Dimensions Furniture MoDRN Retro Glam Marion User manual

ASSEMBLY INSTRUCTIONS
Model: #9093B
MōDRN Retro Glam Marion Sleigh Base Bookcase
1/16
Lot Number: _________________
Date of Purchase: ___ / ___ / ____
Manufactured by: Dimensions Furniture, Inc
341 Gradle Drive, Carmel, IN 46032
1-866-528-8364 / [e-mail]
WARNING The maximum load capacity as listed above may not be exceeded and is assumed
to be distributed evenly. Exceeding load capacity may result in collapse and possible injury.
Item must be anchored to the wall by using the included no-tip kit.
!
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Thank you for your purchase. We want to make sure it is to your complete satisfaction. Hardware is separated individually for easy
Each shelf has a 25 lbs
Maximum Load,
distributed evenly.
25 lbs
Customer Service - 1-866-528-8364 / [email protected]
Your satisfaction is our top priority. Our products are designed and manufactured to meet the highest quality. In the event that
you have assembly questions, or parts are missing or damaged, please do not return the product.
Our customer service department would appreciate the opportunity to provide any help necessary regarding assembly and to
provide any necessary parts.
If any parts are missing or defective please contact our customer service department.
all present.

!
Assembly should take place in a secure environment that is clean and dry.
Assembly can be done by one person, but two persons are recommended.
Allen wrench available for assembly.
Please check that all parts and hardware are included before beginning assembly.
Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
Please use CAUTION AND CARE WHEN LIFTING the product.
Never stand on the item or use it as a ladder.
Periodically re-tighten all exposed hardware.
If any parts become missing, damaged, or worn, discontinue use until they are replaced with identical parts.










CAUTION ! Please read below statements before beginning assembly.
PRE-ASSEMBLY PREPARATION:
2/16
HARDWARE LIST
31pc
1
2
Long Bolt with Washers
(1/4” x 1-1/2”)
4
Short Bolt with Washers
No-Tip Kit
(1/4”x5/8”)
16pcs
20pcs
H
J
G
Allen Wrench 1pc
PARTS LIST
C
B
D
Top Panel
Cross Rail
Side Frame
Shelf
2pcs
2pcs
1pc
3pcs
A

PRE-ASSEMBLY PREPARATION:
3/16
PARTS LIST
F
Bottom Panel Central Leg 2pcs
1pc
E

Lay a Side Frame on a at surface with the holes facing up as shown. Fasten three Cross Rails to the Side Frame
with six Short Bolts with Washers using an Allen Wrench as shown. NOTE: Tighten evenly. Do not over tighten.
Next, roll the assembly over on its side as shown.
STEP-BY-STEP ASSEMBLY
4Allen Wrench x1
2
B
C
C
C
x6
4/16
Step 1 C BB
42
Short Bolt with Washers
(1/4” x 5/8”)
2
4

Fasten only the top Cross Rail to the other Side Frame with two Short Bolts with Washers using an Allen Wrench
as shown, but keep bolts loose. Flip the assembly upright, as shown.
STEP-BY-STEP ASSEMBLY
B
C
5/16
Step 2 C B 42
4Allen Wrench x1
2x2
Short Bolt with Washers
(1/4” x 5/8”)
42

Fasten the remaining Cross Rails to the Side Frame with four Short Bolts with Washers using an Allen Wrench as
shown, but keep bolts loose. Once all bolts have been inserted, tigthen them while ensuring the Side Frames and Cross
Rails are properly aligned with each other. NOTE: Tighten Evenly. Do Not Overtighten.
Lay the assembly back on the ground as shown.
STEP-BY-STEP ASSEMBLY
6/16
B
C
C
Step 3 C
C
B
B
4
2
4Allen Wrench x1
2x4
Short Bolt with Washers
(1/4” x 5/8”)
42

Fasten the Top Panel to the assembly with four Long Bolts with Washers using an Allen Wrench as shown.
NOTE: Tighten evenly. Do not Over tighten.
STEP-BY-STEP ASSEMBLY
A
7/16
Step 4 41A
4
4
Allen Wrench x1
1x4
Long Bolt with Washers
(1/4” x 1-1/2”)
1

Carefully Guide a Shelf through the Side Frame in the location shown. Once the Shelf is fully inserted, lay it at
and align the corresponding holes on the Shelf and Side Frames . NOTE: To ensure the shelf & frame won’t be
damaged as the shelf is guided through the side frame, make sure to tilt it as shown.
STEP-BY-STEP ASSEMBLY
6/18
B
B
D
8/16
Step 5 D D
D
B
B

STEP-BY-STEP ASSEMBLY
D
9/16
Step 6
4Allen Wrench x1
1x4
Long Bolt with Washers
(1/4” x 1-1/2”)
Fasten the Shelf to the assembly with four Long Bolts with Washers using an Allen Wrench as shown.
NOTE: Tighten evenly. Do not Over tighten.
41D
4
1

STEP-BY-STEP ASSEMBLY
10/16
Step 7
D
B
B
Carefully Guide a Shelf through the Side Frame in the location shown. Once the Shelf is fully inserted, lay it at
and align the corresponding holes on the Shelf and Side Frames . NOTE: To ensure the shelf & frame won’t be
damaged as the shelf is guided through the side frame, make sure to tilt it as shown.
D D
D
B
B

STEP-BY-STEP ASSEMBLY
11/16
Step 8
4Allen Wrench x1
1x4
Long Bolt with Washers
(1/4” x 1-1/2”)
D
Fasten the Shelf to the assembly with four Long Bolts with Washers using an Allen Wrench as shown.
NOTE: Tighten evenly. Do not Over tighten.
41D
4
1

STEP-BY-STEP ASSEMBLY
12/16
Step 9
E
B
B
Carefully Guide the Bottom Panel through the Side Frame in the location shown with the holes facing down. Once
the Bottom Panel is fully inserted, lay it at and align the corresponding holes on the Bottom Panel and Side Frames
. NOTE: To ensure the bottom panel & frame won’t be damaged as the bottom panel is guided through the side frame,
make sure to tilt it as shown.
E
E E
B
B

STEP-BY-STEP ASSEMBLY
13/16
Step 10
4Allen Wrench x1
1x4
Long Bolt with Washers
(1/4” x 1-1/2”)
E
Fasten the Bottom Panel to the assembly with four Long Bolts with Washers using an Allen Wrench as shown.
NOTE: Tighten evenly. Do not Over tighten.
With help, stand the bookcase up
with the bottom facing up
as shown.
41E
4
1

Attach both Central Legs to the assembly, as shown, using eight Short Bolts with Washers . Be sure to leave bolts
loose until each bolt is inserted properly then go back and tighten evenly with an Allen Wrench .
NOTE: Do not over tighten.
With help, ip the assembly upright.
STEP-BY-STEP ASSEMBLY
14/16
Step 11 F 2
4Allen Wrench x1
2x8
Short Bolt with Washers
(1/4” x 5/8”)
4
4
FF
2

With help, move the assembled Bookcase into its desired location. Secure the Bookcase to the wall by using the
included No-Tip Kit . Locate a wall stud behind the Bookcase. Position one of the brackets on a stud approximately 1”
below the top of the Bookcase. Mark and drill a pilot hole into the center of the stud with a 3/32”drill bit. Attach one of
the brackets to the stud with the provided long screw. (PLEASE NOTE: If a stud is not in the desired location to attach
the bracket on the wall, you can use the provided plastic wall anchor. To do this, mark and drill a 1/4” pilot hole into the
dry wall. Insert a plastic wall anchor into the pre-drilled hole until the anchor is ush with the wall surface. Attach the
bracket to the plastic wall anchor with the provided long screw.) Next, mark the back of the Top Panel with the same
alignment as the bracket attached to the wall. Temporarily, move the Bookcase away from the wall to accesss the back
of the Top Panel . Place another bracket on the mark and pre-drill a 3/32” hole in the Top Panel . Attach the bracket
to the Bookcase with the provided short screw. With help, move the Bookcase back into its nal position, taking care to
line up the wall bracket and the Top Panel bracket. Thread a nylon strap through the holes in the brackets and
tighten the strap until snug. Do not over tighten. (IF necessary, a second No-Tip Kit can be installed for added
security.)
STEP-BY-STEP ASSEMBLY
15/16
Step 12
31pc
No-Tip Kit
3
3
A
A
A
A

STEP-BY-STEP ASSEMBLY
Dimensions Furniture, Inc
341 Gradle Drive, Carmel, IN 46032
1-866-528-8364 / suppor[email protected]
LIMITED ONE YEAR WARRANTY
Warranty available to original purchaser only. Proof of purchase is required. This warranty is your sole remedy
for product defect and does not cover damage due to mishandling, misuse, or abuse. The manufacturer is not
responsible for incidental or consequential damages.
16/16
Step 13 Assembly is now complete.
WARNING Item must be anchored to the wall by using the included no-tip kit.
!
It may be necessary to raise or lower leg height
to eliminate wobble. Rotate the adjustable foot
glides right to lower stool. Rotate left to raise
bench.
RAISE LOWER

Printed in China

INSTRUCIONES DE ENSAMBLAJE
Modelo: #9093B
MōDRN Retro Glam Marion Sleigh Base Bookcase
1/16
Numero de Lote: _________________
Fecha de Compra: ___ / ___ / ____
Manufactured by: Dimensions Furniture, Inc
341 Gradle Drive, Carmel, IN 46032
1-866-528-8364 / [e-mail]
!
Cada estante tiene una
capacidad de peso máximo
de 25 libras, distribuida
uniformemente
25 lbs
ADVERTENCIA No se debe exceder la capacidad de peso máximo indicado arriba.
Exceder la capacidad de peso puede provocar un colapso y una posible lesión. Articulo
debe ser ancló a la pared utilizando el kit antivuelco incluido.
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD
POR FAVOR LÉALO Y GUÁRDELO PARA UNA FUTURA REFERENCIA
Gracias por su compra. Queremos asegurarnos que sea de su plena satisfacción. El herraje viene separado
individualmente para facilitar su identicación. Identique y cuente todas sus piezas, asegurándose que
los herrajes coincidan con las ilustraciones mostradas.
Si falta una pieza o está defectuosa comuníquese con nuestro departamento de servicio al cliente.
Servicio al cliente -1866-528-8364/ [email protected]
Su satisfacción es nuestra mayor prioridad. Nuestros productos están diseñados y fabricados, para cumplir
con la más alta calidad.
En caso que tenga preguntas de ensamblaje, de partes faltantes o dañadas por favor no devuelva el
producto.
Nuestro departamento de servicio al cliente agradecerá la oportunidad de brindarle cualquier
ayuda necesaria con respecto al ensamblaje y piezas necesarias.

!










PREPARACIÓN DE PRE-ENSAMBLAJE:
2/16
31pc
1
2
Perno Largo con Arandelas
(1/4” x 1-1/2”)
4
Perno Pequeño con Arandelas
Kit Antivuelco
(1/4”x5/8”)
16pcs
20pcs
H
J
G
Llave Allen 1pc
LISTA DE PIEZAS
C
B
D
Riel Transversal
Marco Lateral
Estante
2pcs
2pcs
1pc
3pcs
A
¡PRECAUCIÓN! Por favor lea las instrucciones antes de comenzar el ensamblaje.
Ensamble en una supercie plana y pareja.
El ensamble debe realizarse en un ambiente limpio y seco.
El ensamble lo puede hacer una sola persona pero se recomienda dos personas.
Hay una llave Allen disponible para el ensamble.
Verique que todas las piezas y los herrajes estén incluidos antes de comenzar el ensamblaje.
Guarde todos los materiales de ensamblaje hasta que se complete el armado para evitar el
descarte accidental de piezas más pequeñas o herramientas.
Por favor use PRECAUCIÓN Y CUIDADO AL LEVANTAR el producto.
Nunca se pare en el producto, ni lo utilice como escalera.
Periódicamente vuelva a ajustar los tornillos expuestos.
Si se pierde, daña o gasta alguna pieza, deje de usarla hasta que sea reemplazada por
por una pieza idéntica.
LISTA DE HERAJE
Panel Superior

PREPARACIÓN PRE-ENSAMBLAJE:
3/16
LISTA DE PIEZAS
F
Panel Inferior Pata Central
2pcs
1pc
E