DimSport Rapid Bike User manual

Button (+) increases the value
displayed. Pressed together
with button (-) allows
modifying the brightness
Six EDs indicating the selected
feature
:
TC => Traction Control
EB => Engine Braking
QS => Electronic Quick Shifter
AFR => Air Fuel Ratio
LC => aunch Control
RPM => Revolutions per Minute
Button
MODE
selects
a specific feature and
saves new settings in
Rapid Bike module’s
memory
_
O2 sensor heating
O O2 sensor operating
OO O2 sensor operating / Rapid Bike
is modulating
Quick start guide
full version can be downloaded
from www.rapidbike.com
1. Update the EVO/RACING module firmware with Rapid Bike software version 2.0.6.8 or further
2. Fasten the device, using the supplied Velcro, in a position easy to look at and reach (see picture)
3. Route YOUTUNE wiring harness up to the Rapid Bike module and fasten it to the OEM harness using cable ties
4. Connect the three connectors of YOUTUNE harness to the Rapid Bike main wiring harness
5. Turn ignition on. Device must light up all EDs and the display; then it should set to RPM position showing 0 rpm
PLEASE PAY ATTENTION TO THE FOLLOWIN :
- DO NOT TAKE AWAY YOUR ATTENTION FROM DRIVIN WHILE OPERATIN WITH THIS DEVICE
- USE ONLY WITHIN ENCLOSED RACIN TRACKS, NOT INTENDED FOR STREET AND PUBLIC ROADS USE
- YOUTUNE SPECIFIC FUNCTIONS ARE LISTED FOR EACH SIN LE BIKE MODEL ON RAPID BIKE APPLICATION LIST AVAILABLE ON-LINE
RPM: showing the information listed above; pushing (-) button for 2 seconds it enables a RPM/Speed
Control function to maintain engine rpm at constant level, therefore cruising at constant speed.
(*) Bike models equipped with ride-by-wire system CAN NOT disable this RPM/Speed Control function
by opening at full gas; be sure to use the other two systems as described above
AFR: Changing target value of auto-adaptive feature in order to modify fuel adjustments performed automatically
by EVO and RACING modules and obtain a richer (+ means more gasoline) or leaner (- means less gasoline ) fuel mixture.
Default value is 0 (no variations of auto-adaptive feature's target), and it can be modified of +/- 2 points. An additional push after -2 points value stops
auto-adaptive feature from operating and display shows “OFF”; keep in mind latest correction values will continue to be applied.
YOUTUNE operates directly on the Air/Ruel Ratio with modifications up to +/- 10 points (1 point = 0,1 AFR) ONLY when it is installed one or more My
Tuning Bike unit. An additional push after -9 point value stops this function, while latest correction values continue to be applied.
Button (
-
)
decreases the
value displayed
and activates
RPM/Speed
control
Alphanumeric display shows t
he
value of the selected feature
Ten EDs on a curved line
for
analog representation of specific
values being measure:
blue = low - red = high
RPM
TPS
RPM
AFR
RPM
RPM
Gear TPS
AFR
O2 TPS
+
RPM limiter

2sec.
+
+
+
MODE

2sec.
Full gas*
+
100rpm
-
100rpm
STOP
RPM
limiter
AFR
MODE
AFR
O2 Target
+

AFR
oo
1
AFR
oo
-
1
AFR
oo
2
AFR
oo
-
2
+


AFR
oo
OFF
TEC
HNICAL TERMS
TPS = Throttle Position Sensor
O2 = Oxygen / ambda sensor
Ride-by-wire = Electronic
throttle

AVAILABLE ONLY FOR RAPID BIKE RACING MODULE
Dimsport Srl
Zona Industriale Madonnina - Loc. San Iorio, 8 B
15020 SERRALUNGA DI CREA (AL) - ITALY
T (+39) 0142.9552 F (+39) 0142.940094
E-mail: [e-mail]
is a company of
QS
MODE
6 Gear*
N
Gear* Cut-off
+

Increases kill time
(Cut
-
off)
(max +20ms)
Reduces kill time
(Cut
-
off)
(max -19ms) and turns QS
feature OFF.
TC
MODE
RPM
Traction Control
+

Increases TC sensitivity
(max +5 point)
Reduces TC sensitività
(max -5 point) and turns TC
feature OFF.
EB
MODE
+

Reduces engine braking
(max -19 points) and turns
EB feature OFF.
RPM
Engine Brake
Increases engine braking
(max +20 point)
EB:
modifies the engine braking feature setting
during deceleration to decrease/increase
engine’s braking force. EDs scale shows RPM,
display shows the adjustment applied over the
value being already set inside the module using
RB software.
QS
:
allows modifying kill time of quickshifter
feature in order to ensure the best
performance. EDs scale and display show the
actual gear information (if available) and the kill
time adjustment applied over the value being
already set inside the module using RB
software.
TC:
activates traction control feature and
modifies sensitivity setting over the value being
already set inside the module using the RB
software, to improve safety in all riding
conditions. EDs scale shows RPM, display
shows the adjustment.
LC
MODE
TPS
RPM-START
+
TPS
ON
LC:
activates launch control
by
pushing
(+) button. Display shows ON.
TPS
1 ON
Open the throttle, EDs scale shows reference of
TPS opening. Display confirms Step 1: Rapid Bike
module holds engine RPM at the required level
.
Step 2
activates
while re
leasing the
clutch: engine accelerates while
power output is controlled
preventing rear tyre from spinning
TPS
2 ON
TPS
RPM
RPM Stop
value in the
Rapid
Bike software sets at how
many engine RPM Step 2
comes to an end: C is
automatically disabled and
YOUTUNE switches to default
mode (RPM or the feature
previously stored)
All values and parameters modified
by operating with
YOUTUNE can be
permanently stored in the module’s memory by pushing MODE button.
Rider can restart the bike with the latest configuration.
We highly recommend to download
complete manual from
www.rapidbike.com