Important Safety Advice
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of re, electrical shock and
injury to persons, including the following:
If the appliance is damaged, check with the
supplier before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a
bath, shower or swimming pool.
Do not locate the appliance immediately below
a xed socket outlet or connection box.
The appliance carries the Warning symbol DO
NOT COVER, indicating that it must not be
covered.
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given supervision
or instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children shall not play with the
appliance. Cleaning and user maintenance
shall not be made by Children without
supervision.
Children of less than 3 years should be kept
away unless continuously supervised. Children
aged from 3 years and less than 8 years shall
only switch on/off the appliance provided that
it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning
use of the appliance in a safe way and
understanding the hazards involved. Children
aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance or
perform user maintenance.
Do not use this appliance in series with a
thermal control, a program controller, a timer
or any other device that switches on the heat
automatically, since a re risk exists when the
appliance is accidentally covered or displaced.
Ensure that furniture, curtains or other
combustible material are positioned no closer
than 1 metre from the appliance.
In the event of a fault unplug the appliance.
Unplug the appliance when not required for
long periods.
Although this appliance complies with safety
standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
The appliance must be positioned so that the
plug is accessible.
If the supply cord is damaged it must be
replaced by the manufacturer or service agent
or a similarly qualied person in order to avoid
a hazard.
Keep the supply cord away from the front of
the appliance.
Warning: In order to avoid overheating, do not
cover the appliance. Do not place material or
garments on the appliance, or obstruct the air
circulation around the appliance, for instance
by curtains or furniture, as this could cause
overheating and a re risk.
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Warning: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
CAUTION - Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
This appliance is not equipped with a device
to control the room temperature. Do not use
this appliance in small rooms when they are
occupied by persons not capable of leaving the
room on their own, unless constant supervision
is provided.
This instruction can be found at:
WWW.DIMPLEX.CO.UK
General
Unpack the heater carefully and retain the packaging for possible future
use, in the event of moving or returning the re to your supplier.
The re incorporates a ame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the
year. Using the ame effect on its own only requires little electricity.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the ame effect, this noise will increase slightly when the heat function
is selected. This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked
on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Fixing - see Fig. 1,3 & 4.
It is recommended the appliance be securely xed via the xing holes
on the base.
The product should be located in its intended position and the fret and fuel
bed remove to allow access to the xing holes.
To remove the fret and fuel bed from the re, grip the fret and lift it up and
then out away from the re, place this somewhere safe, next remove the
3 xing screws from the fuel bed and slide it away from the re.(See Fig.
4, shown Stamford Fret shown).
The 2 xing holes should then be marked and pilot holes drilled if required,
screw x the re into position and then ret the fret and fuel bed in reverse
of above.
The Montclair fret removes in the same manner as the Stamford fret.
Manual Controls - see Fig. 2
Three switches provide a choice of heat setting. Each switch is activated
when the bottom half of the switch is pushed in.
Switch 1 Controls the electricity supply to the heater.
Note: This switch must be in the ON position for the heater
to operate with or without heat.
Switch 2 Provides 950 W heat output.
Switch 3 Provides 1900 W output when used in conjunction with switch2
UK
