Displays2go INTWHITWRD User manual

User Manual Rev. 19.08
INTERACTIVE WHITEBOARD
MODEL: INTWHITWRD
Scan QR code to visit the product page:
Operating Instructions for Whiteboard
Note: Before using the product, please read the instructions thoroughly!
If you have any questions regarding our products, please visit us at www.displays2go.com or
contact D2G customer service at 844-221-3393.

DISPLAYS2GO Table of Contents
Rev. 19.08 ii
Table of Contents
1. Introduction.............................................................................................................. 3
2. Set up the Whiteboard............................................................................................. 4
2.1 Wall Mounting...................................................................................................4
2.2 Floor Standing...................................................................................................6
3. Connection............................................................................................................... 7
4. Calibration................................................................................................................ 8
4.1 Install the Calibration Software. ........................................................................8
4.2 16- or 9-point calibration...................................................................................8
5. Technical Specifications....................................................................................... 11

DISPLAYS2GO Interactive Whiteboard
3
1. Introduction
Thank you for purchasing the interactive whiteboard with eMark Pen!
This interactive whiteboard system uses optical touch sensor, easily turns your projected screen
into an interactive touchscreen. It provides the ideal interactive platform for education and
business. presentations and lectures.
After connected with the included eMark Pen, you can draw or annotate on the interactive
whiteboard with this powerful stylus. Please refer to the user manual of the eMark Pen for more
information. Other opaque objects or your fingers can also work like a computer mouse.
Features:
Writing: users can write and draw on the whiteboard with included eMark Pen or a stylus
during a lecture or a presentation.
Annotation: users can easily operate and annotate on the screen during presentation
and lecture.
The eMark Pen can fully function with all the supported file types and applications,
including Word, Excel, PDF, PowerPoint, Internet browser, Whiteboard, OneNote, and
more.
No pressure required to activate the touch.
Powered by USB. No driver required. Plug and play.
Easy to set up and connect.
NOTE: To use all the functions of the interactive whiteboard, please connect it with the PC
installed Windows 10 operating system.

DISPLAYS2GO Interactive Whiteboard
4
2. Set up the Whiteboard
2.1 Wall Mounting
The wall mounting installation is quick and easy using the included hardware kit.
Minimum 2 people. Tools required: power drill, bubble level, adjustable wrench.
Hardware
a. Mounting Bracket –Top
b. Metal Bracket –Bottom
c. M8 Expansion Wall Anchor
d. M4 Screw
QTY.
2 pcs
1 pc
5 pcs
2 pcs
Step 1: Assemble the Metal Bracket (b) to the bottom back-side of the white board with (2) M4
screws (d), as shown below. Do not tighten the screws.
Step 2: Drill holes on the wall where the whiteboard will be. Drill 5 holes that are 38
⁄inch in
diameter and 2 inches deep at the locations marked as “A” below.
Metal Bracket (b)

DISPLAYS2GO Interactive Whiteboard
5
Step 3: Insert the (5) expansion wall anchors (c) into the holes drilled in step 2, then unscrew
the M8 Hex screw from the anchor sleeves. Make sure all anchors are flush against the wall.
See below:
Step 4: Insert a screwdriver or other metal rod into the anchor sleeve. Hit the other end of the
tool with a hammer to fix the anchors in the wall.
Step 5: Align (2) mounting brackets (a) to the upper wall anchors. Secure them to the wall by
tightening the hex screws back to wall anchors through the slots on the brackets.
Step 6: Carefully lift the whiteboard and hang it on the wall.

DISPLAYS2GO Interactive Whiteboard
6
Step 7: Horizontally slide the assembled bottom bracket at the back of the whiteboard, until the
wall anchor can be seen through the cutout on the bracket. Fix the bracket from the back by
tightening the 2xM4 screws on the back of the whiteboard.
Step 8: Use the removed M8 hex screw to secure the bracket at bottom to the wall. The
installation is completed.
CAUTION: For your safety, the whiteboard has to be mounted to solid wall ONLY.
Please use the included wall anchor and follow the installation instructions.
2.2 Floor Standing.
The whiteboard can also be used with a mobile/stationary stand.
Please find the floor stand that is compatible with the size of the whiteboard and will best suit
your needs.

DISPLAYS2GO Interactive Whiteboard
7
3. Connection
It’s easy to set up the interactive whiteboard. Just follow a few simple steps below, the
whiteboard will be connected and ready to use.
Connect the whiteboard with your PC and projector:
1) Insert the USB end of the provided serial cable into one USB port on your PC and insert
the other end of the cable into the whiteboard.
2) Connect the PC with the projector with HDMI or VGA cable (not included).
3) Power on the PC and projector. Adjust the position and focus for projected image as
needed. The connection is finished.

DISPLAYS2GO Interactive Whiteboard
8
4. Calibration
Calibrate after connected with the projector.
4.1 Install the Calibration Software.
Install the calibration software from the supplied USB flash drive onto your PC. Then
Find and open the “Optical Touch Device Control Panel” on your Windows desktop.
4.2 16- or 9-point calibration.
Click Setting at bottom of the calibration software.

DISPLAYS2GO Interactive Whiteboard
9
Choose “16 points” in “calibration” section then click “Apply” and “OK” to confirm the selection.
Next, click “Calibrate” to enter the calibration window.

DISPLAYS2GO Interactive Whiteboard
10
Follow the instructions on the screen: press and hold the blue dot. It will turn green after long
press.
After 16 dots all turn to green, the calibration is done. Press “OK”

DISPLAYS2GO Interactive Whiteboard
11
5. Technical Specifications
ITEM
SPECIFICATION
Whiteboard
Sensing Technology
Infrared/ Optical imaging touch technology
Sampling Rate
120 fps
Touch Points
Up to 10 Points
Touch Accuracy
±3mm
Touch Resolution
32768*32768
Response Time
≈8ms
Display Size
86’’
Aspect Ratio
16:10
Wall mounting
Supported
Touch Durability
Unlimited
Touch Object Diameter
≥10mm
Active Touch Area
72.91x45.59 in (1852x1158 mm)
Dimension
75.94x48.62x1.34 in (1929x1235x34 mm)
Interface
USB2.0 (Full Speed)
Power Requirements
DC5V±5%@500mA
Power Consumption
Average power consumption<2.5W, @5V
Software
Firmware Upgrade
Supported
Device Type
Touch (with gesture support per OS) or, Mouse (click,
drag, double click, right-click)
Calibration
4-point, 16-point, 25-point
Operating Systems
Windows 10
Environment
Operating Temperature
32°F～131°F
Storage Temperature
-13°F～167°F
Operating Humidity
10% to 90% RH, non-condensing
Storage Humidity
10% to 90% RH, non-condensing
Drift
No drift in operating temperature range

DISPLAYS2GO Interactive Whiteboard
12
ESD
Per EN 61000-4-2: Level 4, contact discharge 6KV, air
discharge 8KV