Digitus DN-16059 User manual

OUTDOOR IR
NETWORK CAMERA SERIES
Installation Guide
Please read instructions thoroughly before operation and retain it for future reference.

1
TABLE OF CONTENTS
1. OVERVIEW..............................................................................................................................1
1.1 Package Content .......................................................................................................................................... 1
1.2 Dimensions ................................................................................................................................................... 1
1.3 Cable Overview............................................................................................................................................. 1
2. INSTALLATION & CONNECTION ...........................................................................................2
2.1 Install the Camera......................................................................................................................................... 2
2.2 Connect to power.......................................................................................................................................... 3
3. ETHERNET CONNECTION.....................................................................................................4
3.1 Network Connection via LAN..................................................................Fehler! Textmarke nicht definiert.
3.2 Network Configurations via Wizard............................................................................................................... 8
3.2.1 Setting in Wizard ............................................................................................................................... 8
3.2.2 DDNS Setting.................................................................................................................................. 10
3.3 Network Configurations via Web Browser .................................................................................................. 12
APPENDIX 1 CREATING AN ACCOUNT FOR DDNS SERVICE ..........................15
APPENDIX 2 IVS CONFIGURATIONS..........................................................................18
A2.1 Intelligent Video System........................................................................................................................... 18
A2.2 Face Tracking ........................................................................................................................................... 20
APPENDIX 3 DIGITAL PTZ (DPTZ) OPERATIONS ...................................................21

1
1. OVERVIEW
1.1 Package Content
□Network camera □Installation Sticker
□Installation Guide □RJ45 cable extender adapter
□CD-ROM disc (including user manuals & CMS software “Video Viewer”)
1.2 Dimensions
246.87
282.4
236.03
212.63
117.89
1.3 Cable Overview
CABLE DESCRIPTION
RJ45 network cable Connect it to the supplied RJ45 cable extender adapter for cable extension, and
prepare another RJ45 network cable with suitable length for your connection.
Reset wires Remove the insulating coating of these two wires, and twist them together to reset
default. This will reset all parameters, including the IP address to factory default
settings.
Note: Disconnect power before twisting these two wires together, and connect to
power again for reset default.
Power cable Connect to DC12V power supply.

2
2. INSTALLATION & CONNECTION
2.1 Install the Camera
Note: The illustration below is for installation only, and the actual product may look
different from the illustration below.

3
2.2 Connect to power
Connect the power adapter (optional) to the camera’s power connector and power outlet.
Note: The regulated power adapter is DC12V to operate this device.

4
3. ETHERNET CONNECTION
Before using this network camera, please follow the instructions below to finish the
network connection settings based on your installation environment:
To configure the network settings, you must connect the camera to your PC by LAN.
For details, please refer to “3.1 Network Connection via LAN” at page 4.
To configure the network settings via the setting wizard, please refer to “3.2
Network Configurations via Wizard” at page 8.
To configure the network settings via a web browser, please refer to “3.3 Network
Configurations via Web Browser” at page 12.
3.1 Network Connection via LAN
Step1:Connect this network camera and your PC via a RJ45 network cable, and make
sure the camera is powered on.
Step2:Set the PC’s IP address as “192.168.1.XXX” (1~255, except 10).
For Windows 2000 users:
a) Select “Start” “Settings” “Network and Dial-up Connections”.
b) Right-click on “Local Area Connection”, and select “Properties”.
c) In the “General” tab, select “Internet Protocol (TCP/IP)”, and select “Properties”.

5
d) In the “General” tab, select “Use the following IP address”, and set the IP address as
described below.
Note: It’s recommended to note down the current settings first and then change
as instructed. It’s helpful when you need to restore the PC network settings
for connecting to Internet later.
e) Click “OK” to close the “Internet Protocol (TCP/IP) Properties” dialog box. Then, click “Close”
to close the “Local Area Connection Properties” dialog box.
For Windows XP users:
a) Select “start” “Control Panel” “Network and Internet Connections” “Network
Connections” (If you’re in “Category View”).

6
b) In “LAN or High-Speed Internet”, right-click on “Local Area Connection”, and select
“Properties”.
c) In the “General” tab, select “Internet Protocol (TCP/IP)”, and select “Properties”.
d) In the “General” tab, select “Use the following IP address”, and set the IP address to
“192.168.1.XXX” (XXX can be any value from 1~255 except 10).
Note: It’s recommended to note down the current settings first and then change
as instructed. It’s helpful when you need to restore the PC network settings
for connecting to Internet later.
e) Click “OK” to close the “Internet Protocol (TCP/IP) Properties” dialog box. Then, click “Close”
to close the “Local Area Connection Properties” dialog box.
For Windows Vista users:
a) Select “ ” (start) “Control Panel” “Network and Internet” to enter the “Network and
Sharing Center”. Then, click “Manage network connections” (If you’re in “Category View”).
b) Right-click on “Local Area Connection”, and select “Properties”.
c) In the “Networking” tab, select “Internet Protocol Version 4 (TCP/IPv4)”, and select
“Properties”.

7
d) In the “General” tab, select “Use the following IP address”, and set the IP address as
described below.
Note: It’s recommended to note down the current settings first and then change
as instructed. It’s helpful when you need to restore the PC network settings
for connecting to Internet later.
e) Click “OK” to close the “Internet Protocol Version 4 (TCP/IPv4) Properties” dialog box. Then,
click “Close” to close the “Local Area Connection Properties” dialog box.

8
3.2 Network Configurations via Wizard
For selected models only, a quick installation wizard is available via your web browser for
password change, date & time settings, and network configurations.
For details about the wizard, please refer to “3.2.1 Setting in Wizard” at page 8.
For details about DDNS setting for PPPoE and DHCP, please refer to “3.2.2 DDNS
Setting” at page 10.
Note: You can also change the settings in the system configuration page via your
web browser later. For details, please refer to “3.3 Network Configurations
via Web Browser” at 12.
3.2.1 Setting in Wizard
Step1:Open your web browser, for example, Microsoft Internet Explorer, and enter
“http://192.168.1.10” in the URL address box.
Step2:In the login page, key in the default user name (admin) and password (admin),
and enter the security code from the image below if any. Then, click “LOGIN”.
Step3:The wizard is then starting analyzing your network environment, and shows your
network environment. Select “Next” to continue.
Step4:In “Account”, change the access password if needed.
If not, leave all the columns blank, and select “Next”.
Step5:In “Date and Time”, check if the date and time setting are correct and modify if
necessary.