Dimplex Silverton SVT20 User manual

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)
EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
08/51957/0 Issue 1
SILVERTON
SVT20

GB ................................................................................................ 1
RU................................................................................................. 7

Welcome and Congratulations
Thank you and congratulations for choosing to purchase a Silverton from Dimplex.
Please carefully read and save these instructions.
Caution: Read all instructions and warnings carefully before starting installation. Failure to follow
these instructions may result in a possible electric shock, fire hazard and will void the warranty
Please record your model and seriel number below for future reference: model and serial number
can be found on the Model and Serial Number Label located on the side of the Silverton
Model Number: _________________
Serial Number: __________________
Always use a qualified technician or service agent to repair this Log grate
Note: Procedures and techniques that are considered important enough to emphasise
Caution: Procedures and techniques which, if not carefully followed, will result in damage to the
equipment
Warning: Procedures and techniques which, if not carefully followed, will expose the user to risk
of fire, serious injury or death.
1

Important Instructions
Please read this information guide carefully to be able to safely install, use and maintain your
product
When using electrical appliances, basic precautions should always be followed to reduce the risk
of fire, electrical shock and injury to persons, including the following:
1. WARNING
Do not place material or garments on, or obstruct the air circulation around the appliance.
2. DAMAGE
If the appliance is damaged, check with the supplier before installation and operation.
If the supply cord is damaged it must be replaced by the manufacturer or service agent or a
similarly qualified person in order to avoid a hazard.
3. LOCATION
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower or swimming pool.
Do not locate the fire immediately below a fixed socket outlet or connection box.
Ensure that furniture, curtains or other combustible material are positioned no closer than 1 metre
from the appliance.
4. PLUG POSITIONING
The appliance must be positioned so that the plug is accessible.
Keep the supply cord away from the front of the appliance.
5. UNPLUGGING
In the event of a fault unplug the device.
Unplug the device when not required for long periods.
6. OWNER/USER
This appliance is not intended for use by children or persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance
7. ELECTRCITY
WARNING – THIS APPLIANCE MUST BE EARTHED.
This appliance must be used on an AC ~ supply only and the voltage marked on the appliance
must correspond to the supply voltage.
Before switching on, please read the safety advice and operating instructions.
8. USAGE
Do not burn wood or other materials in the log grate
2

Site Selections and Preparation
This section provides instructions for selecting a location and preparing the site to install the Log
Grate
1. Select a suitable location that ensures the Log Grate is sitting on a hard level surface for
optimum flame effect
2. Allow for approximately 5cm of clearance behing the unit ( from the frame to the back of the
mantle) and 20cm directly above the back log to allow for removal of the Refill Container.
3. Carefully unpack all of the components from the box.
Caution: Handle the logs carefully, that are fragile and can easily crack or break if dropped.
4. Unpack the transducer (contained within the water reservoir) which has been wrapped to protect
it during shipping. See Fig. 1.
To access the transducer;
Remove the top cover by turning the retaining tabs on both ends of the water reservoir.•
Remove any packaging material.•
Install the transducer so that it is sitting level in the circular holding area in the resevoir.•
Orientate the transducer wire so that it does not sit directly above the Emitter and the wire•
passes through the slit in the side of the tank.
Reinstall the top cover and ensure both retaining tabs have been turned so that they are pointing•
inwards.
Note: Completely assemble the unit before filling the water
3
Each log is a separate component that needs to be placed on the grate. Position each log so that
the hook and loop pad on the backside of the log lines up with the corresponding hook and loop
pad on the log grate. These pads assist with securing the logs to the grate. See Fig.A - Fig.J
Note: Each of these logs are hand made, and as such, the hook and loop pads on the logs and
grate may not align perfectly, therefore, we have included additional pads should you need to
reposition them.
Each of the logs contain LED lights to create a flickering effect. During the assembly, each log
requires the electrical connectors on the log and grate to be connected as they are being placed.
In some cases, these wires can have tie wraps added to prevent the wires from being seen after
final assembly. (not included)
Caution: Handle logs carefully, they are fragile and can easily crack or break, if dropped.
Log Grate Assembly

4
Only use filtered tap water in this appliance.
Once installed, never move this appliance or lay it on its back, without draining the water from the
sump and water tank.
If you intend not using the appliance for longer that 2 weeks, drain the water from the reservoir
and refill container.
The refill container, reservoir, cover and container cap must be cleaned once every two weeks,
particularly in hard water areas.
1) Fill and install the Refill Container.
Note: During initial installation, the Refill Container shouldd be refilled after the Reservoir has filled
to ensure maximum operation time.
2) Make sure sure the On/Off switch is switched to Off (refer to Operating Instruction section)
3) Assemble power adapter (Fig. 2). Plug the power adaptor into the front of the unit, then plug the
unit into a power socket
Log Grate Installation
Operation
The manual controls for the Log Grate are located on the right side (Fig. 3).
A. On/Off Switch.
Supplies power to the Log Grate
B. Momentary Button
Pressing this button toggles between Logs, Logs and flame effect, and Off.
Remote Control
The unit is supplied with a radio frequency remote control. This remote control has a range of
approximatly 15m. It does not have to be pointed at the fireplace and can pass through most
obstacles (including walls). It is supplied with one of 243 independent frequencies to prevent
interference with other units. The frequency designation is indicated on the back of the remote
control.
Note: Before attempting any operation with the remote control, pull the plastic insulator strip out
from between the remote casing and the battery cover (Fig. 4).
Remote Control Initialisation/Reprogramming
Follow these steps for remote control initialisation and if required, re-initialisation;
Unplug the power adaptor from the unit.1.
Wait a minimum of five seconds and then plug the power adapter back into the unit2.
Within ten seconds of re-acquiring power, press the ON button located on the remote3.
control (Fig. 4)
This will synchronize the remote control and the receiver
Remote Control Usage
Pressing the On button, on the remote control, switches between the two levels:
Level 1: The Logs and lights are turned on.
Level 2: The logs and lights remain on and the flame effect is activated.
The fireplace can be turned off at any point by pressing the OFF button on the remote control.
Note: Once the mist has been activated, the unit will have to be turned Off, using either the
momentary button, on the unit, on the Off button or the remote control, then back on to return to
Level 1 - Logs and Lights only in operation.

Battery Replacement
To replace the battery,
Slide the battery cover open on the remote control (Fig. 4)1.
Install one 12v (A23) battery in the battery holder2.
Close the battery cover3.
Maintenance
Warning: Disconnect the power before attempting any maintenance or cleaning to reduce the risk
of fire, electric shock or damage to persons.
Log Grate Surface Cleaning
Use a warm damp cloth only to clean surfaces of the Log Grate. Do not use abrasive cleaners.
Water Reservoir
Note: There is no need to remove any of the logs or move the unit to access the water storage
system. However if you decide to to move the unit to perform any cleaning, ensure that the logs
are stable before cleaning.
The water storage system is located behind the back log. It can easily be removed by lifting each
of the components directly up. (Fig. 5).
Note: There are tabs, on each end, that need to be turned to release the component
Caution: Only filtered tap water should be used in the unit to prevent scaling of the components
If you do not intend on using the unit for longer than two weeks, empty and drain the unit of water,
and dry all of the water containing components.
It is recommended that all of the water containing components are cleaned with soap and water
on a biweekly basis. A small brush has been included to assist in cleaning difficult items/areas i.e.
the transducer
Caution: Do not put plastic components into the dishwasher.
Note: If you need to move the unit ensure that all of the components that contain water have been
emptied before relocating.
Additional Information
AFTER SALES SERVICE
Your product is guaranteed for two years from the date of purchase. Within this period, we undertake to repair or
exchange this product free of charge (excluding lamps & subject to availability) provided it has been installed and
operated in accordance with these instructions. Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales information or assistance with this product please contact your supplier. Please retain
your receipt as proof of purchase.
RECYCLING
For electrical products sold within the European Community - At the end of the electrical products useful life
it not be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
5

Symptom Cause Corrective Action
The flame effect will
not start.
Mains plug is not plugged in.
Low water level.
Low voltage connector not connected
properly. (See Fig.5)
The Transducer Unit is not sitting correctly in
the sump
Check plug is connected to wall socket
correctly.
Check that the water tank is full and there is
water in the sump.
Check that the connector is inserted
correctly. (See Fig.5)
Ensure the Transducer in sitting down into
the moulded recess in the sump
The flame effect is too
low.
The Metal Disc in the transducer might be
dirty.
The wire from the Transducer Unit is sitting
over the metal disc
Clean the Metal Disc with soft brush
supplied. See ‘Maintenance.’ for a step by
step procedure.
Direct the wire to the back of the sump and
make sure it sits into the side slot exiting the
sump.
Unpleasant smell
when unit is used.
Dirty or stale water.
Using unfiltered tap water.
Clean the unit as described under
maintenance.
Use only filtered tap water.
Main lamps are not
working and there are
no flames or smoke.
There is no water in the water tank Follow instructions under
Maintenance, ‘Filling the water tank’.
Check the plug is connected to the wall
socket correctly and that Switch ‘A’ Fig. 3 is
in the ‘ON’ ( I ) position.
Troubleshooting
PATENT / PATENT APPLICATION
Products within the Optimyst range are protected by one or more of the following patents and patent applications:
Great Britain GB 2402206, GB 2460259, GB 2460453 , GB 2418014, GB 2465738, GB 2449925, GB 2465537 , GB
2455277 , GB1020534.2, GB1020537.5, GB1110987.3
United States US 7967690, US 2010299980, US 2011062250, US 2008028648, US 13/167,042
Russia RU2008140317
European EP 2029941, EP 2201301, EP 2315976, EP 1787063, EP07723217.1 , EP11170434.2, EP 11170435.9
China CN 101883953, CN 200980128666.2, CN 101057105, CN 101438104
Australia AU 2009248743, AU 2007224634
Canada CA 2725214, CA 2579444, CA 2645939
International Patent Application WO 2006027272
South Africa ZA 200808702
Mexico MX 2008011712
Korea KR 20080113235
Japan JP 2009529649
Brazil BR P10708894-9
India IN 4122/KOLNP/2008
New Zealand NZ 571900
6

Вступление
Поздравляем вас сприобретением камина Silverton марки Dimplex!
Внимательно прочитайте эти инструкции исохраните их.
Осторожно! Перед установкой прибора внимательно прочитайте все инструкции
ипредупреждения. Несоблюдение этих инструкций может привести кпоражению
электрическим током ипожару, атакже является основанием для аннулирования гарантии.
Впишите вследующие поля номер модели исерийный номер (эти номера можно найти на
специальной этикетке сбоку на камине Silverton).
Номер модели: _________________
Серийный номер: __________________
Поручайте ремонт решетки споленьями только квалифицированному специалисту или
агенту по сервисному обслуживанию.
Примечание.Важные процедуры иприемы, на которые следует обратить особенное
внимание.
Осторожно! Процедуры иприемы, несоблюдение которых приводит кповреждению
прибора.
Внимание!Процедуры иприемы, из-за несоблюдения которых возникает опасность
возгорания или получения серьезной травмы, вт. ч. со смертельным исходом.
7

Важные инструкции
Внимательно прочитайте это руководство — оно содержит сведения обезопасной
установке, использовании итехобслуживании прибора.
Чтобы снизить риск воспламенения, поражения электрическим током иполучения травм,
необходимо при использовании электроприборов соблюдать основные меры безопасности.
1. ВНИМАНИЕ!
Не кладите на прибор ткань или одежду ине создавайте препятствия для циркуляции
воздуха вокруг прибора.
2. ПОВРЕЖДЕНИЕ
Если прибор поврежден, перед тем как его устанавливать иэксплуатировать, обратитесь к
поставщику.
Во избежание опасных ситуаций обращайтесь для замены поврежденного шнура питания
кпроизводителю, агенту по сервисному обслуживанию или специалисту аналогичной
квалификации.
3. РАЗМЕЩЕНИЕ
Не используйте прибор вне помещения.
Не используйте прибор внепосредственной близости от ванной комнаты, душа или
бассейна.
Не располагайте камин непосредственно под штепсельной розеткой или соединительной
коробкой.
Убедитесь втом, что на расстоянии 1 мот устройства отсутствует мебель, шторы или другие
горючие предметы.
4. РАСПОЛОЖЕНИЕ ШТЕПСЕЛЬНОЙ ВИЛКИ
Прибор должен быть установлен так, чтобы сохранялся доступ кштепсельной вилке.
Следите за тем, чтобы шнур питания не оказался взоне перед прибором.
5. ОТКЛЮЧЕНИЕ ОТ РОЗЕТКИ
Вслучае неисправности извлеките вилку прибора из розетки.
Отсоединяйте прибор от розетки, если он не используется втечение длительного времени.
6. ВЛАДЕЛЕЦ/ПОЛЬЗОВАТЕЛЬ
Прибор не предназначен для использования детьми, атакже людьми сограниченными
физическими, сенсорными иумственными способностями или недостатком опыта изнаний,
за исключением случаев, когда такие люди находятся под присмотром ответственного за их
безопасность лица или прошли инструктаж по пользованию прибором. Следите, чтобы дети
не играли сприбором.
7. ЭЛЕКТРИЧЕСТВО
ВНИМАНИЕ! ПРИБОР ДОЛЖЕН БЫТЬ ЗАЗЕМЛЕН.
Прибор следует подключать только кисточнику питания переменного тока, при этом
напряжение должно соответствовать указанному на приборе.
Перед включением прибора ознакомьтесь суказаниями по безопасности иинструкцией по
эксплуатации.
8. ИСПОЛЬЗОВАНИЕ
Не сжигайте на решетке древесину идругие материалы.
8