Diphano ALEXA 410 Quick reference guide

1/4
INSTRUCTION PAPER
ALEXA 410-412 | Round dining table 148R
1x base
4x bolt M6x20mm
1x pole
4x washer M61x hex key 4mm 4x spring washer M6
Start by unpacking everything carefully. Make sure to cover the floor to prevent any damage or scratching (you can use the cardboard box for this).
CONTENT
A B
G H I J
4x bolt M8x25mm1x hex key 5mm 4x washer M8 4x spring washer M8
DC E F
COMPONENTS TO FIXATE BASE:
COMPONENTS TO FIXATE TABLE TOP/ALU SUPPORT:
STEP 1: CONNECT THE POLE TO THE BASE STEP 2: TURN THE BASE + POLE
C
D
E
F
Use the hex key (C) to assemble the aluminium pole (B) onto the
base (A) as shown in the picture. Make sure you follow the correct
order as indicated by the letters in the picture.
Turn the base with the pole carefully to its normal position with at
least 2 persons.
BOTTOM
BASE
BOTTOM
BASE
ASSEMBLY INSTRUCTIONS BASE + POLE

2/4
INSTRUCTION PAPER
ALEXA 410-412 | Round dining table 148R
ASSEMBLY INSTRUCTIONS TEAK TABLE TOP
STEP 1: SECURE TABLE TOP STEP 2: ADJUST FEET
G
H
I
J
Carefully place the table top (K) onto the pole (B) so the pre-made
holes match. Now use the hex key (G) to fixate the table top (K) onto
the pole (B). Make sure you follow the correct order as indicated by
the letters in the picture.
Check with a spirit level if the table is placed level. If not,
(un)screw the adjustable feet till your table is completely level.
1x teak table top
K
EXTRA COMPONENTS FOR TEAK TABLE TOP:

3/4
INSTRUCTION PAPER
ALEXA 410-412 | Round dining table 148R
ASSEMBLY INSTRUCTIONS CERAMIC TABLE TOP
STEP 1: SECURE ALU SUPPORT
STEP 3: PLACE CERAMIC TABLE TOP
STEP 2: PLACE BUMPERS (AND WASHERS)
STEP 5: ADJUST FEET
G
H
I
J
Carefully place the alu support (M) onto the pole (B) so the pre-made
holes match. Now use the hex key (G) to fixate the alu support (M)
onto the pole (B). Make sure you follow the correct order as indica-
ted by the letters in the picture.
Carefully place the ceramic table top (N) onto the alu support with
minimal 4 persons.
Place the bumpers (O) on the correct positions as shown in the
picture. Check during setup if your ceramic table top (N) is placed
stable onto the alu support (M). If not, you can add plastic washers
(P) on the necessary postions.
Check with a spirit level if the table is placed level. If not,
(un)screw the adjustable feet till your table is completely level.
13x bumper Ø13 M5
O
13x plastic washer M5
P
1x alu support
M
1x ceramic top
N
EXTRA COMPONENTS FOR CERAMIC TABLE TOP:

INSTRUCTION PAPER
4/4
PIDE1812
ALEXA 410-412 | Round dining table 148R
BISTRO TABLES 108 | 74h
ROUND DINING TABLE 148R
EXTENDABLE TABLES 75h
Diphano cannot be held responsible if the assembly instructions are not followed properly.
www.diphano.com
ARMCHAIR FOLDING
DIRECTOR CHAIR BARSTOOLS
77 | 62h FOLDING BEACH CHAIR LOUNGER
ROPE ARMCHAIR
ASSEMBLY INSTRUCTIONS TRESPA®TABLE TOP
STEP 1: SECURE TABLE TOP STEP 2: ADJUST FEET
G
H
I
J
Carefully place the table top (L) onto the pole (B) so the pre-made
holes match. Now use the hex key (G) to fixate the table top (L) onto
the pole (B). Make sure you follow the correct order as indicated by
the letters in the picture.
Check with a spirit level if the table is placed level. If not,
(un)screw the adjustable feet till your table is completely level.
1x Trespa®top
L
EXTRA COMPONENTS FOR TRESPA®TABLE TOP: