Dimplex DCB09 User manual

IMPORTANT
Please read this owner’s manual carefully and thoroughly
before installing and operating your room air conditioner.
Please retain this owner’s manual for future reference after
reading it thoroughly.
MODEL:DCB09(2.6kW Cooling / 2.4kW Heating)
DCB14(4.1kW Cooling / 3.6kW Heating)
DCB05C(1.6kW Cooling)
DCBB07C(2.2kW Cooling)

Table of Contents
Page
- 1 -
Introduction
Electrical Specifications
Care and Maintenance
Operating Instructions
Trouble Shooting Guide
2
4
5
6
9
10
Installation Instructions

Introduction
Front Cover
Air inlet grille
(Indoor)
Cabinet
Air outlet grille
(Indoor)
Air inlet grille
(Outdoor)
Control Panel
Air filter
Vent Lever
Control Panel Remote Control
- 2 -
Fig.1-1
SLEEP FAN
TIMER SWING
ON/OFF
MODE
MID
SWING
AUTO
DRY
FAN
COOL
FEEL
SLEEP
TIMER ON
HIGH
LOW
TMIER OFF

- 3 -
Operating Instructions
Control Panel
Remote Control
Indication symbols of LED control panel
Above LED lights on when the relevant mode is in used.
For remote control model
You can easily operate this air conditioner by pressing the relevant buttonson the
control panel as well as the remote controller.
SLEEP FAN
TIMER SWING
ON/OFF
MODE
MID
SWING
AUTO
DRY
FAN
COOL
FEEL
SLEEP
TIMER ON
HIGH
LOW
TMIER OFF
Used to adjust airflow direction.
Used to set or cancel timer operation.
When the unit is in operation, you can set OFF TIMER. When
the unit is off, you can set ON TIMER. Timer setting range is
0 to 24 hours.
If the OFF TIMER is set, the timer LED displays the remaining
time to turn off the unit for only 10 seconds, then LED shifts
to display set temperature.
If you press TIMER button within the 10 seconds, OFF TIMER
will be cancelled.
If the ON TIMER is set, the timer LED displays the remaining
time to turn on the unit. If you want to cancel ON TIMER, press
TIMER button.
Every time you press this button, the air conditioner will turn
on or will be stopped when it is in operation.
Every time you press this button, the operation mode is
changed in sequence:COOLING > FAN ONLY > COOLING
Used to select fan speed in sequence auto, high, mid and low.
This button used to set room temperature in COOLING mode
or used to set time in TIMER mode. If the two keys are
pressed at the same time for more than three seconds, the
temperature LED display will alternate between C and. F
NOTE: Temperature setting range is from 16 to 31 degrees
Celsius
To activate the "SLEEP" function
No.
7
6
1
2
3
4
5
Button Function
No. Button Function
Mid fan speed
High fan speed
Low fan speed
Auto fan speed
Cooling
Fan only(only Cooling Unit)
Display set temp./Display set timer
Timer
Sleep
1
2
3
4
5
6
7
8
9

Operating Instructions
- 4 -
Remote control
The display and some functionsof the remote control may vary according to the
model.
The shape and position of buttons and indicators may vary according to the model,
but the functions are the same.
The unit confirms the correct reception of each press button with a beep.
To select the mode of operation
To activate or deactivate of the movement of the¡°DEFLECTORS¡±.
To activate the function ¡°SLEEP¡±
Decrease the temperature or time by 1 degree
Increase the temperature or time by 1 degree
To switch the conditioner on and off.
To set automatic switching-on/off
To select the fan speed of auto/low/mid/high
No.
8
9
6
MODE
SWING
SLEEP
1
(TEMP DN)
(TEMP UP)
2
3
4
ON/OFF
FAN
5
TIMER
Button Function

DCB05C/DCB07C
RATED VOLTS
AMPS
RECEPTACLE AND FUSE TYPES
DCB09 DCB14
250V 250V
7.1A 8.5A
DCB05C DCB07C
250V 250V
7.1A 7.1A

REMOVE ALL THE SHIPPING PARTS BEFORE INSTALLATION
LOCATION
Select a location that can support the weight of the air conditioner and one that will not
cause increased operation noise and vibration.
Direct sunlight is unfavorable for efficient cooling.
Select a place where there is no obstacles near the air inlet and outlet.
wall thickness is less than 210
lf the wall thickness is more than 210 scrape the wall as
shown above.
Make rear side lower so that waterwill drain out smoothy.
Less than 210
More than 55 Scrape
45
Less
than
210
5-10mm
more
than 400
more
than 400
more
than 500
less
than 210
Installation instructions
- 6 -

Check the capacity of wiring and power outlet. The power outlet should be used
exclusively for the air conditioner. Do not use it with other appliances.
Ground the air conditioner to prevent danger of electric shock.
Connect the air conditioner with power source securely.
Use a fuse as below.
OPERATION
Installation instructions
- 7 -
CAUTION
Before installation,turn off the operation switch and disconnect the power cord.
This appliance isnot intended foruse by persons(including children) with
reduced physical, sensory or mental capabilities,or lack of experience and
knowledge, unless they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their safety. Children
should be supervisedto ensure thatthey do not play with the appliance.
The appliance isfitted with means for disconnection from the supply mains
having a contact separation in all poles that provide full disconnection
under over voltage category IIIconditions, and thesemeans must be
incorporatedin the fixedwiring in accordance with the wiring rules.
Do not install air conditioner in the place where flammable gas leaks are a
possibility.
The minimum clearance from the appliance to combustible surfaces is 100mm;
(Only for electric heating)
The range of external static pressures at which the appliance was tested is 0-5Pa
CAUTION

Installation instructions
- 8 -
1) Remove the front panel. (Fig.5)
Remove the air filter. (Fig.6)
Remove screw at the botton of the front panel. (Fig.7)
Open the panel cover.
2) Remove the screws fix the chassis-fixing board and cabinet.
some Models have two more screws on the back of the
cabinet. (Fig.8)
3)
4)
5)
Grasp the handle on the front of the chassis and carefully
slide the air conditioner unit out of the cabinet. (Fig.9)
lnstall the drain tube connection into the hole provided
at the rear of the air conditioner chassis.(Fig.11)
To meet different requirementsof different type of air
conditioner, there are two kinds of methods for your choice
to treat the condensed water. You can choose back
drainage or bottom drainage.
Bottom drainage way: the drain tray is fixed in position
through four pcs of screws and use the flare nut to block
the back drainage hole.(Fig.15)
Back drainage way using the flare nut to block the bottom
drainage hole and use water outlet pipe to connect the
back drainage hole pay attention to increase the sealing
ring to prevent water leakage.(Fig.16)
lnstall the air conditioner cabinet on the installation shelf
(not included) with screws.(Fig.10)
6) Carefully slide the unit back into the cabinet.(Fig .12)
7) Reinstall the retaining bracket,front panel and mounting
screws.(Fig.8,7,13)
8) Reinstall the air filter.(Fig.14)
Fig.5
Fig.6
Fig.7
Fig.8
Fig.9
Wall
Cabinet
Screw
Installation shelf
Fig.10
Fig.11 Fig.12 Fig.13
Fig.14
drain tray
screw
falre nut
Fig.15
falre nut sealing ring
water outlet pipe
Fig.16

The front cover will accumulate dirt and dust.
To clean it, wipe it with a soft dry cloth. When
it is excessively dirty, wipe it with a soft cloth
dampened with warm water or mild soap, then
wipe it again thoroughly with a soft dry cloth.
AIR FILTER
The air filter should be washed at least once a month. lf the air filter remains
full of dust, the air flow will decrease and the cooling capacity will be reduced.
The filter is behind the cover and to be pulled out from right hand side.
Wash the air filter with water anddetergent.
Rinse with clean water and dry completely before reinstalling.
AIR CLEANING FILTER
FRONT COVER,ETC
The air cleaning filter is attached to the air filter.
Wash the air cleaning filter as well when wash air
filter.
Hot Water
Benzine,acid,etc.
- 9 -
Care and Maintenance
Fig.15 Fig.16
CAUTION
Do not use hot water above 40 C for washing the air filter.
Let the filter dry thoroughly in the shade before reinstalling. Do not expose
it directly on the sun.
Do not operate the air conditioner with the filter removed.
T3 : The ambient temperature for cooling: 25~52 ;condition
The ambient temperature for heating: -5~20 .
T1 condition: The ambient temperature for cooling: 18~43 ;
The ambient temperature for heating: -5~20 .