Diplomat istella User manual

INSTRUCTION

Followings are the safety instructions & rules required for your safety
when using the safe. We wish you to read the instructions carefully first.
Cautions when placing the safe.
The safe should be put on flat floor.
Don’t place the safe in damp or big temperature fluctuating spot.
The safe is so heavy that it is to be handled very carefully.
Never move the safe with its door opened.
Cautions when using the safe.
Be careful not to close the door roughly.
Children must be off the safe.
Don’t fill the safe full, and put heavy things on the bottom.
Be careful not to forget the code, and keep the instruction separately.
Be careful not to hurt hands or fingers when closing door.
This fire safe is for keeping paper documents, not for data media.
Data media such as CDs or Diskettes are to be stored in data safes.
Cash or jewelries must be stored in certified security safes.
SAFETY INSTRUCTIONS
2

Code Digits
Components
Nomenclature
Instruction
1.5V Alkaline
AA Batteries
(4pcs)
9V Battery
for Alarm
(optional)
Drawer Shelf Shelf Clips
(4pcs)
Alarm
(optional)
Start button
Battery case
Opened
Closed
Error
Alarm
Dual Control
Enter Button Open Button
Battery
Numerals available
Overview
Front
Touch Panel
Inside
Button
Add - on Alarm (optional)
LED Light
3
istella User Manual

2) Pull out Battery Case
slightly to the right.
1 ) Push right side of door
frame.
Prior to using the safe,
1 ) Push right side of door frame to expose battery case.
2) Load batteries.
*
Even if batteries completely exhausted, registered codes are not erased.
3) Replace four batteries
at same time.
1.
When battery icon lights on touch panel, batteries must be replaced.
1 ) Touch logo 2) Touch
USER CODE 3) Touch
OPEN 4) Open the door while
melody rings 3 seconds.
(Bi sound & touch panel lighted)(Touching every code, Bi sound)
(Melody rings, icon )
Factory Code 1 2 3 4
2.
Batteries
Opening
* CAUTION :
1) If a wrong code entered, bi-ric sounds and icon appears on touch panel.
2)
If wrong codes entered 5 times, lock paralyzes 5 minutes. After 5 minutes, paralysis gets released.
- No response. Paralysis time appears 5-4-3-2-1 in turn on touch panel.
3) Don't open door until melody rings and OPEN icon appears.
*
When unlocking, scramble numbers can be put before and/or after real code to avoid peeps.
But, user code should be touched consecutively.
Ex) In case of user code 1-2-3-4-5-6, xxx123456xxxx
4
USER Code
PUSH PULL Replace Batteries

1 ) Press M button on
door back
2) Enter New CODE 3) Touch ENTER
(Bi sound) (Over 4 digits up to 16 digits) (Melody rings 3 seconds)
*
CAUTION : 1) Prior to closing door, confirm if NEW CODE registered correctly.
2) Don’t enter specific code such as telephone number, birthday, consecutive numbers
for security reasons.
*
CAUTION 1) When door not locked, icon appears.
- Check if inside matters hinder locking.
- Please confirm door tightly closed.
2) Don't close door in active bolt exposed.
3) Close door gently.
Closing door, safe automatically locks .
(Melody rings, icon on touch panel)
Keep Door open
3.
5.
4.
Setting User Code
LED Light
Closing
5
istella User Manual
LED lights on 15 seconds
If logo touched, another 15 seconds extended
.
NEW Code

Button
Battery Housing Cover
LED Light
To set/unset
To set/unset
Press BUTTON
(On / Off )
(LED light on/off, 10 seconds required)
Installing
Load an 9V Battery. Install Alarm on door back.
Built-in Alarm
Optional Alarm
(Icon on/off, 10 seconds required)
*
Alarm is automatically released when door is opened.
ㆍ Once alarm system is affected by shock or tilt, it makes horn immediately.
6.
Alarm Setting
To set and unset is same way as below.
To set and unset is same way as below instruction.
6
1 ) Press M button on
door back
2) Touch number 8 3) Touch ENTER
(Bi sound)
(Melody rings 3 seconds)
(Bi sound)

1 ) Press M button on
door back
2) Touch number 9 3) Touch ENTER
(Bi sound)
(Melody rings 3 seconds)
(Bi sound)
6) Open the door while
melody rings 3 seconds.
(Icon on/off)
Enter 2nd code
*
CAUTION : When Dual Locking unsets, 2nd code removed automatically.
*
CAUTION : 2nd user code must be different from 1st code.
To set/unset
To open with dual codes
ㆍ Two different codes required.
ㆍ For dual control, 2nd user code must be entered.
7.
To set and unset is same way as below instruction.
Dual Control
7
istella User Manual
1 ) Press M button on
door back
2) Touch number 2 4) Enter 2nd CODE
(Bi sound)(Melody rings 3 seconds)
5) Touch ENTER 3) Touch ENTER
(Bi sound)
1 ) Touch logo 2) Touch
1st CODE 4) Touch 2nd CODE
5) Touch OPEN
3) Touch OPEN
(Bi sound & touch panel lighted)
(Melody rings, icon flickers)
(Melody rings, icon )
2nd Code
1st Code 2nd Code

Printed in Korea, Apr. , 2018 REV. 2
19 NoksanSandan 261Ro 60Gil Gangseo-gu Busan, Korea TEL [phone] FAX [phone]
Email : [email protected] www.dsafe.kr