Discovery Telecom GSM Lift Watch User manual

GSM Lift Watch
GSM LIFT COMMUNICATION
SYSTEM
Installation guide v1.0
Тел: [phone]
Моб: [phone]
Skype: Discoverytelecom
Mail: [email protected]
www.discoverytelecom.ru

--
142 00 Praha 4
-
1
-
The GSM lift watch is designed for emergency call from lift
cabin ( 1 or 2) to first aid ( service department, security, etc..).
Setting as same as controlling is possible also remotely by
SMS messages( control of lift status, lift reset etc...).
Basic technical parametres:
Power supply 9 to 18VDC, 50 to 500mA (up operation)
backup via acumulator
GSM network 900/1800MHz
Ext.signallization LED or light 12V (24V) max.100mA
Relay contacts 2x 24V/100 mA
Basic unit 195 x 95 x 34 mm
ReMic modul 110 x 78 x 52 mm
Functionality:
•After activation ( button push) progressively call up 8
numbers (MASTER1-8) saved on the SIM card with
automatic call duration max. 4 minutes
•Back call only from MASTER numbers saved on SIM
card.Another calls are refused.
•Credit information at prepaid SIM cards.
Information is sent by SMS to selected number
•Indication of calling as same as connection
•Automatic verification call once for 3 days to TEST
number(s) (TEST1-8) saved on the SIM card
•Command SMS mode for remote control (SMS might
be sent only from TEST numbers):
oControl of 2 relay contacts for lift reset
oStatus of the lift (5 inputs – 2 are blocking inputs)
oMASTER and TEST numbers changing
oControl of GSM network status
Credit information
•2 blocking inputs – emergency call available only during
lift failure

--
142 00 Praha 4 - 2 -
•2 blocking inputs might be used for sending SMS with
info about lift failure (failure signal on input longer than
2 minutes)
•Sending of preprogrammed SMS when is lift failure –
SMS is sending during change of input status longer
than 2 minutes
Emergency call from lift cabin
After button pressing the unit dial up progressively phone
numbers saved as MASTER1 to MASTER8 on SIM card
inserted in GSM modul. When call is succesful the rest of
numbers are not dial. When call is hanged up the unit coming
back to stand by mode. The operation is indicated by internal
signalization. At the moment of activation is closed output of
external signalization I1 (dialling the numbers). After picking
up of call the output is open and the output I2 is closed
(connection established).
Blocking of emergency call
Activation might be blocked by short circuit of appropriate
blocking input (Port4 – lift 1 and Port5 - lift 2). If Port4 (Port5)
is short circuit against ground (lift is not failed) the button for
emergency call is blocked. When Port4 (Port5) is open the
blocking is cancel. Simultaneously (if Port4 (Port5) is open
longer than 2 minutes is sending preprogrammed SMS
message (lift failure) to preprogrammed number.
Back call
The unit might be activated also by incoming call.It is possible
only when you make a call from numbers MASTER1 to
MASTER8 saved on SIM card. The call is connected always to
lift cabin where was pressed button as last.

--
142 00 Praha 4 - 4 -
Remote lift reset
The unit enables remote control of 2 independent relay contact
via SMS (order RES1 and RES2). It useful for switching of
reset inputs of the lift or other control (the relay contacts are
closing for 5 seconds).

--
142 00 Praha 4 - 3 -
It is ensured that back call is going always to lift cabin where
from came last call.
Testing (verification) call
When are saved on the SIM card numbers under name
TEST1 to TEST8 the unit automaticaly call on them once for 3
days. The unit behaviour is the same as when button is
pressed but the call is performed to different group of
numbers. (not MASTER but TEST). The phone numbers
MASTER and TEST might be the same! The difference is
when call is refused. When it is emergency call the unit dial
next number in the order ( if call is not picked up or refused).
When it is testing call the next number in order is dial if call is
not picked up. When call is refused the unit not dial next
number.
Credit status
The unit control status of the SIM card credit when is used
prepaid card. The unit send SMS to preprogrammed number
with notification about low credit. *
* depends on GSM network
The lift status
The data inputs (Port 1-5) are useful either for monitoring of
the lift or for emergency call blocking (Port 4 Port5). The Port1
(close jumper on the PCB) is monitoring the status of powering
(backup). The status all inputs (ports) is accessable remotely
by SMS.
Remote control and setting
All parametres might be control and setting by SMS remotely.
The SMS are accepted only from numbers saved on the SIM
under name TEST1 to TEST8.

--
142 00 Praha 4
-
5
-
The parts of GSM lift Watch:
Basic unit
The speaker
and microphone
module (ReMic)

--
142 00 Praha 4 - 6 -
Indication of
powering GSM
(green LED)
Indication of
GSM operation
(red LED)
Setting microphone sensitivity
–
lift 1
Setting of speaker loudness – lift 1
Setting microphone sensitivity
–
lift 2
Setting of speaker loudness – lift 2
The unit
interface (PC
setting,
testing,
connection of
other systems
etc… )
Screws for backup acumulator
USE WITH CHARGER ONLY!
Screw
terminal – lift 2
Screw terminal
–
lift 1
Screw terminal
-
ports
Indication of inputs status

7
Screw terminal PORT
5 inputs: open = 1
close = 0
c
Screw terminal LIFT1(2)
Screw terminal of ReMic modul
Ground (gnd)
Input of 2. lift blocking
(short circuit against gnd)
Input of 1. lift blocking
(short circuit against gnd)
Screws
relay contact
Screws for connection to
ReMic modul instal in
the lift cabin – connect
together the same
marked screws
M – microphone
G – ground
R – loudspeaker
S - signalization
Screw for connection to basic
unit – connect together the same
marked screws (via above)
Screw for button
-
activation
Screw of indicator I2
Screw of indicator I1
3 inputs for lift status
monitoring
LED lighting when in = 0
Isolated screws – call activation
by leading voltage 12V

8
o 4
30
125
73
Installation:
•Fix the ReMic modul to back side of lift cabin. We
recommend fix it in the head level for better sound. The
microphone The microphone must be free through lift
cabin otherwise the sound from lift cabin will be
wrong!
The loudspeaker and
microphone are in
direction into lift cabin
The fixing of ReMic
modul on the back
side of lift cabin
(for example:
screws)

9
•Fix the basic unit either on lift cabin or in machine room
(neccessary when use it for 2 lift cabins). The GSM signal
determine where basic unit is install. The installation on lift
cabin is easier but you must verify that GSM signal is
available during all lift way. Keep enough space for SIM
card manipulation.

10
•Connect antenna via antenna connector. The antenna must
not be placed inside cover space! It is neccessary to
provide good quality of GSM signal. The location of
"magnetic" antenna is the best on bigger iron subject which
enables to create bigger GSM signal power. It is also
important to place antenna out of basic unit to not
interference the voice channel by GSM radiation ( you
know it from radio in car)
•Up drawing mentioned above connect ReMic modul to
basic unit. To the ReMic modul connect indication And
activation button. Do not connect power supply. At the
basic unit do not connect inputs (port) yet.
The unit programming
The basic unit might be programm by 3 ways:
1. By PC (RS 232) via unit interface.
2. By mobile phone where insert the SIM card.
3. Remotely by SMS messages. On the SIM card must be
already preprogrammed min. MASTER 1 number.
General requirement on numbers and SMS messages
saved on the SIM card
CAUTION: The unit presume that on the SIM card are saved
only information used for operation!!!
On the SIM card are saved all numbers and SMS which are
used by unit. Called numbers after button pressing are saved
under name MASTER1 to MASTER8, eventually TEST1 to
TEST8. The number where is send SMS about credit info is
saved together with message.
Similiary are saved SMS includes numbers where are sent
messages about lift failure.

11
•Programm start without PIN (when you have special unit
issue with preprogrammed PIN – programm appropriate
PIN).
•The index (1-8) after MASTER (TEST) name define order
in which are dial the numbers. Feel free to save as much
MASTERx (TESTx) as you need ( for example: MASTER1
only). CAUTION! All must be written by Capitals ! The
space must not be between name and index
(MASTER1)! Phone numbers must be saved in
international format (for example: [phone]).
•When order of the names is interrupted (for example:
MASTER1, MASTER2,MASTER4) the unit progressively
dial up the numbers until space (in example MASTER1 and
MASTER2). Afterward hang up. The numbers saved after
space are valid for back call (MASTER) and programming
(TEST). The numbers saved after space – it means
numbers which are not dial up – might be multiple (on SIM
card can be saved more numbers under name MASTER4).
It means that numbers which might be used for back call or
programming are limited by SIM card capacity only!
•The unit search preprogrammed SMS up order. On the
SIM must not be saved any other SMS except
programmed. At first position must be saved SMS
message „ BACK UP“ (when you use for setting GSM Lift
SET the „BACK UP“ SMS message is saved
automatically). Position 2 is SMS message – failure lift 1
and Position 3 is SMS message – failure lift 2.

12
The SIM programming on mobile phone
•Insert SIM card to mobile phone .
•To the phone book on the SIM card save phone numbers
where unit is calling during activation (in international
format!) under names MASTER1, MASTER2,…
•When SMS messages are saved on the SIM – erase them.
•Save on the SIM card selected SMS with phone number
where should be sent information about low credit.. The
mesage must be saved in list of SMS as 1.! When SMS
is not saved – it is not send.
•As second SMS saved message with phone number
where should be sent message about failure of lift 1.
•As third SMS saved message with phone number where
should be sent message about failure of lift 2.
When SMS are not saved – it is not send.
•Switch off the mobile phone and take out the SIM card.
Note: during work with mobile progress up mobile guide.SMS
messages (mentioned above) are mostly saved as unsend.
Remote programming via SMS
It is descripe in capture of remote control.
PC programming
It is descripe in guide of setting sw.

13
Operation:
•Insert the SIM card. (SIM card holder release by pushing of
yellow button).
•Connect power supply.
•Green LED signalling GSM powering
light up as same as yellow (red) LED
powering at screw terminal. The red
LED on ReMic modul light up as well.
•3x shortly flash red LED GSM
operation and start flashing in cca 2
second interval.
•LED GSM operation start flashing
quickly – GSM net registration.
•LED GSM operation flashing again in 2 second interval –
stand by mode – wait cca 30 seconds and unit is ready for
operation.
•When programm the unit from PC. Connect the special
cable and make setting.
•Push button (calls must not be blocked – via blocking
inputs): The red LED GSM operation flashing quickly
(dialing preprogrammed numbers). Progresivelly are dial up
numbers saved as MASTERx (when call is not picked up
the unit hang up and dial following number ).

14
In loudspeaker you can hear signals of GSM network (search
called part, ringing tone etc...). The signalization screws I1 of
appropriate ReMic modul are closed. After call picking up by
called part is established connection to lift cabin. The
signalization screws I1 are open and signalization screws I2
are closed. When button is pressed again the unit dial number
in next order (next MASTER).
Adjust the loudness of ReMic modul on the basic unit (thin
screw driver!). Set it carefully to avoid of acoustic short
circuit.
•By hanging up on called part the connection is ended. The
connection is also ended after time out 4 minutes.
•The same test will make at second ReMic modul.
( when you use it for 2nd lift cabin)
•Make incoming call on the unit from selected MASTER
number: your call will be picked up and established
connection to lift cabin. By hanging up the connection is
ended.
•Make incoming call on the unit from none MASTER
number: your call will be refused.
•When is low credit – after connection must be sent SMS
with info about low credit.
•Try sending SMS when lift is failure ( lift blocking – short
circuit on input removed on time longer than 2 minutes).
•Try switching of relay contact for reset.
•Connect data inputs and make rest wiring which has not
been done yet.

15
Remote control and setting by SMS
The unit might be control and setting remotely by SMS. It
might be done only from numbers saved on the SIM card as
TEST1 to TEST8. The SMS from another numbers are
accepted but erased.
CAUTION! When you are erasing numbers remotely
please note that min. 1 TEST number must stay on the SIM
card. Otherwise you cant make any other remote setting..
The SMS messages are always written by CAPITALS.
The SMS are splited to 3 groups.
Order SMS
It is SMS makes some feature. It has not any parametr only
identificator.
STAT, RES1, RES2, RST
Setting SMS
It is SMS makes settings of the unit. It enables make changes
in setting as same as erasing of numbers (MASTER and
TEST) saved on the SIM card. It contains 2 parts seperated
by comma:
MASTERx , [phone]
TESTx , [phone]
System SMS
It is global SMS for control of GSM modul TC 35i.
Those SMS we recommend to be used by qualified person
only!
.
Order bodyIdentificator

16
The system SMS contains 2 parts:
CAL , AT+CSQ
In Order table below we mention some examples of orders.
The full table of orders is available on the base of
your demand !
Order bodyIdentificator

17
ORDER TABLE
ιδεν
τιφ. παρ. ορδερ βοδ ψ εξαµπλε δεσχριπτιον ΣΜΣ ρεπλψ
ΜΑΣ
ΤΕΡ 1 το 8 , πηονε νυµβε ρσ )
1
ΜΑΣΤΕΡ1,[phone] αδδ ορ χηανγε πη ονε
νυµβερ
∀ΟΚ∀
ΜΑΣ
ΤΕΡ 1 το 8 , ΜΑΣΤΕΡ2, ερασινγ τηε πηονε νυµβερ ∀ΟΚ∀
ΤΕΣΤ 1 το 8 , πηονε νυµβε
ρσ )
1
ΤΕΣΤ1,[phone] αδδ ορ χηανγε πη ονε
νυµβερ
∀ΟΚ∀
ΤΕΣΤ 1 το 8 , ΤΕΣΤ2, ερασινγ τηε πηονε
νυµβερ ∀ΟΚ∀
ΣΤΑΤ ΣΤΑΤ στατυσ οφ ινπυτσ
(ΠΟΡΤ)
∀ξξξξξ∀, ωηερε ξ
ισ 0 ορ 1 υπ στατ
υσ οφ αππροπριατ
ε ινπυτ (εξαµπλε :
ωηεν ισ βλοχκινγ
οφ βοτη λιφτσ τη
ε ΣΜΣ
φορµατ ωιλλ βε: ∀
11100∀
ΡΕΣ1 ΡΕΣ1 χλοσινγ οφ ρελαψ
χονταχτ 1 φορ 5
σεχονδσ ( φορ εξα
µπλε
ΡΕΣΕΤ οφ τηε λιφτ
)
∀ΟΚ1∀
ΡΕΣ2 ΡΕΣ2 χλοσινγ οφ ρελαψ
χονταχτ 2
φορ 5 σεχονδσ (
φορ
εξαµπλε ΡΕΣΕΤ ο
φ τηε λιφτ)
∀ΟΚ2∀
ΡΣΤ ΡΣΤ Υνιτ ρεσταρτ ∀ΡΕΣΤΑΡΤ∀
ΧΑΛ , ΑΤ∆6031234
56; ΧΑΛ,ΑΤ∆6031234 56; τηε υνιτ αφτερ ρε
χειϖινγ ΣΜΣ χαλ
λ πρεπρογραµµεδ
νυµβερ)
2
∀ΟΚ∀ − χοννεχτι
ον µαδε
∀ΝΟ ΧΑΡΡΙΕΡ∀ −
υναχχεσαβλε
∀ΒΥΣΨ∀ − βυσψ
ΧΑΛ , ΑΤΗ ΧΑΛ,ΑΤΗ ενδινγ οφ χυρρεντ
χαλλ

18
ΧΑΛ , ΑΤ+ΧΠΑΣ ΧΑΛ,ΑΤ+ΧΠΑΣ στατυσ οφ υνιτ
∀+ΧΠΑΣ: 0∀ − στανδ βψ
∀+ΧΠΑΣ: 3∀
− ινχοµινγ χαλλ ι
σ χοµινγ
∀+ΧΠΑΣ: 4∀
− χοννεχτιον
ΧΑΛ , ΑΤ+ΧΣΘ ΧΑΛ,ΑΤ+ΧΣΘ Υνιτ ΓΣΜ σιγναλ
στρενγητ
∀+ΧΣΘ: 17,99∀ −
φιρστ νυµβερ βεφ
ορε χοµµα ισ σιγν
αλ
στρενγητ (µαξ 32),
µιν.
ϖαλυε φορ οπερα
τιον ισ
χχα 17
ΧΑΛ , ΑΤ+ΧΑΧΜ? ΧΑΛ,ΑΤ+ΧΑΧΜ? χρεδιτ ϖαλυε ατ πρεπαι
δ χαρδ )3
∀+ΧΑΧΜ: 01ΦΑ0
0∀
ΧΑΛ , ΑΤ+ΧΑΜΜ? ΧΑΛ,ΑΤ+ΧΑΜΜ? χρεδιτ µαξιµυµ)
3
∀+ΧΑΜΜ: 00ΦΦ4
Α∀
ΧΑΛ , ΑΤ+ΧΠΒΡ=π
αρ. ΧΑΛ,ΑΤ+ΧΠΒΡ=1 ΜΑΣΤΕΡ ορ ΤΕΣΤ νυµβερ
ασσυρινγ ον ποσι
τιον 1 το 8.
+ΧΠΒΡ: 1,∀+4206
02123111∀,145,∀
ΜΑΣΤΕΡ1∀
ΧΑΛ , ΑΤ+ΧΧΛΚ=? ΧΑΛ,ΑΤ+ΧΧΛΚ=? Χλοχκσ ιν τηε υνι
τ
+ΧΧΛΚ: 00/01/01,
01:17:36 )
3
χλοχκσ αρε σταρ
τινγ φροµ
1.1.00. αφτερ στα
ρτ. Ιτ σηοωσ τηε τ
ιµε οφ οπερατιον
φροµ λαστ σταρτ
(σηορτ φαιλεδ αρ
ε
νοτ ρεγιστρατεδ)

19
FAQ
LEDs are not lighting.
Power supply fault. Verify power supply connection and
polarity.
Does not happen quick flashing of „registration“ - red GSM
LED.
The unit is not registrated to GSM net:
•Fault SIM card (or bad inserted)
•Old 5V SIM card (unit support 3V and less)
•Set registration with PIN
•Bad GSM signal
Nothing happen after button pressing.
On the SIM card are not saved MASTERx numbers.
Appropriate blocking input is short circuit.
In connection you hear interferences.
The power supply is AC or not filtrated enough.
The GSM signal penetrate to voice channel (via. Instalation).
Some wire (except powering) is grounded.
In connection you can hear acoustic shock (whistling, ECHO
etc..)
Too big amplification in whole system (micro of called part
phone – loudspeaker in lift cabin – acoustic parametres of lift
cabin – micro in lift cabin – handset). You have to decrease of
ReMic loudness.
Bad loudness from lift cabin.
Faulty installation of microphone or bad setting of micro
amplification.(via. Instalation).