Digital Watchdog MegaPix DWC-MVT4WiA User manual

Default Login Information
Username: admin Password: admin
Quick Start Guide Quick Start Guide
WHAT’S IN THE BOX
Quick set up
guide 1Tapping screws PA 4x35 – 4pcs 1 Set
Mounting
template 1Plastic anchors – 4pcs 1 Set
Waterproof
cap 1 Set Allen wrench 1
Sponge 1
CVBS and
DC IN
cables
1
1. The mounting surface must bear three times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line
cover to be damaged. This may cause a breakdown or fire.
3. For the installation process, remove the camera’s dome cover by
loosening the screws at the base of the dome.
4. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.
6. To use the camera’s water proof wiring:
a. Install the LAN cable into .
b. will be assembled to with a 1/4 turn.
c. Thread tightly to .
7. Secure the camera to the mounting surface with the provided screws.
8. Adjust the camera to obtain an optimum angle by using the camera’s
three axis gimbal. The camera’s max angles are:
Pan: 0°~ 360°
Tilt: 0°~ 77°
Rotation: 0°~ 360°
9. Remove the protection film softly to complete the installation.
5. Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect
the camera using an Ethernet cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 3 – INSTALLING THE CAMERA
STEP 2 – CABLING THE CAMERA TO EXTERNAL
DEVICES
a
a
b
b
c
NOTE: To ensure moisture seal, make sure the o-ring is in place
between
and . In extreme environments use of an outdoor
rated sealer is recommended.
ab
NOTE: When using the waterproof cap, crimp the RJ45 connector
after passing the cable through the waterproof cap.
Power requirements Power consumption
DC 12V
POE IEEE 802.3af Max. 5W
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search your product by entering the part number in the ‘Search by Product’
search bar. Results for applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals, Quick Start
Guides (QSG), software and firmware will appear in the results.
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for initial
set up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
DWC-MVT4WiA
NOTE: If the PoE network switch is used to connect the camera,
DC12V power supply is not required.
Power
Ethernet
Cable
Ethernet
Cable
5a
5b
6
a
b
c
Temp late
Sheet
Sponge
Reset
Button
1
2
7
3
4
8
Tilt: 0° ~ 77°
Pan: 0° ~ 360°
Rotation: 0° ~ 360°

7. To view the camera’s web viewer, click on ‘View Camera Website’.
8. To save the changes made to the camera’s settings, input the ID and
PW of the camera for authentication and click ‘Save’.
9. If the camera needs to be rebooted after the settings were changed,
press the ‘Reboot’ button. The camera will cycle power and will
appear back in the search results once the reboot is complete.
6. The camera’s default network information is:
STEP 5 – DW IP FINDER™
STEP 4 – MANAGING THE MICRO SD CARD
Use the DW IP Finder™software to scan the network and detect all
MEGApix®cameras, set the camera’s network settings or access the
camera’s web client.
Rev Date: 09/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Select DHCP if the internet service is dynamic IP. This will allow the camera
to receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask,
Gateway and DNS information.
Contact your network administrator for more information.
Default TCP/IP information
• IP: DHCP
‘Port Forwarding’ has to be set in your network’s router for external
access to the camera.
Default ID / PW : admin / admin
Network Setup
1. Go to: http://www.digital-watchdog.com
2. Search for ‘IP Finder’ on the quick search bar at the top of the page.
3. The latest IP Finder software will appear in the search results. Click on
the link to download the file to your computer.
1. To install the camera’s SD Card, locate the TF / micro SD card slot
in the camera’s board by removing the camera’s bubble dome. See
image below.
2. Insert a micro SD card into the micro SD card slot by pressing the
micro SD card.
3. To remove the micro SD Card, press the card inward to release from
the card slot.
4. The software will scan your network for all supported cameras and
display the results in the table. Allow up to 5 seconds for the IP Finder
to find the camera on the network.
5. Select a camera from the list by double-clicking on the camera’s
image or clicking on the ‘Click’ button under the IP Conf. column. The
camera’s network information will appear. If necessary, you can adjust
the camera’s network type.
Quick Start Guide
STEP 6 – WEB VIEWER
NOTE: Some Menu options may not be available based on the
camera model. See the full manual for more information.
*
NOTE: This camera’s web client must be accessed via Internet
Explorer web browser only.
The GUI display may dier by camera models.
Once the camera’s network settings have been setup properly, you can
access the camera’s web viewer using the DW IP Finder™.
To open the camera’s web viewer:
1. Find the camera using the DW IP Finder™.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer will
open up in your default web browser.
4. Enter the camera’s username and password (default are admin /
admin).
5. If you are accessing the camera for the first time, install the
ActiveX player for web files in order to view video from the
camera.
*
TF / Micro SD Card
Slot
Search for Devices
Device’s
Network Settings
Devices Firmware Version
Select which
Network to Scan
Camera’s Live
Thumbnail View
Show/Hide Thumbnail View
Filter Search Results
Device Name,
Model, IP Address,
and MAC Address
Firmware Upgrade
NOTE: For security purposes, it is highly recommended to
change the cameras default password.
*