displayit GRAFFITY:PLUS User manual

displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
1

3-piece channel bar
Snap
Frame Lock
1. Set the frame standing on end. Grasp
two of the middle hubs (circled in
orange) and gently expand the frame.
Note the location of the adjustable feet
for future reference.
4A. Slide one end of the first channel
bar onto the connection point of one
of the corner hubs. The triangular
channel bar’s thinner edge goes
toward the inside of the frame.
4B. Snap the slots in the back of the
channel bar onto the nubs on the hubs.
4C. Attach the other end of the
channel bar to the other corner hub.
Repeat steps 4A-4C for all channel
bars as seen in the diagrams above.
2. Snap all frame locks (marked
in red in the diagrams below) to
secure the frame.
It is recommended to assemble
the frame with it laying on its back.
3. Unfold and slip together each
bungeed channel bar.
Adjustable Feet
5 Foot Frame 8 Foot Frame 10 Foot Frame
4-piece channel bars
3-piece channel bars
3-piece channel bars
3-piece channel bars
2-piece channel bars
3-piece channel bars
Corner Hub
Thinner Edge
Slot
Nub
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
2

Endcap
Channel Bar
Adjustable Foot
Frame Side
Frame Bottom
5. Snap four endcap channel bars onto
the sides of the frame.
6. Carefully stand the frame up with the
adjustable feet on the floor.
Note: This may require two people.
7. If the frame is on an uneven
floor or if it leans, adjust the
bottom feet.
8. On one curtain light, swivel the
four hooks 90 degrees.
9. Rotate the hooks to face the
same direction as the LED lenses.
10. Hang the curtain lights on the frame with the
LED lenses facing forward. The hooks have an
internal spring to allow them to stretch over the
frame poles. Hook all four hooks.
Repeat steps 6-8 for all curtain lights.
LED Lens
Hook
Power In
Power Out
Curtain Light
Hook
up
down
Adjustable
Foot
up
up
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
3

11. Connect each bottom curtain light to a power supply. Power supplies
may be supported on the frame with the included cradles.
12. Connect each upper curtain light to the output from the curtain light
below it.
Tuck the wires behind the frame or lights to reduce shadows.
Power
Supply
Bottom of the Frame
Cradle
13A. Install the back fabric reflector. Begin by tucking the corners and midway across the
top and bottom. The stitched edge of the silicone goes into the SEG channel first.
13B. Complete installation of the fabric.
DO NOT connect more than 3 curtain lights to each transformer.
Top output
Remains
Unplugged
Back of the Frame
Fabric
Reector
Back
SEG
Channel
Stitched edge
goes in first
SEG
groove
Start in
the corner
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
4

A series of tucks reduces excess silicone.Pulling on the silicone welt during installation stretches the silicone and
creates a bulge in the silicone welt that is difficult to correct smoothly.
Tuck Tuck Tuck
Press While
Sliding Hand
Pull
INCORRECT CORRECT
Silicone
Bulge
Graphic Installation Instructions
Caution! Installing silicone-edged graphics is techniqe sensitive;
Practice will shorten installation time.
Handle graphics with care with clean hands in a
clean environment. Clean cloth or latex gloves
are recommended.
How to Install SEG Graphics:
Turn and tuck the side of the graphic with the silicone welt into the SEG groove.
The stitched ege goes into the groove first.
Stitched edge
goes in first
SEG
groove
Start in
the corner
Installing Fabric Graphics with Endcaps
A. Tuck the graphic into left/upper endcap SEG
channel and partially down the vertical channel bar.
B. Holding the graphic off of the ground, tuck the
center of the graphic on the front of the frame.
C. Tuck the graphic into the right endcap.
D. Complete installation of the top
edge of the graphic.
E. Tuck the bottom/front corners
and the middle of the bottom/front.
F. Complete installation on the
bottom/front.
G. Complete installation of both
endcaps.
A
B
C
G
G
G
G
D
D
E
E
E
F
F
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
5

All frame graphics will include a front panel and two side endcap
panels that will be produced as a single fabric graphic.
Backlit graphic frames (black) will also include a blockout graphic for
the back of the frame to prevent light bleed.
Graphic Layout
Panel A
Panel B
Blockout Panel
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
6

Frame Alignment
U - Connector
For Kits that require inline or staggered connections, connect the two
frames together with U-Connecter.
The connector will be used on the tops of the two frames and should
only be placed after the graphics have been installed.
Please reference the frame drawing above for the U-Connector
locations.
*Note: The U-Connectors will only be used on the top of the frames
when making a connection.
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
7

Backlit Counter-to-Go
Assembly
1. Expand the frame with
the adjustable feet pointed
down.
2. Lock the two metal
support brackets to
secure the frame open.
Bag Packing Instructions
Countertop
(Under Flap)
Frame
Endcap
Channel Bars
Channel Bars
(Inside Larger Pocket)
Curtain Light
(Inside Small Pocket)
9. Install the front wrap-around graphics and the back graphics.
See the following page for detailed graphic installation.
Set countertop on top (making sure the frame nubs go into the
recesses). Plug the power cord in to light up the display.
8. Connect the power supply
to the bottom of the curtain
light. Plug the power cord in
and test the lights.
4. Snap the four endcap
channel bars to the top and
bottom sides of the frame.
Diagram showing the locations
of the channel bars required.
7. With the “up” sticker facing
toward the top of the frame,
mount the clips to the frame so
the hooks are facing outward.
Stretch the bottom hooks down
and hook them onto the frame.
up
up
3. Install the 4 front channel
bars and rear 4 back channel
bars. The thinner edge goes
toward the inside of the frame.
Corner Hub
Thinner Edge
Channel Bar
Adjustable
feet
5. Unroll the curtain light and
swivel the four hooks 90 degrees.
6. Rotate the hooks to face the
same direction as the LED lenses.
Power In
Curtain Light
Hook
up
down
LED Lens
Hook
Endcap
Channel
bar
Rear
Vertical
Channel
Bar
“X” Shaped
Strap goes in back
Front
Horizontal
Channel
Bar
Front
Vertical
Channel
Bar
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
8

Bottom Layer Top Layer
Smaller channel bar bag
Frame
Fabric graphics and light blockers
(in plastic bags)
Endcap Channel Bars
Larger channel bar bag 2 padded light bags 2 padded light bags
!
6. Unclasp all locks and let
gravity collapse the frame.
Do not force the frame
closed.
5. Strap channel bars into the
channel bar bags. The front
channel bars go into the larger
bag of the two.
4. Carefully remove all channel
bars from the frame.
Removing channel bars at an angle
applies stress to the end hook
which may become damaged.
CORRECT INCORRECT
End hooks may break
1. Disconnect and remove each
curtain light. Twist (Arrow A) and
and rotate (Arrow B) each hook
for storage.
2. Carefully bundle each curtain
as seen above. Make sure wires
are tucked inside bundle. Secure
with a velcro strap on each end.
3. Stack three light bundles inside
the padded bag. Slide power supply
in cavity beside the curtain lights.
Secure with the bag’s velcro straps
and zip up the bag. Repeat for the
remaining three bags.
B
A
Recommended Packing Order
Packing Instructions in Large Flat-Packer
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
10x10 Inline Display Kit A
Assembly Instructions
Updated 3/15/2019
GRAFFITI:Plus
9