Digitus DN-95341-1 User manual

8 Port Gigabit PoE Switch,
19 Inch, Unmanaged,
2 SFP Uplink
Quick Installation Guide
DN-95341-1

2
1. Introduction
The DIGITUS 8-Port Gigabit Rack mount Switch with eight Power over Ethernet ports
and two additional SFP Fiber Port, offers your network significant improvement in
terms of performance and efficiency. Thanks to PoE support, you only need a single
(network) cable for power and data transfer. This switch makes it much easier to
connect devices such as access points, network cameras, and IP telephones, and
requires far less cabling than alternatives. It also allows you to extend your network
in places where there are no power supply cables or sockets available. The switch
does not require any configuration and therefore guarantees quick and seamless
integration into the network. Moreover, the switch has a rack mountable design and
can be easily installed with many standard racks, which makes this device the perfect
solution for data center and local server rooms.
2. Features
8-Port 10/100/1000 Mbps PoE Gigabit rack mountable Switch + 2x SFP Uplink
Ethernet IEEE802.3 / 802.3u / 802.3x/802.3ab/802.3z / IEEE802.3 af/at
Power over Ethernet (PoE) - You only need one cable for power and data transfer
PoE power budget: 140 Watts
Supports PoE: Provides 8 PoE Port, each port output 30W maximum power
No configuration necessary
Status LEDs on each port
Pin Feet: V+ (RJ45 Pin 3, 6) V- (RJ45 Pin 1, 2)
Backplane: 20Gbps
MAC address table: 4K
Rack mountable in system rack (1U)
Internal power supply: 150W
Dimensions (L x W x H): 275 mm x 200 mm x 44 mm
Weight: 4500g
Ethernet speed: Gigabit
Number of ports (uplink): 2
Connection of uplink port: SFP
VLAN: no
PoE standard: IEEE802.3at (PoE+)
3. Package Contents
8P POE switch 2 SFP Uplink Ports
User Manual
Power Cable
Rubber feet 4pcs
Mounting brackets 2pcs
Screws 6pcs

3
4. Specifications
Fixed port
8 x 10/100/1000Mbps PoE ports and
2 Gigabit SFP Ports
Standards and protocols
IEEE802.3 10Base-T Ethernet standard
IEEE802.3u 100Base-TX Fast Ethernet standard
IEEE802.3ab 1000Base-T Ethernet standard
IEEE802.3z Gigabit Ethernet (fiber)
IEEE802.3x Full duplex flow control and
Backpressure Half duplex flow control
IEEE802.3ab Link aggregation
Forwarding Rate
10/100/1000Mbps
LED Indicators
Power, Link/Act, PoE
AC Input Voltage Range
100V～240V AC，50/60Hz
Operating temperature
0°C ~ 40°C
Storage temperature
-10°C ~ 70°C
Operating humidity
5%～95% (non-condensing)
Exchange capacity
20G
MAC Addresses
4K
Power Supply
150W
Power Consumption
10W
PoE Technology
PoE Compliance
100% IEEE 802.3af, 802.3at compliant
PoE Classification
PSE (Power Sourcing Equipment)
PoE Voltage
+52 VDC
PoE Power Budget
140W
PoE Power
Up to 30 W per port
PoE Operation
Automatic detection and power management
PoE Pin Assignments
V+ (RJ45 Pin 3, 6), V- (RJ45 Pin 1, 2)
PoE Disconnect Mode
DC disconnect
Mechanical
Casing
Metal
Dimensions (W x L x H)
275mm x 200mm x 44 mm
Installation
Rack mounting or Desktop

4
5. External Component Description
Front Panel
The front panel consists of LED indications and network ports.
PWR LED: The Power LED lights up when the Switch is connected to a power source.
Link/Act LED: The Link/Act LED flashes which indicates a network link through the
corresponding port. Blinking indicates that the Switch is either sending or receiving
data to the port.
PoE indicator: constant brightness indicates that the PD device is connected to the
corresponding port, and extinguished indicates that the port is not powered or no PD
device is found.
Real Panel
The rear panel view of the Switch consists of an AC power connector.
Power outlet: Supports input voltages 100-240VAC, 50/60Hz.
Switch: Used to connect the power supply.
Fuse: Prevent affect the power grid from equipment short circuit.
(Tank containing a spare fuse)
Grounding: use specialized ground lead connect.

5
6. Hardware installation
6.1 switch installation
For safe switch installation and operation,
it is recommended that you:
Visually inspect the power cord to see that it is secured fully to the AC power
connector
Make sure that there is proper heat dissipation and adequate ventilation around
the switch.
Do not place heavy objects on the switch.
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the
device must be attached on the bottom at each corner of the device's base. Allow
enough ventilation space between the device and the objects around it.
Rack Installation
The switch can be mounted in an EIA standard size 19-inch rack, which can be placed
in a wiring closet with other equipment. To install, attach the mounting brackets to
the switch's side panels (one on each side) and secure them with the screws
provided (please note that these brackets are not designed for palm size switches).
Then, use the screws provided with the equipment rack to mount the switch in the
rack.

6
6.2 Plugging in the AC Power Cord
You can connect AC power supply cord to switch back and the other side connect the
power outlet. (Power outlet might as well grounding and support over voltage
protection)
Warning: Do not turn on the power switch before power cables are connected.
Power surge may cause damage to the Switch.
Power failure
As a precaution, the switch should be unplugged in case of power failure. When power
is resumed, plug the switch back in.
Network connection
1
Monitor
2
NVR
3
PoE IP Camera
CE Mark Warning: This is a Class A product. In home environment, this product may
cause radio interference. In this case, the user may be required to take appropriate
measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is
part of the shipping content. If the Declaration of Conformity is missing, you can
request it by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3, 58513 Lüdenscheid, Germany

7