Dimplex DCPF40CH User manual

For domestic household use
only.
INSTRUCTION MANUAL
40cm HV Pedestal Fan
Model: DCPF40CH

IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND
RETAINED FOR FUTURE REFERENCE. Note also the information
presented on the appliance
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY
AND/OR DAMAGE AND MAY INVALIDATE YOUR WARRANTY
Please read the operating instructions carefully before using your fan for
the first time and keep them in a safe place.
WARNING – This appliance must not be used in a bathroom.
WARNING – Do not use this appliance in the immediate surroundings of a
bath, a shower or a swimming pool.
• If the mains lead is damaged it must only be replaced by the manufacturers
service agent or a similarly qualified person in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure they do not play with the
appliance.
• The fan must always be switched OFF and disconnected from a power
supply before removing the guard for cleaning.
• Never immerse the appliance in water or other liquids.
• Operate this unit only on a firm, flat surface.
• Do not place on soft, unstable or non-horizontal/angled surfaces.
• Never operate the appliance if a cable or connector has been damaged,
after appliance malfunction or if the appliance was dropped or is
otherwise damaged.
• Please ask a professional service agent to repair the product. Improper
repair may cause danger to users.
• Disconnect the appliance from mains power whenever it is not in use,
before relocating it, and before cleaning.
• Operate the appliance only at the voltage specified on the rating label.
• Only connect the unit to a properly installed and easily accessible socket
so that you can quickly disconnect the plug if necessary.
• Do not connect this product to the mains using an extension lead.
• This fan is only intended for INDOOR RESIDENTIAL applications. This fan
should not be used for commercial or industrial or leisure applications
2

or in small enclosed spaces.
• Never use the mains lead as a carrying strap or pulling lead.
• To avoid a fire or electrocution hazard, NEVER put the cord near heat
registers, radiator, stoves or heaters.
• DO NOT cover cord with carpeting, throw rugs, runners, or similar
coverings.
• DO NOT route cord under furniture or appliances. Take care to position
the cord away from traffic areas and where it will not be a tripping
hazard.
• DO NOT use the unit near windows or where water collects. Rain and
water collection may lead to a risk of fire or electric shock.
• Only operate this appliance with a minimum of 50cm clearance all
around i.e. away from walls, furniture and overhanging objects such as
curtains or a shelf.
• WARNING: To avoid danger of suffocation please remove all packaging
materials particularly plastic and EPS and keep these away from
vulnerable people, children and babies.
• NEVER drop or insert any object or fingers into any openings.
• Do not use the appliance in locations where paint, petrol or other
flammable liquids are used or stored.
• Do not use bug sprays or other flammable cleansers/vapour sprays on
or around the unit.
• Always switch off the unit and take the plug out of the socket:
• If you are not using the unit
• Before you clean or carry out maintenance on the unit
• If a fault occurs
• In the event of an electrical storm.
• Avoid electromagnetic interference. Keep the unit at least 1 metre away
from electrical appliances such as televisions & radios.
• DO NOT use this appliance with an extension lead or power board.
3

Exposed to the
weather outdoors
Near water If the power cable
wires are frayed or cut
Where small children
may be left unattended
No extension leads or
power boards.
Where there is risk
of fire or close to
a naked flame
Where the power
cable may be
damaged
On a slope or
uneven surface
Where it may be
damaged by
chemicals
If there is a risk
of water falling on
the unit
Where there is a risk
of interference by
foreign objects
This product is not
made for DIY repair
4

Model no. DCPF40CH
Colour
Chrome
Power supply
220-240V~, 50Hz
Rated power 45W
Speed settings 3
Modes -
Timer -
Air volume 50m3/min
Adjustable height Yes - Max height 1.16m
Tilt adjustable head Y
Horizontal oscillation Y
Noise level (MAX) 65dB(A)
Weight (net) 5.9kg
Dimensions (w x d x h) 450 x 368 x 1160mm
Specification
• For greater precision, please always refer to the rating label placed on the product.
5

Parts
Rear Guard
Motor housing
Stand base
Main pillar
Height adjustment
knob
Upper pillar
Bolt
Power cord
Speed control
Fixing screws
Motor shaft
Fan blade screw
Fan blade
Front guard
Weight
Speed control
Clamping washer
L-shaped screw
Retaining clip
Pivot knob
Adjustment knob
Neck Retaining
screw
Screw
Nut
6

Assembly
First assemble the base to the main pillar - refer to Fig. 1 & instructions below:
Power cord
1. First unscrew the L-shaped screw (18) and remove it and the clamping washer
(17) from the bottom of the main pillar (6).
2. Turn over the stand base (15). Place the weight (16) in its place on the underside
of the base and place the clamping washer (17) in the centre of the weighted
base (16).
3. Thread the L-shaped screw (18) through the assembly and into the thread of
the main pillar (6). Tighten firmly, but do not overtighten.
4. Loosen the height adjustment knob and pull the upper pillar out of the main
pillar and secure the knob to the desired height.
Secondly, attach the motor housing to the base & upper/main pillar - refer to Fig 2
& the instructions below:
1. First remove the pivot knob (7) and the bolt (20) from the top of the upper
pillar (6), then remove the neck retaining screw (8) and small adjustment knob
(19) from the motor housing bracket.
2. Place the motor housing on the top of the upper pillar and thread the large
pivot bolt (20) through the bracket. Screw in the small retaining screw (8) and
tighten, but do not overtighten.
3. Fit the large pivot knob (7) onto the end of the bolt (20) and the small
adjustment knob (19) at the other side above the bolt. Tighten the knobs while
holding the fan motor upright.
Adjustment knob
7

Assembly
Lastly, attach the fan head to the motor - refer to Fig. 3 & the instructions below:
1. Remove the protective sleeve from the motor shaft (12) and the four fixing
screws from the motor housing. Attach the rear guard (4) to the motor housing
(9) using the four screws you just removed. Ensure the handle is at the top.
2. Place the fan blade (3) over the motor shaft (12) and tighten the fan blade
screw completely, ensuring that it tightens against the flat part of the motor
shaft.
3. Remove the front guard screw and nut (2, 5) from the front guard and release
the guard retaining clips (14) around the outside edge outwards.
4. Hang the front guard (1) by its hook over the top of the rear guard (4). Bring the
front guard down to meet the rear guard and fit the guard screw (2) through
the holes in the bottom edge of the guard and tighten with the nut (5). Finally
push the clips inwards until the front guard is attached to the rear guard.
8

1. Place the fan on a firm level surface. Connect the plug to a power supply and
switch on the power.
2. Turn the fan ON by rotating the speed control knob on the motor housing in
clockwise direction.
3. The fan has 3 SPEEDS to choose from, "1" - Low, "2" - Medium, "3" - High.
4. The airflow direction can be adjusted upward/downward by lifting up or pressing
down the motor housing.
NOTE: Only adjust the fan head when the unit is OFF. Be careful not to insert your
fingers through the guard.
5. Push the oscillating knob on the motor housing down to start OSCILLATION. Pull
the oscillation knob up to stop OSCILLATION.
6. Turn the speed control knob anti-clockwise to the “0” position to turn the fan
OFF.
Operation
9

Cleaning
Over time, dust can accumulate on the front & rear grille cover and fan blades, which
can affect the fans performance. It is recommended to clean the fan at least once a
month.
1. Turn the unit OFF and disconnect the appliance from the power supply.
2. Remove any dust build up with a soft brush.
3. Wipe the surface of the unit with a soft damp cloth. Mild detergent can be used
for any stubborn marks.
Do not use abrasive sponges, scouring pads, or a stiff brush to clean this product.
IMPORTANT
The control panel and other parts must not come into contact with water or any
other liquids.
Storage
If not using the unit for an extended period of time. After cleaning please:
• Turn the unit off, unplug and take care of the mains lead & plug.
•
Cover the unit and store it upright in a location where it will not receive direct
sunlight. NB- Prolonged exposure to direct sunlight will discolour the enclosure.
10