Digitus DN 16058 User manual

ADVANCED NETWORK
SURVEILLANCE DOME CAMERA
User Manual
Please read instructions thoroughly before operation and retain it for future reference.

IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the
European law on the Restriction of Hazardous Substances (RoHS) directive, which means
our manufacture processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product
must be collected separately at the product end-of-life. This applies to your product and
any peripherals marked with this symbol. Do not dispose of these products as unsorted
municipal waste. Contact your local dealer for procedures for recycling this equipment.
Disclaimer
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or
assume any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The
content of this manual is subject to change without notice.
Grounding
This is a Safety Class 1 Product (provided with a protective earthing ground incorporated in the power
cord). The mains plug shall only be inserted in a socket outlet provided with a protective earth contact. Any
interruption of the protective conductor inside or outside of the instrument is likely to make the instrument
dangerous. Intentional interruption is prohibited.
Water & Moisture
Do not expose this product to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the product.
Trademark Acknowledgements
Internet Explorer, Microsoft, Windows, Mozilla & QuickTime are registered trademarks of the respective
holders.
MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR
THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING
MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY
MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL
AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which
are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public
License (“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the
copyright of the corresponding author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new
commands, and some tools to get you into the code. The codes are provided on the FTP
site, and please download them from the following site or you can refer to your distributor:
Version
Firmware: 1053-1015-1021-1005-C504
Video Viewer Software: 0156

TABLE OF CONTENTS
1. OVERVIEW......................................................................................................................................... 1
1.1 Product Features....................................................................................................................................... 1
1.2 Package Content....................................................................................................................................... 1
1.3 Dimensions ............................................................................................................................................... 1
1.4 Cable Overview......................................................................................................................................... 1
2. BEFORE USING YOUR NETWORK CAMERA .................................................................................. 2
3. ACCESSING THE CAMERA VIA VIDEO VIEWER ............................................................................. 3
3.1 Accessing the camera ............................................................................................................................... 3
3.2 Control panel overview.............................................................................................................................. 3
3.2.1 Simplified Version (Default)..............................................................................................................................3
3.2.2 Full Function Version........................................................................................................................................4
3.2.3 Main Button Overview ......................................................................................................................................4
3.3 Frequently-used functions......................................................................................................................... 5
3.3.1 Record..............................................................................................................................................................5
3.3.2 Playback...........................................................................................................................................................5
3.3.3 Firmware Upgrade ...........................................................................................................................................6
3.3.4 E-Map...............................................................................................................................................................6
3.3.5 Smart Zoom....................................................................................................................................................10
4. SYSTEM CONFIGURATION .............................................................................................................11
4.1 General ................................................................................................................................................... 12
4.1.1 Log .................................................................................................................................................................12
4.1.2 Account...........................................................................................................................................................12
4.1.3 OnLineUser ....................................................................................................................................................14
4.1.4 Trigger ............................................................................................................................................................14
4.2 Network ................................................................................................................................................... 15
4.2.1 QoS ................................................................................................................................................................15
4.2.2 DDNS .............................................................................................................................................................15
4.2.3 SNTP..............................................................................................................................................................16
4.2.4 FTP.................................................................................................................................................................16
4.2.5 MAIL ...............................................................................................................................................................16
4.2.6 SMS................................................................................................................................................................17
4.2.7 Filter ...............................................................................................................................................................18
4.2.8 UPnP ..............................................................................................................................................................18
4.3 Video ....................................................................................................................................................... 19
4.4 Camera ................................................................................................................................................... 19
4.4.1 System ...........................................................................................................................................................20
4.4.2 Color...............................................................................................................................................................20
4.4.3 Time................................................................................................................................................................21
5. ACCESSING THE CAMERA VIA YOUR WEB BROWSER .............................................................. 22
5.1 Accessing the camera ............................................................................................................................. 22
5.2 Control panel overview............................................................................................................................ 23
5.2.1 Live View Panel..............................................................................................................................................23
5.2.2 System Configuration Panel...........................................................................................................................24
APPENDIX 1 PRODUCT SPECIFICATIONS........................................................................................ 26
APPENDIX 2 API ID APPLICATION FOR SMS MESSAGING.............................................................. 27

1
1. OVERVIEW
1.1 Product Features
Powerful mobile surveillance supporting iPhone, BlackBerry, Windows Mobile & Symbian
Smart Zoom: zoom in on the object that triggered the motion detection
Excellent low lux performance for dark environments
Low-latency video streaming with H.264 compression format
Motion detection and alarm notification functions
1.2 Package Content
□Network camera
□Installation Guide
□RJ45 cable extender adapter
□CD-ROM disc (including user manuals & CMS software “Video Viewer”)
1.3 Dimensions
Ø124.3
102
1.4 Cable Overview
CABLE DESCRIPTION
RJ45 network cable Connect it to the supplied RJ45 cable extender adapter for cable extension, and prepare
another RJ45 network cable with suitable length for your connection.
Reset wires Remove the insulating coating of these two wires, and twist them together to reset default. This
will reset all parameters, including the IP address to factory default settings.
Note: Disconnect power before twisting these two wires together, and connect to
power again for reset default.
Power cable Connect to DC12V power supply.
Note: The power adapter is optional.

2
2. BEFORE USING YOUR NETWORK CAMERA
Before using the network camera, make sure:
1) You have installed the supplied CMS software, “Video Viewer”.
2) You have configured the network settings, and the network connection is fine.
If not, please refer to your camera installation guide.
This network camera can be accessed via our supplied CMS software “Video Viewer”, the web
browser “Microsoft Internet Explorer” or “Mozilla Firefox”, and smart phones depending on different
using situations.
To check or configure up to 16 surveillance devices simultaneously with the record function, please use
“Video Viewer”.
For details about using Video Viewer, please refer to “3. ACCESSING THE CAMERA VIA VIDEO
VIEWER” at page 3, and “4. SYSTEM CONFIGURATION” at page 11.
To check or configure this network camera only, it’s recommended to use the web browser “Microsoft
Internet Explorer” or “Mozilla Firefox”.
For details about using the web browser, please refer to “5. ACCESSING THE CAMERA VIA YOUR
WEB BROWSER” at page 22.

3
3. ACCESSING THE CAMERA VIA VIDEO VIEWER
3.1 Accessing the camera
Step1:Double-click “ ” on your PC desktop to open Video Viewer. By defaults, the “Address
Book” panel will be displayed on the right side of the control panel.
Step2:Click “ ” to select the IP address of the camera you intend to connect, and double-click
it.
Step3:The live view is displayed in the Video Viewer.
3.2 Control panel overview
Two control panels are available and can be switched depending on your using habit.
3.2.1 Simplified Version (Default)

4
3.2.2 Full Function Version
3.2.3 Main Button Overview
Button Function Description
Simplified Full Function
Address Book Click to show the predefined IP address(es). You can add, remove or
search the IP address to log in the DVR remotely.
Miscellaneous
Control
Remote
Config
Click to go to the detailed system configuration.
For details, please refer to “4. SYSTEM
CONFIGURATION” at page 11.
Record
Setting
Click to go to the detailed record setting. For
details, please refer to “3.3.1 Record” at page 5.
Custom
Setting
Click to choose the language of this program, or
set the password when activating this program.
The changes will take effect when this program
is closed and executed again.
Log Click to view all event and recording logs, search the desired log(s) by
date, or playback the recording of the selected log.
/ / Record /
Record Stop
Click to start / stop the manual recording.
The record button will be disabled when the reserved disk capacity set in
“Record Setting” is larger than the current disk capacity. For details,
please refer to “3.3.1 Record” at page 5.
Snapshot Click to take a snapshot of the current view. The snapshot will be saved
in the path you specified in “Record Setting”.
Information Click to show the current network connection details.
PTZ Control Click to enter the PTZ control panel for the smart zoom function. For
details, please refer to “3.3.5 Smart Zoom’ at page 10.

5
3.3 Frequently-used functions
3.3.1 Record
To record remotely, click “ ” or “ ” →“ ” to go to the “Record Setting” page.
In the “Record Setting” page, you can set the following items:
‧Record type
‧Pre- / post-event record time (0~10 seconds)
‧Record time setting
‧Record path
Note: The record function will be disabled when the reserved disk capacity in “Reserved(MB)” is larger than
the current disk capacity in “Free(MB)”.
When “Manual” is checked, click “ ” or “ ” on the main control panel to start the manual recording
immediately, and the recordings will be saved in the location specified in “Record Path”.
When “Motion” and / or “Alarm” are checked, the recording function will be enabled for any motion or alarm event,
and the recordings will be saved in the location specified in “Record Path”.
3.3.2 Playback
To play a recording, click “ ” or “ ”, and select the “Record” tab. A list of all the recordings will be shown by
defaults, and you can also sort out the logs you want to speed up the search time.

6
3.3.3 Firmware Upgrade
This function is used when users need to upgrade the network camera for function scalability.
Note: Before using this function, make sure you have the correct upgrade files provided by your installer or
distributor.
Step1: Click “ ”, and select the IP address of your network camera in the address book.
Step2: Click “ ” to show the upgrade page, “Update Server”.
Step3: Click “Add” to browse to the upgrade files.
Step4: Click “Upgrade Firmware” to start firmware upgrade.
Note: It takes a few minutes to finish the upgrade process. Do not disconnect the power during firmware
upgrade, or the upgrade may be failed. The camera will reboot after the upgrade.
Step5: Select the IP address of the camera and click “ ” again to check if the firmware is upgraded.
3.3.4 E-Map
Video Viewer is also a Central Management System (CMS) software, which allows network device control &
management for up to 16 devices simultaneously.
Note: Before using this function, make sure Video Viewer is connected to all the devices (up to 16) you want
to monitor.
E-Map is ONLY available when the control panel is switch to the full function version.
How to Add an E-Map Group
STEP1: In the simplified version, click “ ” to switch the control panel to the full function version, and click “ ”
to enter the E-Map page as follows.
Note: To know where the buttons are, please refer to “3.2.1 Simplified Version (Default)” at page 3, and
“3.2.2 Full Function Version” at page 4.

7
STEP2: Right-click to show the shortcut menu on the top-left panel, and select the E-Map group you want to add.
There are three E-Map groups you can add: Google E-MAP, Single E-MAP, and Building E-MAP.

8
STEP3: When the E-Map group is created, you will see the tree on the top-left panel, showing all the devices
you’ve added to this group.
Icon Description
The connected device is camera. When it’s selected, it will become red.
The connected device is DVR. When it’s selected, it will become red.
For any motion or alarm event, it will appear on the screen to catch your attention.
To know what’s happening quickly, double-click the device icon on the E-Map to show the live view.

9
How to Edit / Remove an Existing E-Map Group
For Google E-Map Group
Right-click on the group name to show the shortcut menu list, and select
“Edit E-MAP” or “Remove E-MAP” as needed.
You can also add a single E-Map group (Add Single E-MAP) or Building
E-Map group (Add Building E-MAP) into the existing Google E-Map
group.
For Single E-Map Group
Right-click on the group name to show the shortcut menu list, and select
“Edit E-MAP” or “Remove E-MAP” as needed.

10
For Building E-Map Group
Right-click on the group name to show the shortcut menu list, and select
“Edit Building E-MAP” or “Remove E-MAP” as needed.
3.3.5 Smart Zoom
Click or to display the PTZ control panel as follows.
Function Button Description
Simplified Full Function
Smart Zoom
Click to activate the smart zoom function.
There are three statuses when this function is activated:
Idle: This function is currently paused and will be resumed after the
specified time you set in “4.4 Camera” at page 19.
Standby: This function is on and ready to work once an object comes
into the surveillance area.
Active: This function starts to zoom in / out on the object coming into
the surveillance area.
Note: The smart zoom status is displayed on the screen only when
“OSD: Smart Zoom” is selected in “System”. For details,
please refer to “4.4.1 System” at page 20.
Zoom In / Out / / Click to zoom in / out on the image.
Max Zoom In / Out / / Click to zoom in on the image to the largest / zoom out on the image
to its original size.

11
4. SYSTEM CONFIGURATION
Before using the network camera, make sure you have installed the supplied software, “Video
Viewer”, and configure network settings. If not, please refer to your installer or the installation guide.
Note: It’s recommended to consult with your installer before changing system
configurations.
Note: You need to be the supervisor to enter the system configuration page. If not, please
re-log into the camera with the supervisor user level.
Click “ ” and select “ ” to enter the system configuration page. All the system configurations
are listed as a tree structure on the left panel as follows.
Main Menu Sub-menu What you can do for this function?
General 1. Check the firmware version & MAC address of the camera.
2. Change the camera title.
Log Check the system event logs.
Account 1. Create a new user account with different access privilege.
2. Modify or delete an existing user account.
OnLineUser Check the current online user(s).
Trigger 1. Enable / disable the motion detection.
2. Set the motion detection area.
3. Select the event notification method.
Network Configure network settings.
QoS Limit the data flow for live streaming.
DDNS Enter DDNS information when the network type is PPPOE or DHCP.
SNTP Synchronize your camera time with the networked computer systems.
FTP Enter the FTP information for event notifications when “FTP” is chosen in “General” →
“Trigger”.
MAIL Enter Email information for event notifications when “Email” is chosen in “General” →
“Trigger”.
SMS Enter text messaging information for SMS notifications when “SMS” is chosen in “General”
→“Trigger”.
Filter Choose to permit or block the IP address(es) which can access this camera.
UPnP Allow this camera to be detected among devices within the same network area for easy and
quick usage.
Video Set the image resolution, quality and frame rate.
Camera Adjust the camera parameters if necessary.
System Click to set the camera OSD display.
Color Adjust the color performance.
Time Set daylight saving time and the current time.

12
4.1 General
In “General”, you can check the general information for your network camera, such as the firmware
version and MAC address, and also modify the identification name of your camera (up to 15
alphanumeric characters).
4.1.1 Log
To quickly search the system log you want by event type, click the drop-down list to select the
system log type you want to check, and click “Reload” to refresh the list.
To clear all system event logs, click “Clear”.
4.1.2 Account
You can create a new account with different user access privilege, or delete or modify an
existing account setting.
How to create a new account
Step1: Click “New”, and fill in the following columns.

13
Column Description
User Name Set a user name that will be used for camera access. The user name allows up to 16 alphanumeric characters.
Password Set the password that will be used for remote login. The password allows up to 16 alphanumeric characters.
User Level Set the security level of an account to give the permission to control different functions. There are four user
levels: Supervisor, Power User, Normal User and Guest.
Life Time Select how long this account is allowed to stay online (1 MIN / 5 MIN / 10 MIN / 1 HOUR / 1 DAY / INFINITE)
Step2: Then, click “Apply” to save your setting and create a new account.
How to modify or delete an existing account
Step1: Select the account you want to modify or delete.
Step2: To modify the account, change the setting directly, and click “Apply”.
To remove the account, click “Delete”.
Note: It’s not allowed to remove an account when there’s only one account in the account
list.

14
4.1.3 OnLineUser
You can check the current online user(s) with respective online information. To refresh the list,
click “Refresh”.
4.1.4 Trigger
You can set the motion or alarm detection and select the notification function.
Trigger Setting
In this section, you can select to enable or disable the alarm or motion detection.
Item Description
Motion Select to enable or disable the motion detection function.
‧ Motion Detection Area Setting
When “Enable” is selected, click “Setting” to enter the motion detection area setting page as follows:
Sensitivity:
Set the detection sensitivity (High / Normal / Low).
Area Setting:
Set the motion detection area by selecting the area grids with your mouse. Pink grids represent the area that is not being
detected while the transparent grids are the area under detection. You can set multiple areas under detection.
Click “－” (Clear All) to set the whole area undetected.
Click “＋” (Select All) to set the whole area under detection.
Duration Set the duration time for trigger recording (5 / 10 / 20 / 40 seconds).

15
Notification Setting
In this section, you can select to enable e-mail and/or FTP notification when an alarm or a
motion happened.
Item Description
Method ‧Email
When this option is checked, the network camera will upload the captured video clip to the assigned
e-mail address(s) once motion or alarm recording happened.
‧FTP
When this option is checked, the network camera will upload the captured video clip to the specified
FTP site once motion or alarm recording happened.
‧SMS
When this option is checked, the network camera will send a text message to the specified mobile
phone number once motion or alarm recording happened. For details, please refer to “4.2.6 SMS” at
page 17.
Video Type Select the file type of the notification files: H264 (video) / MPEG4 (video) / JPEG (image).
Total Set the record time of the notification video clip (1 ~ 5 seconds).
4.2 Network
You can set the network configuration of the network camera depending on your network type. For
details, please refer to your installation guide.
4.2.1 QoS
QoS, Quality of Service, is the ability to control the data flow for real-time streaming. This
function is important if your network bandwidth is insufficient and you have other devices to
share the network bandwidth.
Check “QoS Enable”, and set the max. upload rate from 256 to 10240 kbps.
4.2.2 DDNS
Select “On” when the selected network type in “Network” is “PPPOE” or “DHCP”. For details,
please refer to the installation guide.

16
4.2.3 SNTP
SNTP (Simple Network Time Protocol) is used to synchronize your camera time with the
networked computer systems.
Function Description
GMT (Greenwich Mean Time) Once users choose the time zone, the network camera will adjust the local area time
of the system automatically.
Server Name Simply use the default SNTP server (For example, tock.stdtime.gov.tw) or change to
another server with which users are familiar.
Sync. Period Select “Daily” to synchronize the camera time with the network time every day or
“None” to turn off this function.
Sync Server Time Click and the network camera will synchronize the time with the network time.
4.2.4 FTP
Enter the detailed FTP information and click “Apply” to confirm. The information you set here
will be applied when “FTP” is selected in “General” →"Trigger".
4.2.5 MAIL
Enter the detailed e-mail information and click “Apply” to confirm. The information you set here
will be applied when “Email” is selected in “General” →"Trigger".

17
Function Description
Server Enter the SMTP server address provided from your e-mail system supplier.
Port Enter the port number provided from your e-mail system supplier. If this column is left blank, the
e-mail server will use port 25 to send e-mails.
Mail From Enter your name or the title you want the receiver to know where this mail is from.
SSL Encryption Select “Yes” if your e-mail server is using SSL encryption to protect your e-mail content from
unauthorized access.
Verify Password Some mail servers are required to verify the password. Please enter the “user name” and
“password”.
Email Address Add the e-mail address(s) of the assigned recipient(s).
4.2.6 SMS
Note: Before using this function, you need to apply an API ID from the mobile messaging
company, Clickatell, and you will be charged starting from the 11th message. For
details, please refer to “APPENDIX 2 API ID APPLICATION FOR SMS MESSAGING’ at
page 27.
Enter the detailed information needed for text messaging, and click “Apply” to confirm. The
information you set here will be applied when “SMS” is selected in “General” →"Trigger".
Function Description
System The text messaging service provider is Clickatell.
API ID Enter the API ID you applied from Clickatell.
User name / Password Enter the account user name and password you created in Clickatell.
Interval Set the interval time in minutes between two-message sending.
The options are 0, 15, 30 & 60.
For example, when the interval is set to 15, the SMS will be sent after 15 minutes, 30 minutes,
& 45 minutes, etc.
Reset Counter Click to restart the text messaging, and the SMS will be sent after the specified time interval
since you click this button.
Message Enter the text content (up to 70 characters) you want to send with the text message.
To know where the event comes from, check “Include Hostname or IP”, and the IP address or
host name of the device will be prefixed automatically to the message.