Dimplex DF2600 User manual

Service Manual
Model Number:
DF2600
UL Part Number
690893XXXX
7400700100R00
In keeping with our policy of continuous product development, we reserve the right to make changes without notice.
© 2011 Dimplex North America Limited
Dimplex North America Limited
1367 Industrial Road Cambridge ON Canada N1R 7G8
1-888-346-7539 www.dimplex.com
REV PCN DATE
00 - 13-AUG-13
IMPORTANT SAFETY INFORMATION: Always read this manual rst before attempting to service this
replace. For your safety, always comply with all warnings and safety instructions contained in this
manual to prevent personal injury or property damage.

2 www.dimplex.com
Always use a qualied technician or service agency to repair this replace.
!NOTE: Procedures and techniques that are considered important enough to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the
equipment.
WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the
risk of re, serious injury, or death.
OPERATION .........................................................3
MAINTENANCE ......................................................4
EXPLODED PARTS DIAGRAM ..........................................5
REPLACEMENT PARTS................................................5
WIRING DIAGRAM ...................................................6
3-POSITION SWITCH REPLACEMENT....................................7
HEATER ON/OFF SWITCH REPLACEMENT ...............................7
THERMOSTAT CONTROL REPLACEMENT ................................8
REMOTE RECEIVER REPLACEMENT ....................................8
HEATER ASSEMBLY REPLACEMENT ....................................8
POWER CORD REPLACEMENT .........................................9
FLICKER MOTOR & FLICKER ROD REPLACEMENT ........................9
LED DRIVER BOARD REPLACEMENT ...................................10
LED LIGHT ASSEMBLY REPLACEMENT .................................10
LOG SET ASSEMBLY REPLACEMENT ...................................10
TROUBLESHOOTING GUIDE ..........................................12
TABLE OF CONTENTS

3
Remote Operation
The replace is supplied with an integrated On/Off remote
control.
!NOTE: Ensure that the replace 3 position switch is set
to the remote control setting, “II”. To operate, push the ON
button to turn replace on, push the OFF button to turn the
replace off.
!NOTE: Before attempting any operation with the remote
control, pull the plastic insulator strip out from between the
remote casing and battery cover (Figure 5).
Remote Control Initialization/Reprogram
In the event that your remote control ceases to operate
your replace, follow these steps to reinitialize the remote
control and the remote control receiver in the replace:
1. Place the 3-Position Switch (Figure 1A) in the OFF
(“O”) position.
2. Wait a minimum of 5 seconds and then place the 3-Po-
sition Switch in the Remote Control position.
3. Within 10 seconds of changing the switch position,
press the ON button located on the remote control
(Figure 2). This will synchronize the remote control and
the replace receiver.
!NOTE: You will have only 10 seconds to perform this
last step. Failure to do so will result in these steps needing
to be followed again.
Battery Replacement
To replace the battery:
1. Slide battery cover open on the remote control (Figure
2).
2. Correctly install one 12 Volt (A23) battery in the battery
holder.
3. Close the battery cover.
Battery must be recycled or disposed of properly.
Check with your Local Authority or Retailer for recyc-
ling advice in your area
OPERATION
The controls are located on the upper right of the replace.
(Figure 1)
A. 3-Position Switch
The switch has two ON positions marked with “ I“ and “ II “
. The “ I“ position is for manual operation. In this position
the built-in remote control is by-passed.
The “ II “ position is for operating the unit with the provided
remote control.
When in the “ II “ position the unit is operated with the ON
and OFF buttons of the remote control. When the switch is
in the center position the unit is off.
B. Heater ON/OFF Switch
The Heater ON/OFF Switch supplies power to the heater
fan and the heater element. When the switch is in the ON
position the heater operates if the thermostat calls for heat.
!NOTE: The fan will continue running even when the
heater is not, when the Heater Switch is in the ON position.
C. Heater Thermostat Control
To adjust the temperature to your individual requirements,
turn the thermostat control clockwise all the way to turn on
the heater. When the room reaches the desired temper-
ature, turn the thermostat knob counter clockwise until you
hear a click. Leave in this position to maintain the room
temperature at this setting. For additional heat, turn clock-
wise until you hear the click again and the heater will turn
on.
Resetting The Temperature Cutoff Switch
Should the heater overheat, an automatic cut out will turn
the heater off and it will not come back on without being
reset. It can be reset by switching the 3-Position Switch to
OFF and waiting 5 minutes before switching the unit back
on.
CAUTION: If you need to continuously reset the heater,
unplug the unit and call technical support at 1-888-346-
7539.
!NOTE: The heater may emit a slight, harmless odor
when rst used. This odor is a normal condition caused
by initial heating of internal heater parts and will not occur
again.
Figure 2
Figure 1
A
B
C
ON
Button
Battery Cover
OFF
Button
Plastic Strip

4 www.dimplex.com
MAINTENANCE
WARNING: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of re, electric
shock or damage to persons.
Glass Cleaning
The glass is cleaned in the factory during the assembly
operation. During shipment, installation, handling, etc., the
front glass panel may collect dust particles; these can be
removed by dusting lightly with a clean dry cloth.
To remove ngerprints or other marks, the front glass panel
can be cleaned with a damp cloth. The front glass panel
should be completely dried with a lint free cloth to prevent
water spots. To prevent scratching, do not use abrasive
cleaners or spray liquids on the clear door surface.
Compact Fireplace Surface Cleaning
Use warm water only to clean painted surfaces of the
Compact Fireplace. Do not use abrasive cleaners.
Servicing
Except for light bulb replacement and cleaning described
above, an authorized service representative should perform
any other servicing.

5
EXPLODED PARTS DIAGRAM
6
13
2
3
4
5
9
10
8
7
14
12
15
11
1
REPLACEMENT PARTS
1. Log Set Assembly . . . . . . . . . . . . . . . . 0439560300RP
2. Flicker Motor . . . . . . . . . . . . . . . . . . . . 2000220100RP
3. Heater Assembly (with Cutout) ......2203610100RP
4. Thermostat with Knob . . . . . . . . . . . . . 2600090100RP
5. 3 Position Switch. . . . . . . . . . . . . . . . . 2800071100RP
6. Heater On/Off Switch .............2800070700RP
7. Cord Set .......................4100090203RP
8. Flicker Rod .....................5902620100RP
9. Partially Reective Panel ..........5902580300RP
10. Front Glass . . . . . . . . . . . . . . . . . . . . . 5902570200RP
11. Remote Control..................3000370500RP
12. Remote Control Reciever ...........3000380200RP
13. LED Driver Board ................ 3001170100RP
14. LED Light Assembly (2 LED’s) ...... 3001180100RP
15. Felt Feet Pads (set of 4) . . . . . . . . . . . 8600140101RP