manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Displays2go
  6. •
  7. Lighting Equipment
  8. •
  9. Displays2go SEGL810W User manual

Displays2go SEGL810W User manual

NOTE:
(1) Lay out all extrution panels on a clean, non-abrasive surface and identify each part.
(2) Make sure that you have all included parts before you begin the assembling.
(3) The SEG frame is 8’ in height and 10’ in width. The assembling space must be large enough to house the
entire frame.
(4) For your safety, DO NOT use ladder when assembling the SEG backwall.
(5) Every panel/bar has numbers on both ends. Assemble the frame by matching the numbers.
PARTS LIST
A. Bottom Panel (with holes to fit Foot Plate)
B. Top Panel
C. Middle Panel
D. Side Panel
E. Support Bar - Horizontal
F. Support Bar - Vertical
G. Foot Plate
H. Corner Connector
I. Flat Head Screw
J. Wing Nut
K. Bar Connector
X2
X2
X2
X4
X4
X2
X2
X8
X8
X8
X7
A
E
D
C
F
GH
BIJK
Tools included:
Torx Screwdriver Hex Key (M3) Hex Key (M5)
Ver. 05/19
L. Plastic Clip
M. LED Light Cable
N. Power Adapter
O. LED Light Panel
X16
X1
X1
X2
LM
N
O
1 of 5
IMPORTANT SAFETY INFORMATION:
Please take time to read all instructions before start assembling the unit. Be sure you fully understand all of the
steps needed to finish the assembly. Two or more persons are required.
ASSEMBLY INSTRUCTIONS
8’X10’ SEG BACKWALL WITH LED LIGHT - SEGL810W
Step 1. Connect 2 Bottom Panels (Part A) with 1 Middle Panel (C).
Remove screws from bar connectors on the middle panel. Insert bar connectors into the bottom panels, and fix the
bottom panel assembly by tightening screws back to the bar connectors.
Tips: Use the provided Torx Screwdriver.
Assemble 2 Top panels (B) and 1 Middle Panel (C) the same way.
Step 2. Remove 1 screw on each of 2 Bar Connectors (K) and insert it into the flat end of the Side Panel (D).
Tighten screws back in to fix connecting bars. Remove screws on the other side and insert fixed Bar Connectors
into the Side Panel (D) with matching number. Fix the connecting bars by tightening screws back with provided
Torx screw driver.
TOP PANEL MIDDLE PANEL TOP PANEL
BOTTOM PANEL
MIDDLE PANEL
BOTTOM PANEL
Assemble the other side panel with power entry module the same way.
2 of 5
ASSEMBLY INSTRUCTIONS
8’X10’ SEG BACKWALL WITH LED LIGHT - SEGL810W
Step 3. Connect all assembled panels with Corner Connectors (H) by matching the number on the labels.
Insert Corner Connectors (H) into the channels on sides of the frame panel. Make sure the panels fit together with
no gap, then tighten the insert screw with the provided Allen key. Secure Corner Connectors by pushing the han-
dles down on both sides.
Repeat the step for other corners until the frame is securely assembled.
Step 4. Assemble 2 vertical Support Bars (F) with 1 Bar Connector (H). Place the assembled support bar in the
middle of the SEG frame by matching the numbers on parts (bottom left). Secure the support bar to the center “T”
slot at top and bottom by tightening the screws at both ends.
Assemble 4 horizontal Support Bars (E) the same way. Secure 2 sets of assembled horizontal sopport bars with
the vertical bar and the SEG frame by tightening the screws as shown (bottom right).
3 of 5
ASSEMBLY INSTRUCTIONS
8’X10’ SEG BACKWALL WITH LED LIGHT - SEGL810W
Step 5. Fix Foot Plates (G) to the bottom of the assembled SEG frame by using Hex Screws (I) and Wing Nuts (J).
Step 6. Lay 1 LED Light Panel (O) onto the center groove in the bottom SEG panel, and connect the female end
on LED panel with male end on power module. Fix the LED Panel to the SEG frame by inserting the Plastic Clips
(L) into the slot in the LED Panel. Turn the clips clockwise to lock.
LED LIGHT PANEL
LED LIGHT PANEL LED LIGHT CABLE
Fix the other LED Light Panel (O) to the top the same way. Connect the Light Cable (M) to the power supply
module on the SEG frame and the LED Light Panel on top.
Use wire clips on the SEG frame to attach light cable to the vertical panel inside.
4 of 5
ASSEMBLY INSTRUCTIONS
8’X10’ SEG BACKWALL WITH LED LIGHT - SEGL810W
Step 8. Carefully lift the assembled backwall up to its standing position. Connect the Power Adapter (N) to the
power module from the outside of the SEG frame, then plug in to the power outlet.
Step 7. Assemble the SEG graphics to one side of the frame by inserting the silicon edges into the grooves on the
side of the frame. (For double sided only) Carefully flip the frame and assemble the other side the same way.
Make sure the graphic is fully stretched.
Turn on the power switch at the bottom. The assembly is finished.
If you have any questions regarding our products, please visit us at www.displays2go.com or contact D2G customer service
844-221-3388.
Scan QR code to visit
the product page:
5 of 5
ASSEMBLY INSTRUCTIONS
8’X10’ SEG BACKWALL WITH LED LIGHT - SEGL810W
GRAPHICS

Other Displays2go Lighting Equipment manuals

Displays2go SEG LIGHTBOX User manual

Displays2go

Displays2go SEG LIGHTBOX User manual

Displays2go SEG810WSGH User manual

Displays2go

Displays2go SEG810WSGH User manual

Displays2go DGLED25AND User manual

Displays2go

Displays2go DGLED25AND User manual

Displays2go SPLBP35CP User manual

Displays2go

Displays2go SPLBP35CP User manual

Displays2go SPLBP71CP User manual

Displays2go

Displays2go SPLBP71CP User manual

Popular Lighting Equipment manuals by other brands

E2S IS-L101L instruction manual

E2S

E2S IS-L101L instruction manual

Fomei Terronic Basic Hobby FY4259 user guide

Fomei

Fomei Terronic Basic Hobby FY4259 user guide

Show Technology FusionBAR Q XV user manual

Show Technology

Show Technology FusionBAR Q XV user manual

Original BTC Alma US-FW703 instruction manual

Original BTC

Original BTC Alma US-FW703 instruction manual

Klein Tools 56063 instructions

Klein Tools

Klein Tools 56063 instructions

Gifas ApolloLIGHT operating instructions

Gifas

Gifas ApolloLIGHT operating instructions

Fomei LED ROLL 62 DMX user guide

Fomei

Fomei LED ROLL 62 DMX user guide

Martec Tradetec TLEEC360 user manual

Martec

Martec Tradetec TLEEC360 user manual

V-TAC VT-1607 installation instructions

V-TAC

V-TAC VT-1607 installation instructions

EuroLite LED Bar PIX-24 RGB user manual

EuroLite

EuroLite LED Bar PIX-24 RGB user manual

Zodiac Pool Systems Nature2 Fusion soft Installation and operation manual

Zodiac Pool Systems

Zodiac Pool Systems Nature2 Fusion soft Installation and operation manual

Haneco SKYLUX G4 installation guide

Haneco

Haneco SKYLUX G4 installation guide

SWS 26 Series Installation and operating instructions

SWS

SWS 26 Series Installation and operating instructions

LIGMAN LALUNA 3 installation manual

LIGMAN

LIGMAN LALUNA 3 installation manual

American DJ REVO RAVE User instructions

American DJ

American DJ REVO RAVE User instructions

Verilux HappyLight Liberty Series manual

Verilux

Verilux HappyLight Liberty Series manual

Flight Light L810 Installation and maintenance manual

Flight Light

Flight Light L810 Installation and maintenance manual

Spitzer HB08A-150W-50K-277V-9NS installation manual

Spitzer

Spitzer HB08A-150W-50K-277V-9NS installation manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.