Control Council For Interference by Data Processing Equipment and
Electronic Office Machines aimed at preventing radio interference in such residential
area.
When used near a radio or TV receiver, it may become the cause of radio
interference.
Read the instructions for correct handling.
This equipment meets or exceeds requirements for safety in the U.S. (UL 1950),
Canada (CSA C22.2 No. 950), and Europe (EN 60950/IEC 950) with Nordic
requirements.
This equipment meets or exceeds the ergonomic requirements of ZH1/618 and is
certified to bear the GS mark by TUV Rheinland of Germany.
This equipment has been tested for radio frequency emissions and has been verified
to meet VDE 0871 Class B.

i
DIGITAL Server 5100/5200
Contents
Preface.............................................................................................................. vii
1
Product Description
Introduction..................................................................................................... 1-1
Reliability/Availability................................................................................. 1-1
Server Expansion..................................................................................... 1-2
Server Management and Security............................................................. 1-3
Server Configurations...................................................................................... 1-4
Server Naming Guidelines........................................................................ 1-4
Product Model Numbering Convention...................................................... 1-5
Related Material.............................................................................................. 1-7
Latest Product Information and Updates.......................................................... 1-9
Application Server Product Information..................................................... 1-9
Updates.................................................................................................... 1-10
2
Server Software and Utilities
Introduction..................................................................................................... 2-1
ServerWORKS Quick Launch.......................................................................... 2-2
Creating Diskettes and Viewing On-line Documentation............................ 2-2
System Configuration Utility (SCU) .................................................................. 2-2
When to Run the SCU.............................................................................. 2-3
Configuring Expansion Boards.................................................................. 2-4
Starting the SCU ...................................................................................... 2-5
Using the SCU.......................................................................................... 2-7
SCU Keyboard Function Keys................................................................... 2-8
Configure Computer................................................................................. 2-9
Setting the Date and Time........................................................................ 2-9
Maintain System Configuration Diskette.................................................... 2-10

Contents
ii
RAID Configuration Utility................................................................................ 2-11
BIOS Upgrade Utility ....................................................................................... 2-11
SCSI
Select Utility ............................................................................................ 2-12
Diagnostics ..................................................................................................... 2-13
3
SCU Features
Introduction..................................................................................................... 3-1
System - DIGITAL Server 5100/5200........................................................ 3-2
System Management Group..................................................................... 3-3
Diskette Drive Group................................................................................ 3-4
Boot Options Group.................................................................................. 3-5
Integrated Peripherals Group.................................................................... 3-6
Keyboard Features Group ........................................................................ 3-8
Shadow Options Group ............................................................................ 3-9
Security Options Group ............................................................................ 3-10
Cache Options Group............................................................................... 3-11
Advanced Control Group .......................................................................... 3-11
EISA or PCI Devices Group...................................................................... 3-12
4
Troubleshooting
Introduction..................................................................................................... 4-1
Initial Troubleshooting...................................................................................... 4-2
Diagnostics ..................................................................................................... 4-2
Running the Diagnostics........................................................................... 4-3
Running Quick Tests or Groups of Tests................................................... 4-3
Running DIGITAL Vendor Extended Tests................................................ 4-4
Running Diagnostics Tests from the Hard Disk Drive................................. 4-4
Obtaining Information about the Server ........................................................... 4-5
Obtaining Information Using the SCU........................................................ 4-7
Obtaining Information Using Server Management Software....................... 4-7
Displaying Server Status Using the Hardware........................................... 4-8
Server Status Messages........................................................................... 4-9
POST OCP Messages..................................................................................... 4-11
POST/Boot Codes.................................................................................... 4-11
OCP Messages............................................................................................... 4-14
OCP Status and Error Messages.............................................................. 4-15
Server CPU Voltage and Temperature Ranges for Pentium Pro....................... 4-17
CPU Voltage Range ................................................................................. 4-17
VRM Voltage Range................................................................................. 4-17

Contents
iii
DIGITAL Server 5100/5200
Server CPU Voltage and Temerature Ranges for Pentium II............................ 4-18
CPU Voltage Range ................................................................................. 4-18
CPU VRM Range ..................................................................................... 4-19
Advanced Troubleshooting.............................................................................. 4-20
Server Troubleshooting ................................................................................... 4-21
Disk Drive Troubleshooting.............................................................................. 4-24
SBB Troubleshooting....................................................................................... 4-27
Tape Drive Troubleshooting............................................................................. 4-27
Monitor Troubleshooting.................................................................................. 4-28
CD-ROM Troubleshooting ............................................................................... 4-29
Diskette Drive Troubleshooting........................................................................ 4-30
RAID Troubleshooting ..................................................................................... 4-31
5
FRU Replacement
Introduction..................................................................................................... 5-1
Server Front View............................................................................................ 5-2
Server Left-Side View (Pentium Pro Processor)............................................... 5-4
Server Left-Side View (Pentium II Processor).................................................. 5-6
Server Right-Side/Rear View........................................................................... 5-8
Miscellaneous ................................................................................................. 5-10
Labels and Nameplates................................................................................... 5-11
Service Procedures......................................................................................... 5-11
Recommended Tools................................................................................ 5-11
BIOS Version Information......................................................................... 5-11
Disconnecting External Devices and Power ..................................................... 5-12
Removing the Side Panels.............................................................................. 5-13
Server Front View..................................................................................... 5-15
Server Left Side View............................................................................... 5-17
Server Right Side View............................................................................. 5-19
Server Rear View ..................................................................................... 5-21
Main Logic Board Connectors................................................................... 5-23
Main Logic Board Components................................................................. 5-25
Pentium Pro Processor Module Components and Connectors................... 5-26
Pentium II Processor Module Components ............................................... 5-27
Ethernet Daughter Card Components and Connectors.............................. 5-28
Jumpers and Switch Settings.................................................................... 5-29
Pentium Pro Processor Module Switch Settings........................................ 5-32
Pentium II Processor Module Switch Settings ........................................... 5-34
Processor Clock Speed Switch Settings.................................................... 5-34
Installing Additional SIMM Memory.................................................................. 5-37

Contents
iv
Server SIMMs Requirements.................................................................... 5-37
Memory Configuration Guidelines............................................................. 5-38
Upgrading Memory................................................................................... 5-39
Memory Troubleshooting.......................................................................... 5-39
Installing Additional DIMM Memory.................................................................. 5-40
Memory Configuration Guidelines............................................................. 5-41
Memory Configurations............................................................................. 5-42
Memory Troubleshooting.......................................................................... 5-43
Removing and Replacing the Power Supply..................................................... 5-44
Removing and Replacing the Diskette Drive..................................................... 5-46
Removing and Replacing the CD-ROM Drive................................................... 5-48
Removing and Replacing a Cooling Fan .......................................................... 5-50
Removing and Replacing the Secondary Cooling Fan 2.................................. 5-52
Removing and Replacing Cooling Fan 5 .......................................................... 5-54
Removing and Replacing the Speaker............................................................. 5-56
Removing and Replacing the Main Logic Board............................................... 5-58
Removing and Replacing the Server Battery/Real Time Clock (RTC) ............... 5-60
Removing and Replacing the Storage Backplane............................................. 5-62
Removing and Replacing a Caster................................................................... 5-64
6
Processor Module Upgrades
Introduction..................................................................................................... 6-1
Processor Compatibility in a Multiprocessor Environment.......................... 6-1
Boot the Quick Launch CD-ROM and Create Diskettes............................. 6-2
Upgrade the BIOS........................................................................................... 6-2
Update the BIOS...................................................................................... 6-3
Pentium Pro Processor Upgrades.................................................................... 6-4
Configuration Guidelines........................................................................... 6-4
Installing a Processor ............................................................................... 6-5
Pentium II Processor Upgrades....................................................................... 6-13
Processor Module Configuration Guidelines.............................................. 6-13
Processor Configurations.......................................................................... 6-14
Upgrading to a Dual Processor Configuration............................................ 6-15
System Identification (ID) Configuration Utility.................................................. 6-20
Run the System ID Configuration Utility .................................................... 6-21
Run the SCU................................................................................................... 6-22
Troubleshooting............................................................................................... 6-23
Using the Crisis Recovery Diskette if Necessary....................................... 6-23

Contents
v
DIGITAL Server 5100/5200
7
Device Mapping
Introduction..................................................................................................... 7-1
Processor Memory Address Map.............................................................. 7-2
I/O Address Map...................................................................................... 7-3
Server Interrupt Levels............................................................................. 7-4
PCI Configuration Space Address Map..................................................... 7-4
A
Service Notes................................................................................................ A-1
Figures
Typical DIGITAL Server 5100/5200 ................................................................................... viii
2-1. SCU Main Menu Options........................................................................................... 2-6
4-1. DIGITAL Server Component Information.................................................................... 4-6
5-1. Server Front View...................................................................................................... 5-3
5-2. Server Left-Side View (Pentium Pro Processor)........................................................ 5-5
5-2. Server Left-Side View (Pentium II Processor)............................................................ 5-7
5-3. Server Right-Side/Rear View..................................................................................... 5-9
5-4. Server Brake..............................................................................................................5-12
5-5. Unlocking and Removing the Side Panels................................................................. 5-14
5-6. Server Front View...................................................................................................... 5-16
5-7. Server Left Side View................................................................................................. 5-18
5-8. Server Right Side View.............................................................................................. 5-20
5-9. Server Rear View....................................................................................................... 5-22
5-10. Main Logic Board Connectors.................................................................................. 5-24
5-11. Main Logic Board Components................................................................................ 5-25
5-12. Pentium Pro Processor Module Components and Connectors ............................... 5-26
5-13. Pentium II Processor Module Component Locations................................................ 5-27
5-14. Ethernet Daughter Card Components and Connectors........................................... 5-28
5-15. Main Logic Board Switch and Jumper Locations ...................................................... 5-31
5-16. Pentium Pro Processor Module Switch Locations .................................................... 5-33
5-17. Pentium II Processor Module Switch Settings ......................................................... 5-36
5-18. Processor Module SIMM Bank Locations................................................................. 5-38
5-19. DIMM Socket Locations........................................................................................... 5-41
5-20. Removing and Replacing the Power Supply............................................................ 5-45
5-21. Removing and Replacing the Diskette Drive............................................................ 5-47

Contents
vi
5-22. Removing and Replacing the CD-ROM Drive.......................................................... 5-49
5-23. Removing and Replacing a Cooling Fan.................................................................. 5-51
5-24. Removing and Replacing the Secondary Cooling Fan 2........................................... 5-53
5-25. Removing and Replacing Cooling Fan 5................................................................... 5-55
5-26. Removing and Replacing the Speaker...................................................................... 5-57
5-27. Removing and Replacing the Main Logic Board....................................................... 5-59
5-28. Replacing the Server Battery/RTC........................................................................... 5-61
5-29. Removing and Replacing the Storage Backplane..................................................... 5-63
5-30. Removing and Replacing a Caster ........................................................................... 5-65
6-1. Removing the Processor Module............................................................................... 6-5
6-2. Removing the Retaining Clip...................................................................................... 6-6
6-3. Removing the Processor/Heat Sink Assembly........................................................... 6-7
6-4. Installing the New Processor...................................................................................... 6-8
6-5. Installing the Retaining Clip........................................................................................ 6-9
6-6. Installing a VRM......................................................................................................... 6-10
6-7. Installing the Processor Module................................................................................. 6-11
6-8. Processor Module Slot Location ................................................................................. 6-14
6-9. Removing the Processor Module............................................................................... 6-15
6-10. Removing the Terminator Module........................................................................... 6-16
6-11. Installing the Second Processor............................................................................... 6-17
6-12. Installing a VRM...................................................................................................... 6-18
6-13. Installing the Processor Module............................................................................... 6-19

vii
DIGITAL Server 5100/5200
Preface P
This
Service Maintenance Manual
is a troubleshooting guide that can be used for
reference when servicing DIGITAL Servers.
DIGITAL reserves the right to make changes to this
Service Maintenance Manual
without notice. Accordingly, the illustrations and procedures in this document might
not apply to all DIGITAL Servers to be serviced since many of the diagnostic tests
are designed to test more than one product.
CAUTION: DIGITAL recommends that only A+/DIGITAL
Server certified engineers attempt to repair this equipment.
All troubleshooting and repair procedures are detailed to
support subassembly/module level exchange. Because of the
complexity of the individual boards and subassemblies, no
one should attempt to make repairs at the component level or
make modifications to any printed circuit board. Improper
repairs can create a safety hazard. Any indications of
component replacement or circuit board modifications might
void any warranty or exchange allowances.

Preface
viii
DEC00421
Typical DIGITAL Server 5100/5200

1-1
DIGITAL Server 5100/5200
1
Product Description 1
Introduction
The DIGITAL Server 5100/5200 is a high-performance, highly-scaleable network and
application server featuring the latest in modular processor, and storage technology.
The DIGITAL Server provides support for the following features:
Reliability/Availability
Pentium Pro or Pentium
II Processor Module
Pentium Pro processor module. Each Pentium Pro
processor operates using either 36-bit SIMMs, 60 ns
access time, EDO or Fast Page memory.
Or
Pentium II processor module. Each Pentium II processor
operates using 168-pin, 72-bit DIMMs, 60 ns access time
EDO memory, ECC protected.
Error Correction Code
(ECC) Memory
Recovery from single-bit cache and memory errors.
Dual-Channel Storage
Backplane
Redundant disk subsystems using integrated SCSI
controllers or expansion storage controllers.
continued

Product Description
1-2
Power Supply
The DIGITAL Server ships with one power supply for
normal operation. An optional second power supply can be
purchased to provide redundant power.
Variable Fan Speed
Automatically adjusts fan speed according to ambient
temperature.
Internal Sensors
Monitors internal server temperatures, fan operation, and
power supply temperatures and voltages.
Clusters
Supports DIGITAL Clusters for Windows NT for database
and file services failover.
Server Expansion
Flexible Memory
Architecture
ECC memory supported. Server memory can be
upgraded to a maximum of 1 GB using SIMM memory on
a Pentium Pro processor module. For Pentium II
processor modules, you can upgrade to a maximum of
512 MB using DIMM memory.
Five EISA Expansion
Slots and Six PCI
Expansion Slots
Accommodates industry-standard expansion boards such
as network, Small Computer System Interface (SCSI),
Redundant Array of Integrated Disks (RAID), and
modems.
Integrated SVGA Video
Controller
Supports management and configuration applications
locally (on the main logic board) without use of an
expansion slot.
Two Integrated SCSI
Controllers
Support for narrow, fast wide, and wide Ultra external and
internal SCSI devices. Wide Ultra configurations require
optional wide Ultra SCSI bus repeaters. Contact an
authorized DIGITAL sales representation for more
information.
continued

Product Description
1-3
DIGITAL Server 5100/5200
Capacity for 10 Internal
SCSI Storage Devices
Accommodates one CD-ROM drive (standard), seven
3½-inch half-height drives in Storage Building Blocks
(SBBs), and two narrow (50-pin) half-height, 5¼-inch
devices; or one full-height, 5¼-inch device (CD-ROMs or
tape drives).
External I/O Ports
Two serial ports and one parallel port to support external
options such as a printer, modem, or local terminal.
Wide SCSI Storage
Backplane
Supports high-performance drives.
Disk Hot Swap Capability
Allows replacement of SBB disk drives while the server is
operating.
Integrated Network
Controller/External
Network Ports
A DIGITAL Ethernet controller on the main logic board.
An Ethernet daughter card provides: one 10/100Base-T
(10/100 Mb/s) port, one 10Base-2 (10 Mb/s) port, and one
10Base-5 (AUI) port.
Server Management and Security
Server Diagnostics
Allows local and remote diagnosis of server problems.
Hardware Configuration
Allows local and remote server configuration.
Unique Asset
Management
Unique server identifier in non-volatile memory provides
easy asset management.
Firmware Upgrade Utility
Upgrades firmware versions.
Operator Control Panel
(OCP)
Back-lit, 16-character display for diagnostic and error
messages.
Hard Drive Indicator
Lights
Provides immediate status information on SBB hard drive
activity or failure.
Key Lock
Limits access to the server’s internal components.
Interlock Sensor
Switches
Automatically turns off server power if either side panel is
removed when the server power is on.

Product Description
1-4
Server Configurations
The following rules apply when Product Family Names and Product Model Names
are assigned to DIGITAL Server products. These rules apply to all products
developed in the NT Server Business Unit (NTSBU).
Server Naming Guidelines
• All products in a family carry the same name on the nameplate. (i.e. all
products in the Entry space will carry the name DIGITAL SERVER 1000)
Family Name Segment
DIGITAL SERVER 500 SUB ENTRY
DIGITAL SERVER 1000 ENTRY
DIGITAL SERVER 3000 DEPARTMENT
DIGITAL SERVER 5000 APPLICATION
DIGITAL SERVER 7000 ENTERPRISE
DIGITAL SERVER 9000 SUPER ENTERPRISE
• Products in a rackmount chassis will have an R after the Family Name
(DIGITAL Server 3000R).
• Product models within a family will be differentiated by the Product Model
Name. The Product Model Name will appear on a label on the rear of the
product. Specific configurations within a model will carry the same Product
Model Name and will be differentiated by the part number.

Product Description
1-5
DIGITAL Server 5100/5200
Product Model Numbering Convention
The following example describes the product model numbering convention:
DIGITAL SERVER 1234 5678A R
1 = PRODUCT FAMILY NAME (first character of family number)
2 = MAJOR PROCESSOR TECHNOLOGY DIFFERENTIATOR WITHIN THE
FAMILY
This number will be assigned to each new platform based on the following matrix.
Open numbers will be assigned as new processor technology is introduced. THIS
FIELD IS NOT USED FOR SUB ENTRY PRODUCTS.
100 = Pentium Pro
200 = Pentium II – Slot 1
300 = EV5
400 = Pentium II – Slot 2
500 = EV6
600 = OPEN
700 = OPEN
800 = OPEN
900 = OPEN
3,4 = USED TO DIFFERENTIATE MODELS BASED UPON DIFFERENT
PROCESSORS WITHIN A PROCESSOR TECHNOLOGY (I.E. CLOCK SPEED,
CACHE SIZE) START AT 00 FOR FIRST MODEL AND INCREMENT BY 05 FOR
EACH ADDITIONAL MODEL.

Product Description
1-6
5 = CPU TYPE
BLANK = PENTIUM
1= PENTIUM PRO
2 = PENTIUM II/SLOT 1
3 = PENTIUM II/SLOT 2
4 = Open/Available for future processors
5 = Open/Available for future processors
6 = ALPHA EV56
7 = ALPHA PCA57
8 = ALPHA EV6
9 = ALPHA EV67
6, 7, 8,9 = CPU CLOCK SPEED IN MHZ
A = CPU VENDOR
INTEL = BLANK
ALPHA = A
AMD = K
R = CHASSIS TYPE
BLANK = STANDARD CHASSIS
R = RACKMOUNT CHASSIS

Product Description
1-7
DIGITAL Server 5100/5200
Related Material
The following related material is available:
Document or Software Title Order Number Description
Service Quick Reference ER-B52WW-SR (English only) Provides troubleshooting information
that can be used when servicing
DIGITAL servers. This manual is a
condensed version of the Service
Maintenance Manual and is provided
in a pocket-size format (4 x 8-
inches).
Installation Guide ER-B52WW-IM
(Multilanguage)*
ER-B52WW-IJ (Japanese)
Provides information on connecting
hardware cables and booting the
server. This guide also explains how
to use DIGITAL ServerWORKS
Quick Launch to install an operating
system, create driver and utility
diskettes, and view on-line help and
support documentation.
System Reference ER-B52WW-UA (English)
ER-B52WW-UJ (Japanese)
Provides information on using the
server’s configuration utilities,
installing peripherals and options,
security, and troubleshooting. The
System Reference is available on
the Quick Launch CD-ROM in
English, Spanish, German, Italian,
and French.
Quick Reference labels 36-45369-07 (left side panel)
36-45369-08 (right side panel) Provides an overview of major server
components, configuration guidelines,
and SCSI cabling information. These
labels are located on the inside of the
server’s side panels.
Warranty and Service Information ER-PCWAR-CM
(Multilanguage)* Provides warranty information and a listing of phone numbers for
technical support.
Ultra SCSI Bus Repeater Module
Installation Guide ER-SBRAA-IA Describes installation procedures for an Ultra SCSI Bus Repeater Module
and configuring Ultra SCSI drives.
* Multilanguage includes: English, French, Italian, German, and Spanish
continued

Product Description
1-8
Document or Software Title Order Number Description
DIGITAL ServerWORKS software QB-4WY9A-SA
(Multilanguage)* Contains ServerWORKS Quick Launch and ServerWORKS
Manager software and
documentation.
Quick Launch consists of a bootable
CD-ROM disk and Getting Started
guide. This program steps the user
through the initial server setup and
operating system installation.
ServerWORKS Manager consists of
two CD-ROMs and an Overview and
Installation Guide and supporting
documentation.
Product README and Revision
History Information - Quick
Launch CD-ROM
Refer to the Quick Launch
CDROM in the DIGITAL
ServerWORKS software kit
Provides additional product
information and product change
history.
Option documentation - Quick
Launch CD-ROM Refer to the Quick Launch CDROM in the DIGITAL
ServerWORKS software kit
Provides postscript files that can be
viewed and printed using Adobe
Acrobat Reader software. These
files are provided in PDF format on
the Quick Launch CD-ROM
Diagnostic Software - Quick
Launch CD-ROM Refer to the Quick Launch CDROM in the DIGITAL
ServerWORKS software kit
Contains an advanced set of
diagnostic utilities for identifying and
correcting problems on the server.
The diagnostic software can be used
to verify proper hardware installation
and isolate intermittent problems that
are not detected by the Power On
Self Test (POST). Refer to chapter
2 for information on using the
diagnostic utilities.
PC Product Support Information
Kit QA-5RJAA-G8 (English only) Provides all the latest product documentation for all NTSBU mobile,
desktop, and server products.
* Multilanguage includes: English, French, Italian, German, and Spanish
NOTE: Refer to Chapter 2 for procedures on how to create
diskettes and view documentation from the Quick Launch
CDROM.